Filter Results By:
Products
Applications
Manufacturers
-
product
Online OK Tester for Electronic Ballast and CFL
WT-1
• Test 6 pieces at one time, suitable for mass testing in assembly line. • Measure parameter: Vrms, lrms, W, PF. • Freely set upper and lower limit for lrms, W, PF, alarm when value out of limits. • Freely set test duration in range: 0-99.9s, tested data automatically locked. • Test range: 1) Vrms: 10.0-300.0V 2) lrms: 5-999mA 3) W: 0.1-300.0W 4) PF: 0.0001-1.000 • Accuracy: 0.5% • Digital display on 6 windows is easy to read • Print port and communication port available (optional)
-
product
Precision Integrated Analog Front End, Controller, & PWM for Battery Test & Formation Systems
The AD8452 combines a precision analog front-end controller and switch mode power supply (SMPS), pulse-width modulator (PWM) driver into a single silicon platform for high volume battery testing and formation manufacturing. A precision instrumentation amplifier (in-amp) measures the battery charge/discharge current to better than ±0.1% accuracy, while an equally accurate difference amplifier measures the battery voltage. Internal laser trimmed resistor networks establish the in-amp and difference amplifier gains (66 V/V and 0.4 V/V, respectively), and stabilize the AD8452 performance across the rated operating temperature range.
-
product
Power-Switching Test System
High Voltage Switching Test System
The Accel-RF Power-Switching Test System is capable of measuring reliability under a variety of conditions for switching power applications up to 1kV (off) and 25A (on) at rates up to 1MHz switching frequency, dependent on voltage. By leveraging technology developed for the RF burn-in tray platform with new fast switching measurement techniques, this system can support testing of multiple devices under elevated temperature stimulus in a small physical area, and offers the flexibility to test both soft- and hard-switching applications. The Accel-RF Power-Switching System is the most flexible and accurate power switching platform available.
-
product
RF Bias Burn-In System
These systems deliver an unbeatable combination of advantages over a wide range of RF frequencies and power levels. The Automated Multi-Channel RF-Biased Burn-In Test System is a turnkey system that incorporates all of the capability needed for accelerated aging and parametric testing of RF semiconductor devices. Its powerful software elegantly supports data acquisition, storage, and presentation. Accel RF’s customers choose system features to meet their technical needs and capital budget. In addition to cost savings, use of Accel-RF’s solutions accelerate product time-to-market, saving many months of product development.
-
product
ESD & Latch-Up Test System
Identify and help correct ESD and latch-up susceptibility issues on sensitive integrated circuit components prior to full-scale production with the Thermo Scientific™ MK.2-SE ESD and Latch-Up Test System. The MK.2-SE test system provides advanced capabilities to test high pin count IC devices to Human Body Model (HBM) and Machine Model (MM) ESD standards. The system’s pulse delivery design addresses wave form hazards such as trailing pulse and pre-discharge voltage rise, and performs Latch-Up testing per the JEDEC EIA/JESD 78 Method.
-
product
Failure Analysis
A partial list of our state of the art test equipment, applicable to these testing disciplines, will include the following: Two Scanning Electron Microscopes with EDS (SEM/EDS) Three Differential Scanning Calorimeters (DSC) Three Thermogravimetric Analyzers (TGA) Three Thermo Mechanical Analyzers (TMA) One Dynamic Mechanical Analyzer (DMA) Two Real-Time Fluoroscopic X-ray Systems, including a Microfocus System One Fourier Transform Infrared Microscope (FTIR) (capable of identifying a single particle of an unknown material) Two Ion Chromatographs (IC) (capable of identifying ionic impurities in ppm)
-
product
Time Coating Meter
- Magnetic induction (F) method is used to measure the thickness of non-magnetic coating on ferrous metal- Eddy current (N) method is used to measure the thickness of non-conducting coating on non-ferrous materials- Automatic recognition of substrate- Automatic selection of measuring methods- 5 statistical ways: Mean values / Max. values / Min. values / testing numbers.(No.) / standard deviations (S.DeV)- Upper-lower limit setting and sound alarm- Data output to printer or PC by RS232 cable- 500 readings can be stored- 2 measuring modes: continuous / single- 2 stop ways: Manual/automatic
-
product
Fully Automated In-line Test System For LED Light Engines
We are pleased to announce that we have received an order for the supply of a fully automated in-line test system for testing LED light engines from ASD Lighting, based in Rotherham. The solution provided, consists of an in-line handler fitted with a vision system. The camera software is capable of learning the position of all LED’s on a new pcb, thereby reducing the time to introduce a new product. In addition to identifying the location of any missing or faulty LED’s the tester measures the colour temperature of every pcb. An image is taken of faulty units with the location of any missing LED’s identified
-
product
Digital Controller
SPARC Controller
SPARC Brake is a digital controller optimized for Inertia Brake Dynamometers. As a member of the SPARC family of universal controllers, SPARC Brake is using a modular design to enable more flexible configurations to fulfill any specific test environment.SPARC Brake uses sophisticated control algorithms and provides superior and intelligent control of brake actuators with highest control accuracy to cover the wide range of brake test applications. From simple static brake testing to high dynamic simulation procedures, it is able to meet the highest demands for today’s and tomorrow’s brake test requirements, for example GM-TIP.
