Filter Results By:
Products
Applications
Manufacturers
-
product
Electrical Contacts Test
The electrical contact testing is performed to determine the reliability of equipment under various contacting conditions. A few types of electrical contact tests are: contact-chatter monitoring, contact resistance, intermediate, and low level contact switching.
-
product
LED CIRCUIT TESTER, 6-12V AND 24V
MD1646
*Checks high and low voltages on 6-12V and 24V circuits*Connect the red lead to a power source and the black lead to a ground source*Tester will light up red for power and green for ground during testing
-
product
Temperature Cycling Test Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL Temperature cycling test chamber is suitable for testing various performance indexes of aerospace products, electronic instruments, materials, electronic products and various electronic components under the condition of rapid temperature change.
-
product
Voice Quality Test
POLQA
POLQA is the next-generation voice quality testing technology for fixed, mobile and IP based networks. POLQA was standardized by ITU-T as P.863 and can be applied for voice quality analysis of HD Voice, 3G and 3G/LTE networks.
-
product
Drying Oven
Sanwood Environmental Chambers Co ., Ltd.
Drying Oven can provide a stable test space for pre-heating, drying, changes about physics and chemistry testing . It supplies precision temperature controller with high stability of platinum resistance to temperature that makes temperature well-distribution.
-
product
Instrumentation
Unholtz-Dickie designs and manufactures a variety of transducer signal conditioners, accelerometers, remote charge preamplifiers, vibration monitors & limiters, transducer testers, buffer amplifiers and other special purpose instrumentation accessories for vibration testing.
-
product
Advanced NDT Data Acquisition & Analysis
WeldSight™ software’s comprehensive acquisition and analysis tools enable you to engineer compliant and repeatable advanced phased array (PA), ultrasonic testing (UT), and time-of-flight diffraction (TOFD) weld inspections.
-
product
Electrical Safety Tester
PSE AG has developed an electrical safety test that combines different tests for the testing of PV modules. With our four-in-one tester it is possible to test the following according to IEC 61215-2 and IEC 61730:
-
product
Mini PCI Card
EXC-1553mPCIe/P1
This card’s small size and suitability for Mini Card compatible computers make it a complete solution for developing, testing, integrating 1553 interfaces and for performing system simulation of the MIL-STD-1553 bus, both in the lab and in the field.
-
product
Stand-Alone Programmer and Hardware Debug Interface
Cyclone MAX
Cyclone MAX is an extremely flexible tool designed for in-circuit flash programming, debugging, and testing of Freescale ColdFire V2/V3/V4, Power Architecture 5xx/8xx, Power Architecture 55xx/56xx (Nexus), and ARM (MAC7xxx) microcontrollers.
-
product
Trailer Light Tester
LT35
The LT35 performs complete testing of a trailer’s light system. Its unique design allows it to be powered by your trailer’s battery* or any 12v power source, such as a portable power pack, jump box, or battery.
-
product
PCIe
M.2 Gen4 Socket3
SCHILLER AUTOMATION GmbH & Co. KG
The PCIe Gen4 M.2 Socket 3 test adapter or test fixture kit facilitates Device and Host compliance testing for PCIe Gen4 M.2 Socket 3 Source and Sink devices.
-
product
PCIe
M.2 Gen4 Socket2
SCHILLER AUTOMATION GmbH & Co. KG
The PCIe Gen4 M.2 Socket 2 test adapter or test fixture kit facilitates Device and Host compliance testing for PCIe Gen4 M.2 Socket 2 Source and Sink devices.
-
product
Discharge Test System
The automated testing equipment automatically performs charge and discharge of energy devices such as the rechargeable batteries(cells, modules, packs) that are installed in PHV/ EV and mobile devices, while measuring the voltage, current, temperature, and impedance.
-
product
High Volume Manufacturing Handling, Stimulus
ULTRA P
The ULTRA P is a high performance production handler that provides thermal conditioning, full 6 DOF mechanical stimulus and an electrical ATE signal path for testing Micro-Electro-Mechanical Systems (MEMS) Accelerometers and Gyroscopes.
-
product
MEMS Handler
4664-IH
The ULTRA P is a high performance production handler that provides thermal conditioning, full 6 DOF mechanical stimulus and an electrical ATE signal path for testing Micro-Electro-Mechanical Systems (MEMS) Accelerometers and Gyroscopes.
-
product
Digital Functional Test
CTS100i
Capable of performance testing to defined traceable standards, CTS100i is designed to test Military, Aerospace and Safety-Critical equipment. CTS100i is a cost-effective digital functional test system, available in single, dual and three bay versions.
-
product
Forced Air Cryogenic Cooling
FixTreme TE
FixTremeTE is a cost-effective standalone alternative to mechanical or forced air cryogenic cooling. When paired with a Testforce dbGuard Series RF shielding test enclosure, performing at temperature RF & microwave functional testing is simple.
-
product
Bell Prover Gas Meter Test Bench G1.6-4
Bofa Instrument & Equipment Co., Ltd
Bell prover gas meter test bench is an equipment to test domestic gas meter G1.6-4, the flow range 0.016m3/h~6m3/h. It is an ideal testing equipment for gas meter factory and R&D institute.
-
product
Micro Dyne System
With over 50 years' experience in dynamometer design and torque measurement, Magtrol has revolutionized the industry. Magtrol's NEW Micro Dyne, capable of measuring extremely low torques (2.0 mNm can be resolved to 0.0004 mNm), is DESIGNED EXCLUSIVELY for testing miniature and micro motors.For the utmost convenience, the Micro Dyne is packaged as a COMPLETE MOTOR TESTING SYSTEM. Everything that is needed to accurately and efficiently test miniature motors and micro motors is included with the purchase of a Magtrol Micro Dyne. The only component that needs to be supplied by the customer is a laptop or desktop personal computer and a motor power supply.
