Showing results: 7531 - 7545 of 8512 items found.
-
Educated Design & Development, Inc.
1 Button Testing - No setup required, just plug right in!Digital LED display reads out in OhmsAlso performs the Low Current Ground Continuity test, at the same time!Auto Test Time (1 sec. / 60 sec.)+ - No need to set a timer or clock watchCustom universal receptacle accepts both 120V and 240V plugs.Zero feature allows you to "zero-out" the test lead impedance.Meets UL, CSA, CE, EN, IEC, MIL and all other international safety agency requirements.
-
MOS2 -
Holding Informtest
Mezzanine module (mezzanine) MOS2 is designed to convert instantaneous voltage values of an electrical signal into a digital code, measure instantaneous voltage values. The mezzanine is intended for use in HF and microwave systems as a terminal device for digitizing intermediate frequency signals up to 200 MHz. Together with the frequency converter DOWNCONVERTER 10 GHz LXI manufactured by the holding "Informtest" MOS2 under the control of the common software shell ACM2 makes up a synthetic instrument - spectrum analyzer, a ready-made solution for testing microwave devices and radio reception channels.
-
Rohde & Schwarz GmbH & Co. KG
To meet the measurement challenges of 5G device testing in the mmWave (mmW) frequency spectrum Rohde & Schwarz offers the R&S®CMPQ, a fully integrated solution from a single supplier. The R&S®CMPQ consists of the R&S®CMP200 radio communication tester, the R&S®CMPHEAD30 remote radio head and the R&S®CMQ200 shielding cube. The R&S®CMPQ provides accurate and reliable measurement results under radiated conditions.
-
RCDAT-30G-30 -
Mini-Circuits
Mini-Circuits’ RCDAT-30G-30 is a precision programmable attenuator covering an extremely wide bandwidth, from 0.1 to 30 GHz. Its unique design allows attenuation settings to be programmed from 0 to 30 dB, in 0.5 dB steps with monotonic attenuation change per dB, even at the highest frequencies and attenuation settings. The attenuator can be controlled via USB or Ethernet, allowing control directly from a PC, or remotely over a network. VHF / UHF / L / S / C / X / Ku / K band testing.
-
Crystal instruments
EDM Modal Sine Testing includes a dedicated test setup and operation process flow using a single or multiple modal shakers outputting a sine wave to acquire FRF signals. The Source Output type is either Swept sine or Stepped sine. The sweep mode can be linear or logarithmic. The FRF signals of each measurement DOFs with respect to defined reference DOF will be constructed. The output drive level can be defined to run the test under no control strategy, or the response of a control channel can be specified to run the test in a closed loop.
-
PG-38 -
GME Technology
Model PG-38 NTSC Pattern Generator can be use to quickly and easily troubleshoot, test, and align NTSC television. Features a wide selection of popular video patterns including Color Bars, Crosshatch, Dot, Staircase, Circle, Center Cross, Window, and Raster for accurate and comprehensive TV troubleshooting and testing. Supports both progressive and interlace scanning system. Composite video and S-Video output. RF video output on Channel 3 with 1KHz audio tone for audio troubleshooting. User friendly interface for easy operation.
-
Norland Products, Inc.
The Norland Fiber Visualizer is a unique instrument which simplifies installation and testing of fiber optic networks. This compact unit uses a 0.5 mW helium neon laser, with an ultra-precision optical adapter, to focus high intensity visible light into the core of a fiber optic connector. As the light travels down the fiber, a visible red glow is emitted anywhere discontinuity occurs. The Visualizer imitates on the visible level, what normally occurs in the invisible infrared spectrum,thereby allowing the end user to actually see any problems in the system.
-
M7100 -
Doble Engineering
The Doble M7100 High-Voltage Asset Analyzer is your complete solution for high voltage testing.With an intuitive design and dual high-voltage leads, the M7100 greatly reduces the number of ladder trips technicians are exposed to per job sometimes cutting the number to nearly one third. This significantly improves the safety and quality of field work by limiting exposure to the workforce and reducing errors.The M7100 automates multiple tests that were previously performed by several pieces of equipment. This can cut down testing time from seven hours to one and a half hours.
-
Interpower Corp.
The Interpower® International Power Source (IPS) provides a low-cost, convenient source of AC power at various operating voltages and frequencies found around the world (typically 110-240VAC/50-60Hz) which is important for testing any products that are exported. Output power is delivered through one of two ranges: Low range (10-138VAC) through a standard NEMA 5-20 socket and High range (10-276VAC) through any of the six standard international sockets so that products can be conveniently powered during development or just prior to shipment.
-
Aceonn Corp.
Aceonn can integrate your existing laboratory equipment to improve data reliability, repeatability and responsibility: Reliability comes from setting test equipment via electronic controls; minimizing human error; Repeatability ensures that all tests for every device is performed to the same exact specifications; Responsibility flourishes in an environment that utilizes state-of-the art test systems. Aceonn will streamline your laboratory’s testing process and make your business more efficient. There is no need to buy new test equipment, just a better communication system.
-
TE6-0707 -
Hangzhou Tonny Electric & Tools Co., Ltd.
*Used to locate hot circuits and troubleshoot primary circuits on all 6, 12 and 24 volt systems.*Suitable for a broad range of household, car, trucks, boats, trailers, vans, motorcycles, industrial and commercial uses..*Convenient screwdriver-type handle*Heavy Duty probe *Heavy plastic handle and insulated ground clipTesters light up to indicate testing result*Durably designed for a long service life.*Lights for easy visibility.*Heavy duty coil cord or straight cord (optional).*Materials: plastic/metal
-
2440 -
Photon Kinetics
The 2440 Launch Analyzer is the first fully automated test system for characterizing the optical power distribution of the light produced by VCSEL laser sources, multimode fiber test equipment and launch cords utilized in multimode fiber links. Built on over 20 years of experience testing the transmission and geometric properties of muitimode fibers, the 2440 is the ideal solution for ensuring that source launches comply with applicable international component specifications and measurement standards. The 2440 can be configured for measurements in either or both the 850 and 1300 nm windows.
-
PK-3456 Spy Splitpair -
Pansco, Ltd
Easily & accurately tests twisted pair cables for proper continuity and correct signal pair. A split pair can cause a crosstalk problem and suppress the communication speed. The SpySplitpair also includes a Full test, One-ended testing, Debug mode for checking the specific pair fault, and a Tone mode for tracing cable as well as a Voltage warning indicator to protect the tester. Hub blink/Net Tone mode (PK-3456E only), display of the Ethernet port to which the test cable is connected, and identify unknown RJ45 outlet for active Ethernet.
-
SIM-2FON-25 -
Virtual Console, LLC
Vconsole fiber optic network simulator is custom built portable unit intended to simulate installed fiber optic facilities. Vconsole will design and build custom unit exactly to customers specification. The enclosure is capable of housing an individual spool with up to 100km of fiber. We will build each unit to client unique needs with custom fiber types, lengths, and connectors. A full range of connectors are available including SC, ST, FC, and LC types. This product is ideal for latency testing, product development and training and educational needs.
-
KH3933 -
Beijing KeHuan Century EMC Technology Co,.LTD
KH3933 is a fully automatic interference field strength receiver integrating antenna and receiver. It is an important equipment for space field strength testing. It can be used to measure useless or harmful related radio interference signals in space, as well as medium wave and short wave. The field strength of the radio signal from a radio station. When measuring radio interference signals, this machine complies with GB/15707-1995 , DL/T691-1999 , and is suitable for high-voltage transmission lines and substation radio interference signals. This receiver complies with CISPR16-1 and GB6113-1 manufacturing standards.
