Showing results: 106 - 120 of 224 items found.
-
410130114 -
Virginia Panel Corporation
ITA, i2 MX, EMI Backshell, with Cable Exit (Shell only, does not include front protective cover or modules)
-
E3001 -
Eastern-Optx
The E3001 / Microwave Delay Line is a high performance turnkey solution for radar and communications market. With three selectable delays the E3001 allows for ultra wide bandwidth, low loss, high isolation and immunity from EMI and EMP with time delays up to 100 msec at frequencies from 0.1 to 6 GHz.
-
E501 -
Eastern-Optx
The Eastern OptX Series E501 / Microwave Delay Line is a high performance turnkey solution for radar and communications market. The E501 allows for ultra wide bandwidth, low loss, high isolation and immunity from EMI and EMP with timedelays up to 250 usec at frequencies up to 18 GHz.
-
TRAVELING WAVE TUBES (TWTS), MAGNETRONS AND KLYSTRONS -
Communications & Power Industries
CPI TMD has been immersed in the research, design and manufacture of electron devices since its inception, delivering solutions into some of the most demanding applications to support its customers’ requirements. CPI TMD's tube engineering "DNA" extends back to EMI Electronics' high-power klystron developments during World War II. Since then, CPI TMD has been instrumental in many of the industry's major TWT, magnetron and klystron developments.
-
SnapTac® Series -
Smiths Interconnect
Smiths Interconnect's SnapTac® Seriess is a lightweight, robust, quick release miniature connector, featuring IP67 sealing and EMI shielding. The series is available in both circular (7, 13, 19 ways) and rectangular (12, 21, 30 ways) styles. They are equipped with Hyperspring contacts, designed to protect the electrical interface against extreme environmental conditions.
-
Com-Power Corporation
A typical emi emission test is performed using broadband EMC antennas such as biconical, log periodics, Combilogs and horns. These antennas usually placed at 1, 3 or 10 meter distance as required by the test specification. These is considered far field measurements and the emission limits are given for the specific distance by the specification. During EMI compliance measurements, the emissions levels from products are compared with these limits. If the product exceeds these limits it is considered failing. These tests are typically conducted in a open area test site IOATS) or inside an anechoic chamber.
-
FOTEMP1-OEM-MNT -
Micronor AG
The FOTEMP1-OEM-MNT is a small form factor PCB interface module designed for low cost insertion of high precision GaAs-based fiber optic temperature sensor technology into OEM applications where common electrical temperature sensors and thermocouples cannot be used. The OEM interface product is compatible with all TS series fiber optic temperature probes. The sensors are entirely non-metallic and electrically passive, providing immunity to EMI, RFI, MR, microwaves and radiation is required.
-
Schwarzbeck Mess Elektronik
Calibration-Pulse Generatoracc. CISPR 16for Band A, B, C, D(9 kHz-1000 MHz)To calibrate the pulseresponse of EMI receivers.Pulse repetition frequency main generator 0.1 - 200 Hz (aux. generator up to 1 MHz) with IEEE-488 Interface.
-
AFJ Instruments
High accuracy CISPR 16-1-1 EMI receivers and high precision calibrated antennas for radiated emission measurements.
-
-
Teledyne Marine Cable Solutions
Shielding Types• Braided I Served I Spiral• Foil & Hybrid• Vapor Barriers• Copper & Alloys• Conductive & Static Dissipative Tapes• Conductive Fabrics• Tensile Members• RFI & EMI Tapes & Braids (Serveor Interwoven)• Utilizing Flat & Round Copper• Stainless Steel• Bronze• Aramid Fibers & Textile, amongothersConstruction• Multi-conductor, shielded pairs, pairs with steel tubed fiber or copper conductors with fiber optics, coaxial conductors & aramid strength fibers
-
8282-1 -
Solar Electronics Company
The Model 8282-1 Transient Pulse Generator was designed for screen room use in making conducted spike susceptibility tests. It provides all the waveshapes required by MIL-STD-461B/C and many other military EMI specifications
-
VOL-PBE -
Lisun Electronics Inc.
• EMI Receiver equipped with voltage probe can test disturbance voltage from load terminals or control terminals
-
Schwarzbeck Mess Elektronik
In addition to EMI measurement with LISNs (Line Impedance Stabilisation Networks, Artificial Mains Networks), Probes are used for Terminal or Line voltage measurement.LISNs are required to feed the Equipment under Test (EuT) with mains power, to reduce external line interference, to offer the EuT a standardized impedance and to route the extracted r.-f. voltage to the EMI receiver.
-
CUS1500M Series -
TDK-Lambda Corp.
*Low Audible Noise (<45dBA)*EN55011/55032-B EMI*Enclosed compact construction*Medical and Industrial Certifications*7 year warranty