-
product
Laser Diameter Measuring Instrument
RC-078
The RC-078 Laser Diameter Instrument is a high accuracy one without contacting designed on the basis of the laser scan measuring principle. The 2-dimension measuring mode is applied to the instrument, and the 2-way laser beam is in the positive cross design in the measuring field, thus effectively eliminating testing errors caused by work piece shocks. It is special suitable for real-time measurement of the production field, and widely used in the test of round wire materials such as communication cables, optical cables, co-axial cables and power cables, and the test of various kinds of other round work piece diameters.
-
product
On-site Oil Analyzer
MicroLab 30
MicroLab 30 is designed for fleets operating over-the-road vehicles or generator equipment. This analyzer best suited for companies interested in testing primarily engine oils to determine the serviceable life of the oil and the equipment condition. The MicroLab 30 analyzes six oil chemistry parameters along with viscosity to determine proper drain intervals. The standard 10 element version provides information on oil contamination and wear metal analysis to determine if mechanical issues exist. The MicroLab 30 can be upgraded to 20 elements if there is an interest to analyze oil additive levels as well as additional wear metals.
-
product
Wide Range High Voltage Programmable DC Power Supply
N3600 Series
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N3600 series is developed based on NGI's years of experience in testing for battery fluctuation simulation test, battery charger, high voltage diode, electrolytic capacitor, electromechanical control, ATE test system, etc. It is a high-voltage wide-range programmable DC power supply. According to different test environments in the fields of lab test, system integration test, and mass production line, NGI has made a number of optimization designs based on the international advanced technology. N3600 series is a market leader in similar products in terms of reliability, maintainability and safety.
-
product
Xenotest
220/220+
Atlas Material Testing Technology
The Xenotest 220 and Xenotest 220+ are large capacity lightfastness testers dedicated for textile testing. They come with premium on-rack light and temperature sensor and non-aging optical filter technology. With the ability to test 38 samples, the 220 Series provides nearly twice as much capacity in the same footprint compared to 150S+. The combination of its large test chamber and the efficient use of power and water make it today‘s most economic air-cooled instrument available. It complies to standards ISO 105 B02, AATCC TM16 (option 3), and Marks & Spencer C9, C9A.
-
product
Walk / Drivable test facilities
TW / CW series
Walk or drive-in temperature and climatic test chambers can be designed from CTS by a standardized grid system affordable in all sizes. The refrigeration performance data are adjusted here by our experienced sales and project engineers on your testing out. The walk / drive-chambers are ideal for larger components and finished products. CTS as a medium sized company attaches great importance to the detail quality of the equipment components, with only the best supplier products such as compressor and solenoid valves are used. Your resulting advantages are trouble-free long-term operation and thus no loss of valuable test time.
-
product
GB-GRAM/GB-GRAM-M Interface Card
Valiant 153M
Valiant 153M is a GB-GRAM/GB-GRAM-M (GB-GRAM/M) interface card that allows the simultaneous operation and testing of a commercial- off-the-shelf (COTS) receiver and a GB-GRAM/M. Both receivers are powered and communicate using a single USB mini cable. By integrating a COTS receiver onto the Valiant 153M, users can perform cross-checks to determine if the military receiver is connected and communicating data properly. Both receivers communicate via the onboard USB mini or RS-232 serial connectors. The Valiant test fixture was designed to be nearly the same size as the GB-GRAM/M type I card.
