Showing results: 391 - 405 of 687 items found.
-
Model 4864 OEM -
ICS Electronics
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Fully IEEE-488.2 and SCPI compliant.* Includes 50-pin mating Relay connector and serial header connector.* Optional terminal board for easy connections without soldering. See the GPIB Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel. • 114521-12 Board provides 16 heavy duty form A contacts (SPST).* All other specifications are the same as for the 114521-11 Board. * 114521-14 provides 16 Relay driver outputs that sink 300 mA.* All other specifications are the same as for the 114521-11 Board.
-
FC3000 Series -
ACECO Electronics Corp.
The latest advance in RF finder Frequency range: 10 MHz - 3 GHz Weight: 210g Case: 80 mm * 68 mm * 31 mm stamped aluminum with black anodized finish Battery: Internal 4 * AA 600 mAH NiCd pack 7 digit liquid Crystal Display with 1 KHz resolution Low power consumption (Average 6 hour battery life) Hold switch to lock display Digital filter prevents display of random noise Low battery indicator Ultra sensitive synchronous detector 16 section bargraph to show RF signal strength Automatically holds and tunes ICOM CI-V or AOR receivers Measure frequency and period
-
SM-8X8-C6HDR-POE-HDBT -
Network Technologies Inc
The VEEMUX® HDMI Matrix Switch Over HDBase-T with Power Over Ethernet routes and distributes uncompressed HD 1080p, multi-channel audio, Ethernet, and IR from eight HDMI video sources to eight displays via inexpensive CAT6a/7 cable using HDBase-T technology. Power over Ethernet provides power to receivers that can be located up to 328 feet away.
-
SKS-H04GA -
Shanghai Sanki Electronic Industries Co., Ltd.
The high-frequency noise simulation generator is an EMC test instrument that reproduces high-frequency noise with a fast rise time when the switch is turned on/off. Since the pulse rise time is less than 1ns and contains wide bandwidth noise, it is very suitable for reproducing malfunctions. The line noise entering the power line and the induced noise entering the communication line can be reproduced, and the performance evaluation of the malfunction and function degradation of electronic products can be performed.
-
Series BOP-HV -
Kepco, Inc.
The Kepco Model BOP 500DM and BOP 1000DM are high voltage power sources, up to 500V or 1000V, respectively. These combine the capabilities of fast programmable power supplies with a Class A output stage, which can respond bidirectionally from zero. The BOP-HV can be operated in either a "voltage stabilizing" or "current stabilizing" operating mode (selectable by a front panel switch). These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant.
-
YAVTB000 -
6TL Engineering
When wiring a test fixture, you often have a need to join three or more wires onto the same test point. This module solves this problem, adding test points for manual test probes and a 4 position DIP switch. Circuits 1 and 2 feature up to 5 poles in parallel to increase the space for power supply terminals.
-
SparkFun Electronics
The LilyPad Simple Power is a simple e-textile board with a 500mA charge rate that lets you connect and charge a lipo battery and switch it on or off, that's it! We provide you with a JST connector and a slide switch, you supply the battery and sewing skills! With this LilyPad Simple Power, you should find no trouble in added a bit of power to your next wearable circuit.
-
Series MSK -
Kepco, Inc.
Kepco's MSK linear power supplies provide a selection of five models, offering 100 Watts of stable benchtop power. They use a high gain linear (series pass) stabilizer circuit for ultra low noise and low ripple output, good stability, and accurate resettability, and they are MIL-STD-461 compliant.MSK's "Preview" switch (d-c on-off) allows voltage and current to be pre-set with the digital meters displaying the set values. At "d-c off," no voltage is applied to the output terminals and no load current needs to be drawn to set the current limit. At "d-c on," the set voltage is applied to the output terminals, the appropriate mode indicator illuminates and the meters indicate actual voltage and current.
-
60-200-001 -
Pickering Interfaces Ltd.
If you have ever read the term “programmable except for the supply on/off switch” the 60-200 can provide this capability in a system with the added benefit of an easy to use LXI interface. The 60-200 is a power management switch that provides a means of remotely controlling the power status of up to 8 instruments.
-
MFJ-267 -
MFJ Enterprises, Inc.
1.5 kW Dry Dummy Load has built-in precision, true peak-reading SWR/Wattmeter switchable to external antenna! Worlds most versatile 1.5 kW dummy load has a built-in true peak reading SWR/Wattmeter that you can switch and use independently! Youll find tons of uses! Tune up your transceiver, linear amplifier, or antenna tuner into a safe 50 Ohm dummy load at full power.
-
Alliance Support Partners, Inc.
An increasing number of electronics products are being assembled in panels of 8 or more to minimize production cost. These products are typically tested with in-circuit tests (ICT) followed by power-on functional tests. Normally, ICT requires isolation of power and ground while measurements are being performed. Functional tests, including in-system programming (ISP), require board power to be applied. The Modular Relay Board (MRB) is designed to switch power onto each individual board and to disconnect sensitive signals during functional test.
-
A-LAR Series -
Zaber Technologies Inc.
Zaber's A-LAR Series products are computer controlled, lead screw driven, motorized linear actuators (electric cylinders). They are stand-alone units requiring only a standard 48 V power supply. A manual knob at the end of the unit permits manual control - press and hold to switch between velocity mode and distance mode, turn to move the actuator, and press to stop.
-
UTC041 -
Vadatech Inc
The VadaTech UTC041 is the most feature-rich conduction cooled MicroTCA Carrier Hub (MCH) on the market. Its management software is based on VadaTech’s robust Carrier Manager and Shelf Manager which have been deployed for years with proven results. The MCMC manages the Power Modules, Cooling Units, and up to 12 AMCs within the chassis. It also manages PCIe Gen3 or 10GbE XAUI fabric switch as well as the standard GbE with 10GbE uplink Base Channel switch.
-
TW3207 -
Techwin(China) Industry Co., Ltd
Multi-Meter TW3207 integrates the functions of an intelligent optical power meter module and of a highly stable light source module in one unit which can perform closed-loop tests by incorporating both modules. Individual regimes of operation can also be manually chosen using menu operation to switch functions. A perfect combination to make your optical fiber tests a lot more convenient.
-
Polatis, Inc.
Polatis Optical Switch Modules (OSM) are high-performance, fully non-blocking all optical matrix switch modules with port counts from 4x4 up to 144x144. Versions are also available for "any-to-any" port connectivity, which enables new interconnection architectures not possible with traditional symmetric NxN switch matrixes. The modules are designed for easy integration by OEMs integrating all optical switching with network equipment and are designed to meet the highest performance and reliability needs of the most demanding applications with exceptionally low optical loss, compact size, low power requirements and fast switching speeds.