Showing results: 2386 - 2400 of 3098 items found.
-
Analog Devices Inc.
Analog Devices buffered video crosspoint switches offer multiple configurations from 8x8 up to 32x32 channels with gain of 1 or 2 and are offered in LQFP, LFCSP, and BGA packages. These crosspoint switches can be programmed either in serial or parallel modes and are used primarily for routing high speed signals, including composite video (NTSC, PAL, SECAM) and component video (YUV, RGB) in applications such as studios, video on demand, in-flight entertainment, surveillance, and video teleconferencing.
-
RPT-AAA Series -
Ripley Tools LLC
Electronic testing tool designed to check the circuit integrity in new or installed cable up to 5,000 feet (1,500 meters) in length LED indicates DC shorts, splitters & other self-grounding devices in cable while a loud audio tone identifies the line carrying the signal Equipped with a right angle male push-on connector to maneuver in tight areas & a female push-on connector for speed toning Tool includes a pocket clip & (1) AAA 1.5V battery.
-
34XX -
FETservice, Inc
Performs DC, AC, and pulsed tests. Excels at evaluating difficult to measure parameters on zeners, current limiters, varactor tuning diodes, darlingtons and matched dual transistors. 24 bin opto-isolated handler/prober interface. Parallel first-in first out computer to tester interface for maximum throughput. Parallel testing with a 3402E or 3403E allows shared test execution for extremely high throughput applications when interfaced to high speed handlers with multiple test sites.
-
INFRASONITUS -
BioAge s.r.l.
The infrasonic signal, acquired by a suitable microphone, is filtered by an active low-pass filter of the fifth order with a cut-off frequency at 20 Hz, with low noise, then it is sampled and acquired by a 16-bit ADC with a speed of 50 samples. / sec. The amplification factor can be set to 0.1 / 0.5 / 1/10.The infrasonic monitoring system includes a complete diagnostic functionality that performs an exhaustive functional test without the use of other tools: this function is extremely useful when the system is installed on the volcano at high altitudes.
-
Analog Devices Inc.
Analog Devices’ portfolio of low noise (≤ 10nV/√Hz) op amps includes many amps with the lowest noise performance in the industry. These high speed, low distortion (1 nV or less) op amps enable better signal fidelity in the most demanding conditions, allowing system designers to achieve the lowest total system noise performance in applications with high source impedances. We feature a considerable variety of these amps with wide supply ranges and low power.
-
PLGA-1000 -
HORIBA, Ltd.
The PLGA-1000 Process Laser Gas Analyzer is designed to measure hydrocarbons and other gases contained in process gases at petrochemical plants. The PLGA-1000 uses proprietary technology to measure low concentrations of acetylene (C2H2) and carbon dioxide (CO2) contained as impurities in high concentration methane (CH4) and ethane (C2H6) which are material gases, continuously at high speed and with high sensitivity . This contributes to improvements in productivity, cost, and quality in the manufacturing process, as well as reducing environmental impact.
-
Smartech Inc.
• Inductive measuring probes specially designed for measurement by comparison• Available in 2 versions: spring push and pneumatic push• Long life precision bearing guidance (tested up to 13 million cycles)• Resolution <0.0001 mm• Repeatability 0.15 μm• Measuring range +/- 2mm and +/- 5 mm• Compatible with D300SV2, D70i and D400S units through M-Bus multiplexer units• High data speed• Operating temperature +10 to +80°C• IP65 protected
-
MaxLinear
PowerArchitect™ design and configuration software speeds development and significantly reduces overall time-to-market compared to legacy analog power solutions. An I²C interface and multiple GPIO pins ensure easy system integration. Configurable warning and fault levels, fault behavior and power up and down sequencing ensure any load can be properly powered and protected. The power system design can be completed with confidence long before the final revision of the SoC or ASIC is available.
-
Ultraview Corporation
Ultraview''s PCI data acquisition add-in cards are complete data acquisition (A/D) and control (D/A) systems on a single PCI Bus card. Ranging in speed from dual 14 and 12-bit 1-25MSPS boards up to 1500MSPS 8-bit boards with 8GB/16GB of on-board RAM. All cards come with graphical waveform viewers, example user programs (source code included) and device drivers for Linux or Solaris, allowing users to quickly prototype and develop their applications.
-
KD-2446 -
Kaman Fuzing & Precision Products
* Outstanding precision: static resolution to 12 microinches* Excellent performance with ferrous targets* Variable voltage input from 12 to 24 volts DC* Compact rugged electronics and sensors* Adjustable gain for up to 22 volts output (with 24 Vdc input)* Temperature tolerant sensors (to 400°F)* High speed (10 KHz) level adjustable switched output for process control* Very low switching hysteresis, < 1% on ferrous targets* RoHS compliant
-
SPIDAR® -
Sensors and Software Inc.
User interface and data acquisition embedded on the NIC:1. Any device with Wi-Fi can be used to change settings or view data collection2. No data collection interruption or data loss occurs if connection to PC or device is interrupted. No reduction in speed compared to running a single system. Daisy-chain NICs to deploy any number of GPR systems simultaneously; build Multi-frequency systems or Multi-channel Array systems Advanced timing control to ensure no interference between GPR systems
-
WT Dyno -
HORIBA, Ltd.
Our WT series eddy current dynamometers are mainly used in the development and testing of all types of prime mover, as well as various engine assemblies. Due to their robust design, which incorporates improved control characteristics, they can be used both as steady state and as transient test stands.Their high speeds for automobile engine testing and their optimised cooling chamber, are convincing arguments that speak for themselves. All WT type dynamometers are suitable for operation in both directions of rotation.
-
IQxel-M -
LitePoint Corporation
The new LitePoint IQxel-M™ Bluetooth Advanced measurement system is a major advancement in the speed and efficiency for performing over-the-air testing of Bluetooth Low Energy peripheral and beacon devices. Using LitePoint’s proprietary measurement techniques, testing Bluetooth devices has been made simple and the system performs comprehensive transmitter and receiver measurements in a matter of seconds. The solution is optimized for both engineering and manufacturing and works with all BLE peripheral and beacon devices, regardless of chipset.
-
IMADA, Incorporated
Imada offers manual and motorized wire crimp test systems in either vertical or horizontal configurations.Lever-operated systems offer basic functionality and rapid destructive testing up to 220 lbf.Motorized systems have speed control and are capable of destructive or force-controlled non-destructive testing up to 1100 lbf.Choose from manual or automatic wire-gripping fixtures.Digital gauges offer data output for analysis with data acquisition software.Create your own custom configuration or consult our application specialists.
-
HyPix-3000 -
Rigaku Corp.
Rigaku’s HyPix-3000 is a next-generation two-dimensional semiconductor detector designed specifically to meet the needs of the home lab diffractionist. One of the HyPix-3000’s unique features is its large active area of approximately 3000 mm² with a small pixel size of 100 μm², resulting in a detector with high spatial resolution. In addition, the HyPix-3000 is a single photon counting X-ray detector with a high count rate of greater than 10⁶ cps/pixel, a fast readout speed and essentially no noise.
