Showing results: 5521 - 5535 of 8452 items found.
-
AmFax Ltd
PXI has become the de-facto standard for housing the high performance modular instrumentation required to meet the demands of testing today's high performance products. Based on the PCI bus, PXI (PCI Extensions for Instrumentation), this platform is used in most of our new ATE designs.
-
6500 series -
Chroma ATE Inc.
The global AC power testing requirements demand more sophisticated AC Power Source that is capable of simulating a wide variety of AC line conditions, harmonic waveforms, accurate power measurement and analysis. The Chroma 6500 series Programmable AC Power Source delivers the right solution to simulate all kinds of normal/abnormal input conditions and measure the critical characteristics of the product under test. It can be used for R&D design characterization, production testing, and QA verification of commercial, industrial, and aerospace electronic products. The Chroma 6500 series delivers maximum rated power for any output voltage up to 300 Vac, and at any frequency between 15Hz to 2000Hz. It is suitable for commercial applications (47-63Hz); for avionics,marine, military applications at 400Hz or higher frequency; or for electrical motor, air-conditioner test applications at 20Hz. All models generate very clean sine or square waveforms output with typical distortion less than 0.5%. The Chroma 6500 series has built-in Direct Digital Synthesis (DDS) Waveform Generator to provide user programmable high precision waveform. For testing products under AC line distortion conditions, clipped sinewave can be generated with 0% to 43% distortion and amplitude from 0% to 100%. It also can simulate all kinds of power line disturbances such as cycle dropout, transient spike, brown out, phase angle, voltage and frequency ramp up (ramp down), etc.. Up to 30 harmonic waveforms are factory installed, and testing for compliance to AC line harmonic immunity standards can be easily achieved in the field.
-
MD-250-HD -
Mustang Dynamometer
The MD-250-HD series dyno (SE/DE) was designed to be a performance dynamometer first with the added benefit of being able to test 2-wheel-drive heavy-duty vehicles such as truck, buses and commercial vehicles in addition to the standard car or light duty pick-up. The 250-HD is certified in the states of Colorado, Nevada and Utah for use in loaded-mode diesel smog testing programs because of its accuracy and reliability. No other dyno in its class offers more value or better in-house motor vehicle testing capabilities than the Mustang MD-250-HD. For starters, the MD-250-HD boasts a 1,500 horsepower measurement capacity at a top speed of 175 mph and a powerful air-cooled eddy current brake provides the MD-250-HD-SE with 900-hp worth ofloading capacity for steady state testing. Loading capacity can be increased to 1,500-hp via the optional DE model. The 250-HD can be upgraded to the 250-HD-SE-M via the addition of a 100 or 200 hp AC motor for transient testing of electric buses to measure range and regeneration or for emissions testing of IC engines. Do not be fooled by its compact size – the MD-250-HD is a serious dynamometer with serious tuning capabilities. The MD-250-HD uses a powerful eddy current power absorber, a frictionless, air-cooled braking device, to enable it to apply variable and steady state loading. A complete control and data acquisition system lets you design a wide range of tests or select from a host of pre-configured tests included with the standard system. The 250-HD’s four roller design makes setting up vehicles a snap – simply drive onto the 250-HD and let the tires settle in between the rollers. The 250-HD can be installed above-ground or below-ground, it’s your choice. The above-ground system utilizes an optional premium platform and ramp system with an above-ground restraint kit. The addition of an axle pull-down kit help keep the tires from slipping or trying to “climb out” of the rollers.
-
EMC-3C -
MVG EMC
This compact 3 meter test range will settle into test areas of limited space while continuing to produce exceptional performance for EMC measurement. Emission quiet zones of up to 1.5m are accommodated with very repeatable results. Suitable for EMC pre-compliance emissions and compliant immunity testing.
-
Labfon Equipment Inc.
Flame Photometers are used widely in the measurement of alkali elements concentration in all sample types in: Mineral Extraction, Oil Industry, Paper Industry, Pharmaceuticals, Soil Analysis, Utilities, Food & Beverage, Chemical Manufacture and Fertilizer and Clinical laboratory testing and Pathological study in medical health.
-
MCE -
PdMA Corporation
The MCE? (Motor Circuit Evaluator) is a comprehensive static motor tester that produces detailed analyses of motor and circuit conditions in as little as three minutes. Analysis of the motor and associated circuits through MCE? testing allows for the detection of electrical faults in any one of the five fault zones.
-
Acoustics for Communications
Audio, acoustics and electroacoustics testing and assistance for your product. * Audio Laboratory equipped with precision instruments from Bruel and Kjaer and others. * Emphasis is on product and component analysis not general acoustics. * TIA, ANSI, IEEE, ITU-T, ETSI, AES, UL, EN, IEC standards expertise.
-
E7000L -
Deviser Instruments
The E7000L Cable & Antenna Analyzer provides all necessary measurement functions and performance to accurately diagnose and verify the site's cable and antenna system and RF connectors, as well as basic fiber-feedline testing. Smaller and lighter than the E7000B, the E7000L is ideal for installation of wireless cell sites.
-
Kongter Test & Measurement Co., Limited
Kongter offers a whole line of products for testing and measurement of battery from your critical power systems. It includes battery online monitoring system, battery tester for internal resistance/conductance, battery charger, battery load bank, battery data logger, battery charger/discharger and so on.
-
ELMA -
Applied Precision Ltd.
The Electricity Meter Test Equipment ELMA due to modular concept enables to tailor specifications to specific laboratory demand. The available power and the maximum current of 240 A of extremely pure synthesized 4-quadrant test signal covers the needs of both precision and high capacity testing laboratories.
-
LDF Series -
Bemco Inc.
The Bemco LDF Series of wide range expendable refrigerant chambers are designed for low initial cost, rapid temperature cycling, environmental stress screening (ESS), and for handling large thermal loads. These systems are compact for their size, can be bench mounted, and are easily modified to special testing configurations.
-
Com-Power Corporation
Com-Power's Current Injection Probes are used for RF conducted immunity testing per IEC 61000-4-6, CISPR 16-1-2, RTCA DO-160 and MIL-STD 461. Current injection Probes are to be used only when there is no commercially available CDN for the type of port(s) to be tested.
-
Shanghai Fibretool Technology Co.,Ltd.
Designed to aid in the testing of fiber optic cable when using an OTDR. TheOTDR Launch Cable Box is used with Optical Time Domain Reflectometers (OTDRs) to help minimize the effects of the OTDRs launch pulse on measurement uncertainty. Available in many different configurations and fiber lengths.
-
DG Technologies
The best value in CAN pass-thru device hardware. Use it for validation, network development, and test fixture to module network communication. Also a great tool for End-of-Line testing and using your own software for ECU and network prototypes. It is compatible with all of today’s industry standards.
-
Shanghai Fibretool Technology Co.,Ltd.
Designed to aid in the testing of fiber optic cable when using an OTDR. TheOTDR Launch Cable Box is used with Optical Time Domain Reflectometers (OTDRs) to help minimize the effects of the OTDRs launch pulse on measurement uncertainty. Available in many different configurations and fiber lengths.