-
product
100GBASE LR4/ER4 Wavelength Selective Power Meter
KI6512
KI6512 is an easy and economical handheld 100GBASE LR4/ER4 Wavelength Selective Power Meter for testing multi-λ single mode fiber optic systems. It scans and stores the absolute or relative power levels of all 4 channels in 0.8 seconds. Test data can be viewed in graphical or numerical form, and reference values can be stored for easy loss testing. An extra 50/125u power meter port gives additional flexibility at 850 / 1300 / 1550 nm. This port only supports basic functions, but is very handy for first-in fault finding and investigation.
-
product
ARINC HSI / ADI Test Fixture
TA-2000
The TA-2000 test fixture is a combination panel that incorporates all the standard capabilities of the legacy CTS-11(ADI) and CTS-12(HSI) panels and much more. This panel is married to our model TA-1001 dual synchro transmitter/API panel thus allowing for local stimulus and alignment of the instruments synchros and resolvers. The panel provides for testing of both superflag(28v) and low level meters through a matrix of switching that will allow testing of all meters simultaneously or just individually. The low level meter drive circuit also incorporates an automatic mode that will continuously oscillate the L/R and Up/Dn pointers.
-
product
400, 200, 100 Gbit Error Rate Tester
PAM-4 BERT
The MI-PE5610-1 is a PAM-4 BERT with an integrated propriety, optical PAM-4 modulator. ROSA testing is tremebous simpliefied by the integration of the optical PAM-4 modulator in the BERT chassis. This ROSA testing solution saves time and avoids trouble shooting and accelerates your product development. The BERT provides an excellent optical PAM-4 reference output signal with adjustable OMA of the three PAM-4 eyes.The implemented 3-Eye BER technique measures the BER in real time of the 3 eyes simultanously.A wide range of selectable pattern for compliance test and signal analysis is supported.
-
product
Advanced Circuit Card Automated Test
ACCAT
The ACCAT is designed to support diagnostic and acceptance test requirements across a wide spectrum of testing parameters. ACCAT provides a suite of core parametric test instruments, advanced GUI based software, Huntron Access Robotic probing and Huntron Analog Signature Analysis (ASA). ACCAT provides stimulus and asurement capabilities necessary for full functional and parametric testing of circuit card assemblies along with robotic guided probes for fault verification and debug. The Huntron ASA test is ideal for pretest or safe to power up procedures protecting the integrity of the test system.
-
product
SpikeSafe DC / Continuous Pulsed Current Sources
The Vektrex SpikeSafe™ DC / Continuous Pulse (DCP) Current Sources provide reliable DC or pulsed drive for LED or laser diode reliability testing, IESNA LM-80 maintenance testing, and other test applications requiring DC or continuous pulse current. Models support currents from 500mA to 60A and compliance voltages from 50V to 400V. All models feature individual channel control, accurate pulsing over long output cables, precise current, precision pulsing for improved measurement repeatability, and high power density — typically 6.4kW-8kW.
-
product
AUTOMATED SAFETY AND COMPLIANCE
DMC's test and measurement system offerings include designs and development of Automated Safety, Compliance, and Benchmark Testing. These serve interests of commercial product certification, including fire hazards, safety and signaling, lighting, building safety, energy, and hazardous location testing. These also serve interests of product and technology benchmarking, including brand quality protection, consumer quality, and energy efficiency. Test systems have been developed by DMC to support many standards, including UL (Underwriters Laboratories), Consumer Reports, Intertek, Energy Star, and EN / CEN European Standards.
-
product
CPCI BUS Interface Card
Cpci301 MIL-STD-1553
MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator / Analyzer / Tester CPCI BUS Interface Card - The CPCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.
-
product
ESD LCD SURFACE RESISTIVITY METER (WITH 1 PAIR OF 5 POUND ELECTRODES)
The ESD LCD SURFACE RESISTIVITY METER provides everything necessary to test work surfaces using the procedure outlined in the EOS/ESD-S4.1 standard. This test kit makes testing surface resistance easy – simply place the weights attach the cables, switch to the correct voltage and press the button to read resistance directly on the meter. The meter incorporates parallel probes on the bottom of the unit which allows the user to make surface resistivity measurements. The parallel probes allow for quick and easy testing of a variety of surfaces and materials, without the use of the five pound electrodes
-
product
Cable Certifiers
LANTEK III Series
New permanent link adapter saves money. Send test data anywhere using IDEAL AnyWARE app. Certifies multimode and single-mode fibre (optional). Professional PDF reports with free software. Certifies twisted pair cabling to TIA/ISO standards. The LanTEK III is an easy to use cable certifier that meets existing TIA and ISO/IEC performance requirements for testing up to Cat 7A/1000MHz. FiberTEK III adapters are used with LanTEK III for fast and simple certification of high bandwidth single-mode and multimode fiber optic cabling including support for encircled flux testing.
-
product
High Precision Spectroradiometer Integrating Sphere System
LPCE-2(LMS-9000)
LPCE-2 is an Integrating Sphere Spectroradiometer LED Testing System for identifying the performance of single LEDs and LED lamps. LED’s quality should be tested by checking its photometric, colorimetric and electrical parameters. According to CIE127-1997, IES LM-79-08 and IES LM-80-08, it recommends to using an array spectroradiometer with integrating sphere to test SSL products. The LPCE-2 system is applied with a CCD Spectroradiometer (LMS-9000B or LMS-9000A) and worked with A molding integrating sphere with testing holder base function which will be more circle and the test results will be more accurate than the traditional integrating sphere.