Showing results: 526 - 540 of 3098 items found.
-
Apposite Technologies llc
Linktropy Emulators Provide Affordable Network Emulation for Accurate, Repeatable Performance Testing at Speeds up to 1 Gbps
-
-
PX773x -
VX Instruments GmbH
The PX773x is a high precision, high speed source and measurement unit, which is designed for automated high throughput testing.
-
ADLINK Technology Inc.
Significantly reduce over-all development costs, come with extended operating lifecycles, and speed up critical time-to-market.
-
ERAVANT
A ranging sensor head that is designed and manufactured for short range measurements of a moving or stationary target's range, speed and direction.
-
Ektron Tek Co., Ltd.
PL-2000X Plunger Testers equipped with servo-hydraulic system to control the testing speed. Available for customers to select suitable model.
-
MP5010 -
Chroma ATE Inc.
wi-fi, Bluetooth, GPS test capabilities in one box, high speed production tester for mobile communication devices.
-
UIO-4036 -
Advantech Co. Ltd.
*Supports 10/100/1000 Mbps Auto-Negotiation*2 LEDs on Each Port to Show Link/Active Status and Transmission Speed
-
8541C -
Spanawave Corporation
The Spanawave/Giga-tronics 8541C Single Channel Universal Power Meter combines accuracy, speed, range and measurement capability.
-
8542C -
Spanawave Corporation
The Spanawave/Giga-tronics 8542C Dual Channel Universal Power Meter combines accuracy, speed, range and measurement capability.
-
Omron Industrial Automation
The speed and precision of Omron's Articulated Robots robot makes them ideal for operations requiring fast and precise automation.
-
Keysight Technologies
The dedicated Current Sensors measure from 100 pA level dynamic current up to 10 A with a maximum of 200 MHz bandwidth. The mainframe acquires the signal from the sensors by a maximum of 1 GSa/s sampling speed and 14-bit and 16-bit wide dynamic range. This combination allows you to measure quite wide range of dynamic current, for example, from standby/sleep state to active state, at a single measurement. In addition, the wide bandwidth and the high speed acquisition enable you to measure high speed pulse response even less than 100 ns previously very difficult with existing instruments.
-
Shenzhen Graigar Technology Co.,Ltd.
Measurement of the speed of a rotating shaft is a common requirement in many industrial and laboratory applications. Such measurements have usually been carried out in the past with the help of contact type tachometers with friction drive. More recently digital optical non-contact tachometers have been designed which count the reflected pulses from a white patch on the shaft and then display the speed in rpm. The light source is usually a filament lamp operating with dry cells leading to limited life and illumination. A similar ideawith magnetic pick-up from a particular area of the shaft has also been used for speed measurement.
-
0149-QX -
Strobe Data Inc.
Quad+ speed Windows/NT Kestrel Co-Processor for four times the speed of the Kestrel /SX. Occupies one PCI slot. A writable control store, FPGA implementation of the HP1000 architecture with 4 MBytes of tightly coupled, zero wait-state memory. Includes compatible hardware floating point. On-card x86 microprocessor rapidly processes "virtual" I/O instructions. PCI bus speeds increase disk throughput by at least a factor of ten. HP1000 Bus support logic for non-emulated devices is provided on-board with connector to wide bandwidth fibrechannel adapter. Operates only under Windows/NT. WNT Support license included.
-
S-104 -
Notice
1 X 4 Switch slot module of FOTS system carries out the switching function that enables a single channel input to go to any of 4 outputs or a selected particular channel of 4 inputs to go to a single channel output. And its MEMS type switch module is bidirectional and transparent to signal format. It is remarkable that high speed switching and various driving program such as timed, manual or sequential switching mode are available through the combination of high speed response time switch and high speed FPGA processor. On the basis of less than 1ms switching time and 10ms minimum switching, high speed sequential switching can be installed easily by defining switching order, interval time and duration. Current switching channel status can be checked through LED fronted with slot, and present driving condition of optical switch can also be monitored through GOI or LCD monitor.