Showing results: 286 - 300 of 699 items found.
-
AP031 -
Teledyne LeCroy
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
Direct Dock -
Nidec SV Probe Pte. Ltd.
Direct dock style wafer probing allows for a higher bandwidth, increased pin density and testing more devices in parallel. Direct dock probe cards also support the growing movement of traditional final test to wafer probe which allows for known good die (KGD) and reduced cost of ownership.
-
1965 -
Peaceful Thriving Enterprise Co Ltd
*Pocket clip.*Bright LED indication.*No test leads required.*Screwdriver voltage probe.*Check voltage on 12-440V AC.*With UL and RoHS Approval.*Two LR44, 1.5V batteries included.*Tests for voltage, continuity and polarity.
-
Criterion Instruments Limited
PORTABLE OIL TEST. Test voltage rises up with 3 different speeds. Interchangeable oil cups sit in cradle contacts inside a test chamber with safety high-voltage interlock and hinged grounded metal lid with 2 windows to see the arc across the probes.
-
UWE Electronics
A lot of companies build test sockets. But only our test sockets are populated with our own proprietary probe technology, developed internally. This assures you that when you purchase one of our test sockets, you are using the most advanced interconnect available.
-
VC43™/VC43EAF™ -
Celadon
VC43™/VC43EAF™ probe cards offer a larger format version of the popular VC20. In addition to saving time, another advantage of the modularity is the ability to leave the interface in place and simply install the VC43™ topside using Celadon’s twist and lock insertion tool which minimizes the possibility of triboelectric or interconnect issues that can occur during typical probe card changes. The VC43™ can be used for production parametric test, modeling, characterization, and wafer level reliability testing. Cards can be configured up to 104 probes in either single or dual layer with near vertical probes to minimize scrub lengths on pads allowing the VC43s to probe pads as small as 30 microns.
-
Aerodyn Engineering, Inc.
AEI offers industry leading aerothermal rake and probe design and manufacuring. Aerodyn's unique combination of extensive in-house capabilities and close-knit structure allows challenging and time pressured rake and probe jobs to be handled. AEI welcomes anything from simple make-to-print jobs to elaborate design/fabricate/proof test projects.
-
A.T.i. Software GmbH
Analog components (resistance, capacitance, inductance, diodes, transistors, etc.) as well as complex digital components can be tested in the ICT. Compared to other test methods (e.g. flying probe), the in-circuit test enables very short test times (= high assembly throughput) combined with a very high test coverage.
-
ICE1 -
Langer EMV-Technik GmbH
The IC Test System was developed to measure the EMC behavior of circuits (ICs) in the event of targeted field or line-related interference and for measuring emissions. The test IC is tested in function. The test environment ICE1 creates the functional environment of the test IC. The respective measurement task is carried out with the corresponding probe set.
-
TBCP2-250 -
TekBox Singapore Pte. Ltd.
The TBCP2-250 is a snap-on RF current monitoring probe. The probe has a very flat response with a 3dB bandwidth of 250 MHz and is characterized over the frequency range from 30kHz to 300 MHz. Upon request, it can also be supplied with a test protocol covering the frequency range 1 kHz to 350 MHz. The aperture of the RF current monitoring probe is 32 mm. Its transfer impedance is > 12 dB Ohm in the range from 700 kHz to 300 MHz.
-
85024A -
Keysight Technologies
85024A high-frequency probe makes it easy to perform in-circuit measurements. An input capacitance of only 0.7 pF shunted by 1 megohm of resistance permits high frequency probing without adversely loading the circuit under test. Excellent frequency response and unity gain guarantee high accuracy in swept measurements with this probe. High probe sensitivity and low distortion levels allow measurements to be made while taking advantage of the full dynamic range of RF analyzers.
-
Staubli Group
This product range includes passive high-frequency test probes and accessories as well as touch-protected BNC plug connectors, insulated BNC panel-mount sockets, leads with RG58 or RG59 cable, adapters and converters. Our test probes are suitable for use in CAT III- and CAT IV environments (Measurement Categories), such as the analysis of house and building installations with mains analysis/mains monitoring devices. Our high-frequency accessories are designed with clearance and creepage distances in accordance with IEC/EN 61010-031.
-
5900 SERIES -
Probe Master Inc.
Probe Master's new 5900 series passive oscilloscope probes are available in 400 MHz & 500 MHz bandwidths. Probes are also available with readout actuators for oscilloscopes with the readout feature. The "GOLD PROBE" has been designed specifically for use with Tektronix, Hewlett Packard and other high performance oscilloscopes. This new slim design along with a host of versatile accessories, allows you to reach the most difficult test point in today's highly complex circuitry. The gold plated Probe Tips, Sprung Hook, Ground Lead, Alligator Tip and other critical interconnect points within the Gold Probe, provide excellent contacts for probing low level analog signals and high speed digital data. Unlike most "off shore" commodity probes, Probe Master guarantees quality and continuing domestic support for our "Made in America" Gold Probe.The probe body is made of high impact ABS. Soft molded strain reliefs at all stress points assure long cable life. In short it has been designed to offer you high performance coupled with high quality.
-
AMETEK Sensors, Test & Calibration
Our comprehensive range of grips, fixtures, jigs and probes cover most test applications within a wide range of industries. Below you will find a selection of our most popular grips, fixtures, jigs and probes. If you cannot find what you are looking for, please contact us for a presentation of our full range.
-
Bierer & Associates, Inc
A unique tool in that it may be used as a conventional phasing meter, or the meter probe may be used as a stand-alone voltage detector on primary or secondary voltages or capacitive test points.