Showing results: 2431 - 2445 of 2878 items found.
-
MPI Photonics Automation
Since 2008, MPI’s LED tester has provided optical and electrical measurements. With mass production experience, tester functions include flexible recipe management, accurate calibration, and statistical analysis. Flexible configurations allow the customer to choose test equipment configurations from the spectrum meter, photo detector and source measurement unit in accordance with your specific requirements. With accurate controlling of each instrument and intelligent data analysis, our testers offer the most accurate measurement result for a wide variety of optical devices.
-
Alpha Lab, Inc.
The Line EMI Meter measures electromagnetic interference in a single-phase AC power line. It plugs into a wall outlet (mains socket) and requires no battery. It immediately displays total line noise in millivolts (range 1999 mV, resolution 1 mV) in the frequency range 10 KHz 10 MHz (the frequency limits at which sensitivity is of the maximum sensitivity). A speaker plays the sound of the EMI, amplitude demodulated, in order to identify the EMI source (such as an AM or shortwave radio station vs. a motor vs. an electric arc).
-
Crystal instruments
EDM Modal Sine Testing includes a dedicated test setup and operation process flow using a single or multiple modal shakers outputting a sine wave to acquire FRF signals. The Source Output type is either Swept sine or Stepped sine. The sweep mode can be linear or logarithmic. The FRF signals of each measurement DOFs with respect to defined reference DOF will be constructed. The output drive level can be defined to run the test under no control strategy, or the response of a control channel can be specified to run the test in a closed loop.
-
VDA124RM-12 -
MicroImage Video Systems
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
BL-VDA124-01 -
MicroImage Video Systems
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
VDA212RM -
MicroImage Video Systems
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
VDA106 -
MicroImage Video Systems
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
VDA212RM-12 -
MicroImage Video Systems
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
VDA124RM -
MicroImage Video Systems
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Teledyne LeCroy quantumdata
The Teledyne LeCroy quantumdata 980 48G Protocol Analyzer / Generator module for HDMI 8K Testing is equipped with both an HDMI Tx/Output port for TMDS and Fixed Rate Link (FRL) video generation and an HDMI Rx/Input port for TMDS and Fixed Rate Link (FRL) video and protocol analysis. The HDMI Tx and Rx ports support testing of formats up to 8K formats at 1485MHz pixel rates. Full compliance test suites are supported in FRL and TMDS modes for both HDMI sources and sinks.
-
MaxTester 940/945 -
EXFO Inc.
First tablet-inspired, multifunction optical loss test set (OLTS) delivering insertion loss, optical return loss and fiber length measurements at two wavelengths in five seconds via fully automated bidirectional FasTesT™ analysis. With its step-by-step reference wizard and intelligent fault diagnosis, the MAX-940/945 provides expert guidance throughout the test process to ensure immediate efficiency by first-time users while removing risk of errors or negative loss—a common source of issues when testing low loss fibers.
-
PI-6000 -
ETI Precision
The PI-6000 is a rugged & durable primary injection test set capable of testing circuit breakers up to 6,000 amperes frame size. It incorporates an output transformer with dual primaries to facilitate its use on power sources of 480 VAC as well as 208-240 VAC. The unit also includes dual secondaries to provide optimal impedance matching to a wide range of circuit breaker sizes. An internal voltage sensor automatically configures the AC control power section to be energized only when properly configured for the applied voltage.
-
TRM 104 -
Scope T&M Pvt, Ltd.
TRM104 is a portable winding resistance meter, designed to work in live EHV switchyards. Winding resistance values of large transformers up to 500 MVA and rotating machines are directly displayed. The meter is protected against the back emf offered by large inductive winding. A back-lit 4 line LCD with a user-friendly menu sets up the instrument for the test. Winding resistances and safety messages are also shown on this display. It is possible to measure the resistance of two windings simultaneously.The meter contains a special power source for rapid stabilization of test results.
-
Pocket MicroTechnics
GLCD Font Creator is the ultimate font creation utility for embedded systems. It lets you create fonts for Liquid Crystal Displays (LCD) and Graphic LCD. It provides a very nice and intuitive user interface. GLCD Font Creator lets you create fonts and symbols from scratch, or by importing existing fonts on your system. It lets you modify and adjust them for your needs, apply effects to them, and finally export them as source code for use in your favorite language compiler.
-
quantumdata M21 -
Teledyne LeCroy
The Teledyne LeCroy quantumdata M21 Video Analyzer for HDMI and DisplayPort testing offers a wide array of benefits to design and engineers in R&D as well as professional A/V installers for testing HDMI and DisplayPort source devices. The M21 instrument is also equipped with an HDMI 48Gb/s video generator enabling test engineers and pro A/V integrators to run a variety of video, audio and protocol tests on digital video displays. With both an HDMI video analyzer and a video generator, the M21 can be used to test distribution equipment and cables as well.