-
product
ACCUplace Position Grid
AP-P Series
The AP-P is a unique calibration target that is designed to test the position and/or recognition ability of a vision system. The matrix of small scales, precisely positioned in a grid matrix format, makes testing for subject recognition and system positioning simple.The overall target is comprised of a matrix consisting of 6.0mm x 6.0mm square individual components each having a 5.0mm x 5.0mm X & Y Scale with 0.100 divisions. The scale has pitch accuracy of 1μm. The AP-P is available on two standard materials; Chrome on Glass (CG) and Chrome on Opal (OP).
-
product
Network Emulation System
Mini Maxwell
Mini Maxwell -- Easy to use, portable, network emulator. Mini Maxwell''''s low cost of $1995 can fit into any testing budget. The Mini Maxwell is great if you have low power requirements, or need ultra quiet operation. Mini Maxwell supports packet drop/loss, duplication, delay (latency)/jitter, reorder, and burst. Includes: processor, memory, and three Ethernet interfaces in one enclosure with separate power supply, Linux OS, Mini Maxwell network emulator engine, graphical user interface, and 90 Day Warranty.
-
product
Test Probe Kit
69600
Kit includes 14 flexible test probes, long straight probe, piercing back probe, crocodile clip, 4mm circuit tester adapter and Deutsch spooned probe. The probes are designed to be used on popular Weather-Pack, Metri-Pack and Micro-Pack style connectors. The test probes are 5" in length and are flexible to help eliminate damage to the connector terminals that can result from testing with a standard test probe. The 4mm adapter allows conversion of some circuit testers to a 4mm banana connector, which provides a better connection. Kit comes in a pouch for storage.
-
product
Case Depth Hardness Tester
HTD-4000
HTD 4000 is used to measure case depth and is capable of verifying case depths ranging from 0.4mm (16 thou) up to a maximum of 2.5 / 2.8mm (100110 thou). Our system utilizes a new and very advanced principle based on the continuous measurement of the electrical resistance in relation to the working load applied. Our design meets the demands of the heat treatment industry. HTD 4000 is equipped with a big stand to enable the testing of large work pieces having overall dimensions up to 550mm (22") in height and 350mm (13.8") depth
-
product
Shoes and Wrist Strap Tester
WST100
• Tester designed for checking the conformity of operators wrist strap and/or shoes to the ESD protection standard.• It is also designed to be permanent wall mounted in a production facility for daily testing of employee’s wrist straps and footwear.• Easy to operate, red and green LEDs give clear “pass” or “fail” indication• Individual tests for the wrist strap, the right and left shoe• Can register up to 60 000 different measurements• Output for interface with PC or automatic door opening system• Operates battery that can be supplemented with an AC net adaptor• Tester and calibration plug are delivered with a certificate ofcalibration
-
product
System Instruments
bsw TestSystems & Consulting AG
Many tasks in the area of semiconductor characterization as well as in the testing of electronic assemblies are routine tasks. Test series of new building elements or samples from production are routinely measured in a large number of electrical parameters. For this, you do not need a measuring device with a complex graphical user interface. A simple interface for remote control with a PC is sufficient. The evaluation and visualization of the results is also carried out on the PC. With the Keysight E5270B and its "little brother" the E5260A two powerful modular SMU units are available for the purpose of the integration into automatic test systems.
-
product
Wound Component EST Analyzer
19036
Chroma Systems Solutions, Inc.
The industry’s first Wound Component Electrical Safety Test (EST) Analyzer that combines impulse winding, AC/DC hipot, insulation resistance and DC resistance test measurement functions. Chroma’s 19036 Wound Component EST Analyzer has 5kVac/ 6kVdc high voltage output, 5kV insulation resistance, 6kV layer short impulse voltage and 4-wire DC resistance measurement with a maximum output of up to 40 channels. Capable of outputting and measuring AC100mA/DC 20mA, Chroma’s 19036 is suitable for testing to high power motor standards such as UL 1004-1.
-
product
Chroma LCR Meters
Chroma Systems Solutions, Inc.
