Showing results: 2626 - 2640 of 2923 items found.
-
ACCAT -
Huntron
The ACCAT is designed to support diagnostic and acceptance test requirements across a wide spectrum of testing parameters. ACCAT provides a suite of core parametric test instruments, advanced GUI based software, Huntron Access Robotic probing and Huntron Analog Signature Analysis (ASA). ACCAT provides stimulus and asurement capabilities necessary for full functional and parametric testing of circuit card assemblies along with robotic guided probes for fault verification and debug. The Huntron ASA test is ideal for pretest or safe to power up procedures protecting the integrity of the test system.
-
IRU152-I -
Axiomtek Co., Ltd.
*RISC-based (i.MX 6UltraLite) processor 528 MHz*512MB DDR3 SDRAM onboard*8GB eMMC flash onboard*2 PCI Express Mini Card slots (Wi-Fi, 3G/4G or LoRa)*4 isolated analog input channels (16-bit, 250 kS/s, 0 - *20mA, ±20mA)*1 isolated COM port*1 isolated DIO (2-in/2-out)*Embedded Linux operating system (Yocto)*Wide operating temperature range from -40°C to +70°C*Supports LabVIEW versions later than 2016*Supports OPC UA
-
IRU151-I -
Axiomtek Co., Ltd.
*RISC-based (i.MX 6UltraLite) processor 528 MHz*512MB DDR3 SDRAM onboard*8GB eMMC flash onboard*2 PCI Express Mini Card slots (Wi-Fi, 3G/4G or LoRa)*4 isolated analog input channels (16-bit, 100 S/s, ±20mA )*1 isolated COM port*1 isolated DIO (2-in/2-out)*Embedded Linux operating system (Yocto)*Wide operating temperature range from -40°C to +70°C*Supports LabVIEW versions later than 2016*Supports OPC UA
-
NEBULA -
Intellitech Corp.
You, your vendors and your customers being able to use one common interface to control and observe on-chip IP, resources and instruments. The figure below shows an example IC. The new IEEE 1149.1-2013 standard supports an init-data register for configuring the analog paramaters of I/O as well as controlling on-chip PLLs. The standard further extends this by defining in BSDL user test data registers or 'scan chains'. These registers enable the ability of generic software to control and observe mission mode IP and instruments simply by describing the register interface in BSDL.
-
Analog Devices Inc.
Analog Devices DecDriver® family of digital LCD display drivers helps meet the increasing demand for higher resolution displays in home entertainment and home theater. This portfolio of products offers improved power, enhanced image quality, and lower costs, and has been optimized for a wide range of displays and performance needs. Our digital LCD display drivers operate over the commercial temperature range of 0°C to 85°C and include features such as a flexible digital input format that allow the devices to be used in parallel in high resolution displays.
-
Analog Devices Inc.
Analog Devices is an industry-leading provider of bipolar d/a converter solutions offering exceptional 1 ppm performance and optimized feature sets to ensure quick and easy deployment of bipolar converters across a range of end applications. With a comprehensive portfolio of bipolar DACs fabricated using proprietary iCMOS® process technology, ADI has enabled the development of high performance ICs at high voltage levels while simultaneously reducing package size and power consumption. By bringing together the many benefits of integration, ADI’s bipolar DACs reduce design time and system complexity.
-
Analog Devices Inc.
ADI integrated solutions combine both the D/A converter and driver in one chip to provide the required output directly from the digital domain. Analog Devices’ portfolio of leading industrial D/A converters and drivers provides a range of programmable output ranges from standard 4 mA to 20 mA for current loop communication to ±10 V for actuator control. ADI industrial converters offer considerable control functionality and advanced on-chip diagnostics to maximize system uptime, as well as eliminate the need for costly calibration routines needed by some traditional discrete architectures.
-
Dynamic Test Solutions
DTS has a full line of standard PIBs for all major tester platforms. Custom PIB designs can accommodate any test head, prober and manipulator configuration, including probe card changers, overhead direct dock setups and cable interfaces. DTS wafer test loadboards are compatible with a variety of pogo pin interface towers. All PIBs are constructed with impedance control, precision matched line lengths, full power and ground planes and both analog and digital resources to provide high quality signal integrity directly to the device.
