Filter Results By:
Products
Applications
Manufacturers
RF Sensors
Detect RF signal and represent the detected signal level in a manner that can be measured and recorded.
See Also: RF Power Sensors
-
product
PXI-5650, 1.3 GHz RF Signal Generator
779670-00
The PXI‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
PXIe-5654, 10 GHz or 20 GHz RF Signal Generator
783126-01
The PXIe‑5654 features an ideal combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe‑5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications.
-
product
PXIe-5651, 3.3 GHz RF Signal Generator
PXIe-5651 / 781216-01
PXIe, 3.3 GHz, PXI RF Analog Signal Generator—The PXIe‑5651 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5651 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
PXI-5652, 6.6 GHz RF Analog Signal Generator
779670-02
6.6 GHz PXI RF Analog Signal Generator—The PXI‑5652 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5652 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
PXIe-5650, 1.3 GHz RF Signal Generator
781215-01
The PXIe‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
Flow Meter Sensor
RF Pickups
SPECTEC Innovative Sensor Solutions
SPECTEC RF pickups are excellent for applications that require near zero speed and zero magnetic drag sensing characteristics, such as flow meter sensor applications. SPECTEC RF (modulated carrier) sensors have a long history of use in turbine flow meters and turbine engines in the aerospace, petroleum, chemical, pharmaceutical and food industries.
-
product
On-Line Moisture Meters
Many methods are available for measuring moisture content on line, in real time: NIR, RF Capacitance, NMR (Nuclear Magnetic Resonance), and Microwave, among others. Finna Sensors is unique in that it has experience with most of these methods and is therefore able to recommend the best possible solution for any application.
-
product
RF & Microwave Power Meters
Our RF & microwave power sensors ensure precise and reliable measurements. They provide the highest measurement accuracy and speed, simple operation, technological leadership in thermal, diode and OTA core measurement elements as well as traceability to national standards.
-
product
RF Power Meter
PMX40
The PMX40 provides design engineers and technicians the utility of traditional benchtop instrument, the flexibility and performance of modern USB RF power sensors, and the simplicity of a multi-touch display built with Boonton award-winning technology.
-
product
RF Power Sensors
Providing the highest video bandwidth and fastest rise times, RTP5000 peak power sensors with Boonton’s Real-Time Power ProcessingTM deliver 100,000 measurements per second, no gaps in signal acquisition and zero measurement latency.
-
product
RF Power Sensor Solutions
Bird provides innovative power sensor solutions for all types of RF applications. From simple directional power sensors for the measurement of transmitter output power and VSWR measurement and monitoring applications, to highly accurate self correcting power sensors for process control applications, you can rely on Bird sensor products to meet the needs of your unique applications.
-
product
Standard RF Power Sensors
Coaxial Dynamics "Standard" line of RF Power Sensors provide DC currents proportional to the forward and reflected power flowing through the line. All models are designed to drive a 30A, 1400-Ohm meter, or provide approximately 100 millivolts across a 5K load.
-
product
Portable RF Analyzer
PMT-330
The Process Sensors Portable Moisture Tester (PMT-330) puts the capabilities of an on-line moisture analysis and control system into the palm of your hand, allowing operators to spot-check moisture content of boards, wood, plastic, and paper products quickly and easily. It features radio frequency dielectric (RF) measurement technology that penetrates the surface of products and instantly displays accurate moisture data.
-
product
SMART III RF Probe
Finna Sensors’ Smart III RF Moisture Probe is appropriate in those situations where NIR use on conveying systems/web applications or RF flat plate sensor use on board type products are not sufficient. Examples include tanks, bins, barrels, drums, Super Sacks™, silos, etc. These applications require a probe type moisture meter where the probe is inserted into, and is surrounded by product. Since the probe generates a 3 inch diameter radio frequency field around the length of the probe, a significant volume of product is measured. As the product is slowly removed from the silo, and refilled from the top, it passes by the RF Probe, thereby providing a constant real time moisture measurement. Typical applications would include starches, distillers and brewers grains, granulated chemicals or food ingredients, whole grains such as corn kernels, rice, soybeans, tree nut stockpiles, etc.
-
product
Process RF Sensors
Process RF (radio frequency) analyzers using penetrating radio waves to determine the moisture content across a full sample thickness. Single point, array and hand-held analyzers provide a variety of sampling options from fully integrated in-process moisture profiling to at-line quality control. RF analyzers are widely used in gypsum, panel board, and other industrial processes.
-
product
RF Peak Power Sensors
These sensors feature real-time processing and hardware triggering with advanced PC software to capture even the most elusive signals. Measure pulsed, bursted, and modulated signals used in commercial and military radar, electronic warfare (EW), wireless communications (e.g., LTE, LTE-A, and 5G), consumer electronics (WLAN and WiFi 6), as well as education and research applications.
-
product
Battery Module
BAT-200
The Battery module supplies power to a sensor, or chain ofsensors, operating in the Off-Line mode, and to sensors connectedto an RF communication module.The Battery module can be recharged by connecting it to the PC'sUSB socket via the USB module's USB cable.
