Showing results: 1666 - 1680 of 2878 items found.
-
LatticeXP2 -
Lattice Semiconductor
*Up to 885 Kbits sysMEM™ embedded block RAM and up to 83 Kbits distributed RAM*sysCLOCK™ PLLs up to four analog PLLs per device that enable clock multiply, divide and phase shifting*Three to eight sysDSP blocks for high performance multiply and accumulate.*Pre-engineered source synchronous IOs for DDR/DDR2 up to 200 MHz and 7:1 LVDS interface support up to 600 Mbps*Available in csBGA, TQFP, PQFP and BGA packaging
-
Model 20/20C-HS -
TREK, INC.
The Model 20/20C-HS is a DC-stable, high-speed, high-voltage power amplifier used in industrial and research applications. It features an all solid- state design for high slew rate, wide bandwidth and low noise operation. The four-quadrant, active output stage sinks or sources current into reactive or resistive loads throughout the output voltage range. This type of output is essential to achieve an accurate output response and high slew rate demanded by a variety of loads such as highly capacitive or reactive loads. It is configured as a non-inverting amplifier.
-
Model 10/40A-HS -
TREK, INC.
The Model 10/40A-HS is a DC-stable, high-speed, high-voltage power amplifier used in industrial and research applications. It features an all-solid-state design for high slew rate, wide bandwidth and low-noise operation. The four-quadrant, active output stage sinks or sources current into reactive or resistive loads throughout the output voltage range. This type of output is essential to achieve an accurate output response and high slew rate demanded by a variety of loads such as highly capacitive or reactive loads. It is configured as a non-inverting amplifier.
-
OEwaves, Inc
Laser houses a proprietary driver/controller and the OEwaves laser source which is based on a high quality factor (Q) Whispering Gallery Mode (WGM) micro-resonator. The laser is scalable to a variety of wavelengths in 370 – 4500nm. laser leverages the self-injection locking capability of a suitable commercially available laser diode via resonant optical feedback from a high-Q WGM micro-resonator. Its monolithically integrated approach along with micro-scale mass and volume make the laser virtually insensitive to environmental vibrations.
-
Masterclock
The Masterclock NTP100 family of NTP time servers provide accurate timing to networks and conform to NTPv2 (RFC 1119), NTPv3 (RFC 1306) and NTPv4 (RFC 5905). Each NTP100 device can operate on a local area network (LAN) or act as an enterprise-wide source for legally-traceable time and date distribution, depending upon your network configuration requirements. Masterclock NTP time servers are compatible with IPv4/IPv6 networks and offer AES256 SSH encryption, as well as MD5 authentication, for secure communications.
-
OMM-6810B -
Newport Electronics
The OMM-6810B is a power and wavelength meter capable of simultaneously measuring the optical power and wavelength of a laser source. A wide variety of measurement heads cover wavelength ranges from 350 to 1650 nm for power ranges of up to +40dBm or 10W.This meter has standard features such as logarithmic or linear display modes, auto ranging, user calibratable offset, reference measurement capability, analog output and IEEE-standard GPIB interface to make this instrument a cost effective laser diode development or production test tool.
-
NGM200 -
Rohde & Schwarz GmbH & Co. KG
Thanks to their high accuracy and fast load recovery time, the R&S®NGM200 power supplies are perfect for challenging applications. Their two-quadrant architecture allows them to function both as a source and a sink to simulate batteries and loads. Their short recovery times enable them to handle fast load changes that occur, for example, when mobile communications devices switch from sleep mode to transmit mode. High-speed data acquisition and convenient battery simulation widen the range of applications.
-
Orbit Controls AG
Orbit Controls process controllers are designed for direct connection to virtually all industrial sensors and signal sources. They can be used as process monitors to display the process variables to be measured or as process controllers to monitor processes. In addition to the digital display, the devices also have data interfaces, analog outputs and set point outputs. Simple process monitors are optimized in the factory for the desired measuring range and function at the customer's request. The programmable controllers can be parameterized on site via the keyboard or the data interface.
-
Trend Viewer -
ZETLAB Company
A trend is a diagram facilitating analysis of long records of measured sensor values (for hours, days, months, years). Based on the sampling frequency, an n number of counts per second are performed, and their yearly number equals to 31,556,926*n. If the user needs to evaluate short-term moments of the source signal, then there is no difficulty. It is much more difficult, when it is necessary to evaluate the parameters for the entire year or several years, and no monitor and no person would handle it. And this is the case when trend building could help.
-
Model 2313 -
ICS Electronics
* Provides 128 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Separate headers for RS-232 and RS-485 signals. * Optional 2313 Flat Ribbon Cables mount DE-9 male or female connectors on the rear panel. * Optional Relay Driver boards with 64 or 128 Relay Drivers.
-
1L20_CP3 -
SiTek Electro Optics AB
The SiTek Standard PSD (Position Sensing Detector) has high resolution, fast response and outstanding linearity. It is used in a wide variety of applications, most of them utilizing light sources in the visible or near-infrared part of the spectrum. The spectral range covers the region 400 - 1100 nm. Thanks to SiTek's proprietary AR-coating, optimized around 860 nm, a reflection loss of only 2% is achieved around the responsivity peak. Most of the detectors have a cover window to avoid handling damages.
-
Optosolar GmbH
This type of solar simulator uses Xenon high pressure arc lamps as light source. These lamps have a colour temperature near 5800 K, so it is feasible to filter the light output to an excellent AM 1.5 spectrum. If a tuneability of the spectrum is required, these lamps can be combined with tungsten lamps to achieve multi-source solar simulators. These can be used to measure tandem/triple/multijunction solar cells. They also allow detailed analysis of all types of solar cells using a spectral metric (see : Publication List).
-
521 -
ACO Pacific, Inc.
Accepted internationally 1 kHz represents the "0 dB" reference point of A, B, C Weighting and other filters utilized in acoustic measurement. The Pistonphone - a mechanical sound source - offers a slightly higher degree of accuracy at a substantial increase in cost. In addition, the 200 or 250 Hz operating frequency is mechanically limited and not suited for measurements of filtered inputs. The 0.2 dB accuracy is quickly lost in the 0.7 to 1.5 dB tolerances acceptable for weighting filters at frequencies around 250 Hz.
-
511E -
ACO Pacific, Inc.
Accepted internationally 1 kHz represents the "0 dB" reference point of A, B, C Weighting and other filters utilized in acoustic measurement. The Pistonphone - a mechanical sound source - offers a slightly higher degree of accuracy at a substantial increase in cost. In addition, the 200 or 250 Hz operating frequency is mechanically limited and not suited for measurements of filtered inputs. The 0.2 dB accuracy is quickly lost in the 0.7 to 1.5 dB tolerances acceptable for weighting filters at frequencies around 250 Hz.
-
IMI Inspector Alert™ V2 -
International Medcom
The IMI Inspector Alert™ V2 measures alpha, beta, gamma and x-radiation using a 2-inch “pancake” GM detector with high sensitivity to common beta and alpha sources. The easy-to-read digital display shows readings in your choice of µSv/hr, mR/hr, CPM, or CPS. The Total/Timer feature allows timed readings from one minute to 40 hours for precise measurement of low level contamination. An audible alert sounds when the radiation reaches a user-adjustable level.