-
PEAK gridARM Evaluation Board -
PEAK-System Technik GmbH
The ARM7 microcontroller gridARM™ was developed by Grid Connect® as a system on a chip solution (SoC) for the implementation of embedded applications with a focus on industrial communication. The Evaluation Board PEAK-gridARM is a Linux-based development platform for the gridARM™ microcontroller. It has connections for Gigabit Ethernet, high-speed CAN, USB 2.0, RS-232, SPI and I²C. The digital and analog inputs of the evaluation board can be manipulated with buttons and potentiometers. The states of the microcontroller, the supply and the message traffic are displayed via LEDs. A board support package for Linux enables access to the hardware resources of the PEAK-gridARM evaluation board.
-
DP-cPCI-1197 -
Data Patterns Pvt. Ltd.
DP-cPCI-1197 is a high-resolution signal-conditioning module that amplifies the signals from full-bridge based transducers. This signal-conditioning module is available on a cPCI module form factor. This module has four gain settings to accommodate a wide variety of sensor output voltages. In addition, this module has an adjustable excitation voltage to accommodate transducer excitation requirements.A high resolution sigma-delta ADC and variable gain amplifier forms the core of the signal conditioning system. Direct digital conversion and digital isolation ensures a better signal integrity in comparison with the conventional analog system.
-
LEON Fixture -
Konrad Technologies GmbH
The LEONFixture is the ideal ICT and ISP solution for small and cost sensitive applications. This manually operated test system combines optimal ergonomics with high performance, durability and precision, ensuring your investment over the long term. The LEONFixture features a test system integrated in a manual base fixture. The system is designed to be used with an Ingun ATS MA13 insert which could be customized by a lot of fixture houses all over the world.As part of the LEON Family, LEONFixture is based on the ABex platform which directly incorporates Konrad analog bus technology and PXI/PXIe in one chassis.
-
A2B®-Component-Tester -
NOFFZ Computer Technik GmbH
The Automotive Audio Bus (A²B®) is a bus developed by Analog Devices Inc. for infotainment systems in automobiles. It is increasingly being used in other applications such as AV conferencing systems. Typical A²B® -products are Hi-Fi amplifiers/speakers, head units, eCall systems, microphones, vibration/noise suppression units, actuators, or sensorsCommunication happens via a simple two-wire UTP (Unshielded Twist Pair) cable. All A²B® -components are connected in a master/slave architecture to form a network. The complexity of audio systems in these A²B® -networks is reduced, and with it the cost and weight.
-
microBlox -
Acromag, Inc.
Acromag's microBlox uB Series I/O modules offer a compact, high-performance solution for interfacing sensors and field devices with data acquisition systems. uB signal conditioning modules are ideal to isolate, filter, convert and amplify a wide variety of signal types for test, measurement and control systems. Just plug uB modules into 4, 8, or 16-channel backpanels in any mix for a high-density analog I/O interface. Channel-to-channel isolation provides optimal noise and surge protection from ground loops, spikes, and high common mode voltages.
-
DCHT -
Lectrosonics, Inc.
The DCHT portable digital stereo transmitter is designed for use in film and TV production as both a wireless audio link from a bag or cart system to cameras and as a portable IFB transmitter paired with the Duet digital wireless M2R receiver packs. The DCHT accepts two channels of mic or line level analog signals or an AES digital signal from a mixer and transmits to the receiver or receivers in a purely digital format. The digital architecture of the new DCHT is a third-generation design with specially developed, high-efficiency circuitry for extended operating time on two AA batteries.
-
C-Series -
MKS Instruments
The C-Series Mass Flow Controller (MFC) is a compact, fast-response model using a Micro-Electro-Mechanical Systems (MEMS) based flow sensor for non-corrosive gas applications. It is available in Full Scale flow rates from 50 sccm to 50 slm (N2 equivalent) with a control range from as low as 0.1% of Full Scale up to 100% of Full Scale and is also available as a flow meter. Analog (0 to 5 VDC) or digital (RS485 or Modbus TCP/IP) communications interfaces are available. Required power supply voltage is 24 VDC nominal.