Showing results: 151 - 165 of 508 items found.
-
MM513 -
McGan Technology
McGan Technology’s MM513 electrosurgical insulation defect detector is a compact, hand held, battery operated unit that tests the integrity, such as pinholes, cracks or defects, of the insulation of electrosurgical instrument in order to prevent inadvertent tissue burns which may occur during electrosurgical instrument procedures. The integrity of the insulation of electrosurgical instruments can occur over time, through normal surgical use, through the accidental contact with a sharp instrument or the rubbing of the insulation to the point of abrading it. The insulation failure provides an alternate pathway for the current to leave the instrument’s electrode usually beyond the sight of the surgeon which will result in the unintended tissue burn. Using an electrosurgical test equipment maintenance program can greatly reduce the number of these inadvertent burns during electrosurgical procedures.
-
1260A -
Ametek Scientific Instruments
The model 1260A Impedance/Gain-Phase Analyzer is - without doubt - the most powerful, accurate and flexible Frequency Response Analyzer available today. In daily use by leading researchers wherever measurement integrity and experimental reliability are of paramount importance, the 1260A’s solid reputation is frequently endorsed in published research papers in fields.
-
GRL-KIT-DI20 -
Granite River Labs Inc.
The GRL Deep Inspection Kit (KIT-DI20) addresses the gap between expensive, challenging-to-use VNAs and simple functional/continuity tests that are not adequate for high speed interfaces. Now, users without years of signal integrity testing expertise can perform professional measurements with high accuracy to 20GHz with easy-to-use equipment.
-
HF Scientific
Ballast water is essential for safe and efficient shipping operations and stabilizing steel-hulled vessels at sea. It provides a variety of critical functions, such as maintaining balance, stability, and structural integrity on non-cargo voyages or when cargo is unloaded. Ballast water is also used to compensate for fuel and water consumption during at-sea operations.
-
Current-Voltage Measurement Option -
Materials Development Corporation
CSM/Win Systems with an I-V option can measure both MOS and diode structures. For junctions, both forwardand reverse bias curves can be analyzed. Junction ideality factor, series resistance, and reverse saturation current are found. Solar cells can be checked for efficiency. Gate Oxide Integrity of MOS devices can be measured as well.
-
TQC Ltd
Pressure testing involves applying stored energy to an assembly of parts, in order to verify its strength, its integrity and/or its functionality. Pressure Testing generally uses the application of a test fluid (liquid or gas) into a volume and the fluid is then pressurised to exert pressure forces onto the test object that can be measured.
-
Pulse Electronics
Pulse’s Ethernet transformers are RoHS compliant and qualified at major PHY suppliers. 100/1000/2.5G/5G/10GBASE-T Ethernet transformer modules are optimized for all major LAN transceivers. All modules provide electrical circuit isolation that meets IEEE 802.3, while maintaining signal integrity needed for the most demanding applications.
-
Safety IntelliPoint -
AMETEK Drexelbrook
The Safety IntelliPoint level switch provides a capacitance probe level switch with either a current output or relay contacts and “On-Board” self-diagnostics to ensure reliability. This SIL Intellipoint conforms to SIL 2 specifications providing the ultimate in level switch integrity and level sensing elements for a wide variety of temperatures, pressures, and materials.
-
BroadWave Technologies, Inc.
Impedance matching pads from BroadWave eliminate impedance discontinuity (mismatches) without introducing reflection to the circuit. Custom units are available in a variety of impedance and connector types from DC to 4 GHz. BroadWave Technologies impedance matching pads preserve signal integrity by matching virtually any transmission line.
-
Virginia Panel Corporation
VTAC Wired configurations reduce resistance and increase signal integrity with a seamless transition from wire to connector. This can be demonstrated in an example using the results of VPC quality and performance testing on VTAC patchcords. The results are reflected in the graph below. Insertion loss was tested on one-meter long patchcords with SFP+ terminations on either end. The second data line (red) shows the same patchcord, but bisected and terminated with VTAC connectors in its center. The results show no significant deviation from the SFP signal until approximately 6.25 GHz. Even at 6.25 GHz, there is only -1dB of difference between the two patchcords, which is approximately a 10% loss. With signal integrity playing such an important role in high speed testing, the obvious choices for high bandwidth data testing are VTAC Wired products.
-
UXR–B Series -
Keysight Technologies
Developing next generation technology requires world-class signal integrity from your test equipment. Achieve design insights you never thought possible with the highest bandwidth, highest ENOB, and lowest noise floor. Keysight’s breakthrough technology enables you to conquer even the most difficult measurement and design challenges.
-
SK2-SESSION -
ELMA Electronic, Inc.
SK2-SESSION is a bidirectional 4-lane PCI Express® Gen3 redriver, for optimum 8GT/s high speed signal integrity, and can be installed into any peripheral slot of a CompactPCI® Serial backplane.
-
RTA4000 -
Rohde & Schwarz GmbH & Co. KG
Designed with top class signal integrity and responsive ultra-deep memory, the R&S®RTA4000 brings the power of 10 to a new level. The Rohde & Schwarz designed 10-bit ADC plus class-leading noise and memory depth provides sharp waveforms, more accurate measurements and confidence when facing unexpected measurement challenges.
-
VME-196 -
Curtiss-Wright Defense Solutions
Our VME-196 combines the performance and the advanced I/O capabilities of the NXP quad-core AltiVec enabled T2080 processor. The VME-196 is supported by Curtiss-Wright’s U-Boot, Green Hills INTEGRITY, Lynx Software Technologies LynxOS, Yocto NXP SDK-based Linux and Wind River VxWorks 6.9 and 7 Board Support Packages (BSPs) and driver suite.
-
40-876-104 -
Pickering Interfaces Ltd.
The 40-876-104 is a 50 Ohm 4 to 1 RF multiplexer with 4 banks in a single PXI slot. Additionally, extra switching allows the common connection to be terminated into 50 Ohm, maintaining signal integrity. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.