Showing results: 46 - 60 of 276 items found.
-
34134A -
Keysight Technologies
Measure a wide range of applications with this battery-powered, clamp-on probe; use with DMMs or voltmeters
-
CP 35 -
GMC-I-PROSyS
The CP 35 current probe has been designed for use with oscilloscopes respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.
-
CWTMini50HF -
Power Electronic Measurments Ltd
For high-speed and high power-density power electronic applications. This higher bandwidth probe is ideal for measuring the faster current transients in today’s new semiconductor technologies where faster turn on and turn off times, higher blocking voltages and smaller circuits demand, smaller, higher temperature, faster current probes.
-
Extech 382098 -
Extech Instruments Corporation
Extech's 382098 is a set of 3000 A Flexible Current Clamp Probes for the model 382095 and 382096 power analyzers. Comes with three flexible AC probes that are 610 mm (24 in) long for wrapping around busbars.
-
TBCP2-250 -
TekBox Singapore Pte. Ltd.
The TBCP2-250 is a snap-on RF current monitoring probe. The probe has a very flat response with a 3dB bandwidth of 250 MHz and is characterized over the frequency range from 30kHz to 300 MHz. Upon request, it can also be supplied with a test protocol covering the frequency range 1 kHz to 350 MHz. The aperture of the RF current monitoring probe is 32 mm. Its transfer impedance is > 12 dB Ohm in the range from 700 kHz to 300 MHz.
-
P02-802 -
The Eastern Specialty Company
The TESCO High Voltage Non-Contact Current Probe (Catalog No. P02-802) was developed using current sensor technology. It is a two-piece, True RMS ammeter with a fiber optic link between the high voltage sensor and the readout at ground potential. The sensor is mounted on a hotstick and slipped over a high voltage line.
-
Extech PQ34-30 -
Extech Instruments Corporation
The Extech PQ34-30 is a set of 3000 A Flexible Current Probes for PQ3450/PQ3470 power quality analyzers. It has a 61 cm (24 in) length for wrapping around bus bars and wire bundles. Switch between 3 ranges: 3000 A, 300 A, and 30 A.
-
CP 305 -
GMC-I-PROSyS
The CP 305 current probe has been designed for use with oscilloscopes respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.Using advanced Hall Effect technology the CP 305 can measure currents accurately up to 450A peak over the frequency range of DC to 20 kHz.
-
EFX6000 -
Summit Technology, Inc.
The EFX6000 is a flexible AC current clamp utilizing the Rogowski principle. It can be used to measure currents from 1 amp to 6000 Amps in 2 auto-ranges, over a wide frequency range to 10kHz. The flexible and lightweight measuring head allows quick and easy installation in hard to reach areas, around large conductors and where access to confined or tight spaces is a problem. It requires no batteries or external power supply.
-
ACP1000 -
Shenzhen Micsig Instruments Co., Ltd.
*Test Current Range: 0.1A-1000A*Operating Frequency: 10Hz-100kHz*Maximum Primary Current: 2000A (2s)*Output Signal: mV/A*Highest Precision: 1%
-
CP2100 -
Shenzhen Micsig Instruments Co., Ltd.
*Split design, small and exquisite appearance, easy to test *Compatible with all BNC-connected oscilloscopes, adapters can also work with multimeters.
-
FAD-100 -
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Long Time Record of Measurement by Input Power Supply・Detection of Both AC Current and DC Current At Once・Detection of Small DC current Inside Large AC Current・Freely Bending with Flexible Clamp Sensor of Inside Diameter 200mm・Useful for difficult Access Locations with Wide Ranges up to AC/DC 1000A
-
Extech PQ3210 -
Extech Instruments Corporation
The Extech PQ3210 is a set of three flexible 1200 Amp flex clamps for the Extech PQ3350 3-Phase Power and Harmonics Analyzer. These probes are 304 mm (12 in) long for wrapping around busbars.
-
Extech PQ3220 -
Extech Instruments Corporation
The Extech PQ3220 is a set of 3000 Amp flex clamps (set of 3) for the PQ3350 analyzer. Probes are 61 cm (24 in) for wrapping around bus bars.
-
HA1000 -
Summit Technology, Inc.
The HA1000 is our most accurate current probe. The HA1000 clamp-on current probe measures from 1 to 1000 amps AC.