-
product
RF Communication Module
RF-200
The RF Communication module allows remote operation of asingle sensor or a chain of sensors. The remote single sensoror chain is connected to an RF Communication module and to aBattery Module which powers them all.
-
product
Wattmeters
Monitor 4 sensors simultaneously for peak, Average power and coax SWR. Direct USB 2.0 full speed interface. Backlit LCD display for stand-alone operation- Your PC is optional. Oscilloscope and Spectrum Analysis of the RF Modulation- Observe IM and "Splatter" frequency components realtime. Complete system includes (1) sensor, WN-2 unit, AC power module and software on CDROM. Wide range of sensors cover 100 milliwatt to 8KW, 1.6 Mhz to 470 Mhz.
-
product
True Average Connected Power Sensors
CPS2000
CPS2000 True Average Connected Power Sensors provide USB, LAN and PoE capabilities to enable easy RF power measurement of modulated and CW signals from 50 MHZ to 8 GHz. Compatible with Windows and Linux systems, CPS2000 sensors include all the necessary drivers for programming through SCPI, IVI and LabVIEW. Connectivity and compatibility, combined with 60 dB dynamic range and 100 measurements per second, CPS2000 sensors are the ideal solution for lab, field, production test, ATE remote monitoring and embedded environments.
-
product
Semiconductors
Bird RF Laboratory Sensors have been depended upon for decades to provide highly accurate power measurement of laboratory and semiconductor production processes. Ranging from the 4020 Series sensors capable of 3% accuracy and the more advanced 4027 Series sensors capable of 1% accuracy. These highly accurate sensors have also been integrated into turnkey calibration carts that integrate all the components required to measure, display and dissipate power from RF delivery systems. Even more sophisticated systems, the VIP and BDS have been developed to not only measure voltage and current but also the phase relationships between them to enable a higher degree of insight into modern, complex semiconductor processes.
-
product
RF Power Sensors
Bird provides power sensor solutions for virtually all types of RF applications. From simple true-average power measurement applications to complex waveforms associated with today's modern communication systems.
-
product
Services
At Pure Engineering, we specialize in providing custom solutions to help our clients overcome their most challenging problems. Our services range from rapid prototyping to mass production of consumer products and are backed by our deep understanding of low power design, RF complexities, design for manufacturing, and product life cycles. Our team is skilled in a variety of areas, including strategic planning, product development, and architecture design. We use engineering principles to assess the feasibility and suitability of technology for a given design and can create proof-of-concepts, prototypes, and subject matter experts to solve design challenges. We also have expertise in the Internet of Things (IoT) and have experience developing low-power systems that run on batteries and efficiently transfer data. Additionally, we have extensive experience in Bluetooth Low Energy (BLE) technology, creating sensors that connect to modern phones and computers and creating custom protocols using off-the-shelf hardware. Whether you need help with a specific aspect of your project or support throughout the development process, we are here to assist you.
-
product
RF Power Sensors
Berkeley Nucleonics Corporation
an instrument, which can measure the electrical power mostly in the range of 100 MHz to 40 GHz.
-
product
mmWave Sensors
The world’s most precise millimeter wave sensor available today on a single chip. The world’s most precise millimeter wave sensor available today on a single chip. TI’s CMOS single-chip sensors integrate an RF front-end with a DSP and MCU.
-
product
Eddy Current Probes and Drivers
Proximity sensors work on the eddy current principle. A proximity system consists of an eddy current probe, extension cable and driver. A high-frequency RF signal is generated by the driver, sent through the extension and probe cables and radiated from the probe tip. The tip consists of a precision wound copper coil inside a chemical and temperature resistant PEEK case.
-
product
Low Cost RF Power Sensor Calibrator (100 kHz to 18 GHz)
1827
Calibrates 100 kHz to 18 GHz RF power sensors in 30 minutes or less; two Switchable RF inputs; Thermistor RF Power Standard is internally temperature controlled; Type IV Bridge Circuitry; DC Power Levels can be measured to within 0.003%.
-
product
Low Cost RF Power Sensor Calibrator (10 MHz to 18 GHz)
1825
Calibrates 10 MHz to 18 GHz RF power sensors in 30 minutes or less; Thermistor RF Power Standard is internally temperature controlled; Type IV Bridge Circuitry; DC Power Levels can be measured to within ±0.003%.
-
product
Power Sensors
N8480 Series
N8480 thermocouple power sensors, integrated with EEPROM capability, are the latest RF sensor applications with excellent measurement accuracy, repeatability, and linearity.
-
product
High Sensitivity ICP® Accelerometers
High sensitivity ICP® accelerometers are specifically designed to enable the detection of ultra-low-level, low-frequency vibrations associated with very large structures, foundations, and earth tremors. These sensors typically possess exceptional measurement resolution as the result of its comparatively larger size, which furnishes a stronger output signal and a lower noise floor. All units are hermetically sealed in a titanium or stainless steel housing. Models that include a 2-pin, military style connector provide the added benefit of being electrically case isolated for superior RF and EMI protection.