Some of the key features to look for in an LCR meter (also known as an impedance meter) are: accuracy, test frequency, measured parameters, test voltage and test current. Additionally, an easy to understand display of test results and the ability to access and use these results has become increasingly important. Component testing often requires much more than simply a resistance, capacitance or inductance value at a given test frequency and stimulus voltage. An LCR meter or impedance meter must have the flexibility to provide multi-parameters over wide frequency and voltage ranges.
-
product
Data & Protocol Converter
uMACC
The uMACC is a wholly contained Communications Converter (data converter - protocol converter or translator). Its small size makes it a complete solution for developing & testing both in the lab and in the field.The uMACC can carry up to 4 modules. Each module can be one of the following protocols: 1 dual redundant MIL-STD-1553/1760 interface1 H009 channel5 MMSI channels5 ARINC-429 channels2 ARINC-708 channels2 ARINC-717 channels5 ARINC-825 (canbus) channels2 Serial channels (RS-232/422/485, NMEA 0183)Ethernet (10/100/Gigabit)10 Discrete I/O signalsAnalog to Digital / Digital to Analog
-
product
Functional Test Fixtures
Intrinsic Quality delivers turnkey standalone Functional Test fixtures and Windows based functional testers that are custom engineered with innovation and reliability to meet your testing needs. Our experience and expertise ensure a production ready functional test solution that is cost-effective, on time and on budget. Our broad range of test solutions includes simple continuity testers to complex microcontroller assembly testers. Our customers include military, aerospace, automotive, medical and consumer OEMs. We serve the needs of low volume high mix CEMs and off shore high volume manufacturers.
-
product
Multi Protocol Boards
The EXC-4000 carrier board series was developed to meet the needs of avionic testers for multi-protocol integrated, digital bus testing. Modules may be selected out of a growing list which currently includes MIL-STD-1553/1760, MMSI, H009, ARINC-429, ARINC-708/453, Serial (232/422/485), Discrete and CAN bus. Additionally, an IRIG B decoder implements a global time stamp relative to the IRIG B pulses. The need for higher density, different protocols, and multi-channel on one integrated test card has made the EXC-4000 series very successful.
-
product
Static Sensor
718
Portable Meter for Testing of Electrostatic FieldsMeasures surface voltage and polarity on objects up to ±19.99 kV at a distance of 1 inchSwitch Selectable Measurement RangesProvides readings from 0 to ±1.999 kV and 0 to ±19.99 kVChopper-Stabilized Probe TechnologyAllows for use in ionized environmentsDurable Dissipative Housing Design with Membrane SwitchesProtects meter from physical damage and minimizes wearLED Range FinderRed ranging lights help operator to place the meter at the correct distance from the object being measuredHold ButtonAllows the measurements to be retained for easy reading and extends battery life
-
product
TTESync For VxWorks 653
TTESync is a synchronization component that allows tight synchronization of VxWorks 653 partitions to the fault-tolerant system-wide cycle time of the TTEthernet communication network. All partitions executed on different modules can be “pinned down” within the overall system cycle time, thus enabling the lowest latency and minimum jitter in message exchange among distributed functions. At system level this results in clean layering, well-understood functional interactions and simpler application design, testing and system integration. System architects can reduce system complexity and further optimize system size, weight, power (SWaP) and life-cycle costs.
-
product
SoC Test System
V93000 SoC / Smart Scale
Advantest’s V93000 Smart Scale generation incorporates innovative per-pin testing capabilities. Each pin runs it own sequencer program for maximum flexibility and performance, for example in multisite applications. Full test processor control ensures time synchronization between all card types, like digital, Power, RF, mixed signal and so on. The user benefits are reduced test time, best repeatability and simplified program creation. The system design makes it easy to extend your configuration with new modules and instrumentation, as your test needs change.
-
product
Thermal Monitoring System
The monitoring system for the thermal state of traction electric locomotive machines is designed for:control of the thermal state of traction electric motors (TED) as part of a high-speed traction-energy car-laboratory for testing rolling stock (TEL-C) in the acceptance and certification tests of electric locomotives;control of the thermal load of the TED and the temperature distribution by volume of the TED during the operational tests of electric locomotives;experimental determination of the most heated parts of the TED under different operating conditions;display of the current thermal state of the engine to the operator of the system;storing the thermal state data in the database for later playback.
