Showing results: 1006 - 1020 of 2874 items found.
-
CAS 140D -
Instrument Systems Optische Messtechnik GmbH
The latest high-end CAS 140D array spectroradiometer from Instrument Systems is seen as a benchmark for high-precision spectral light measurement technology both for weak light sources and high radiation intensity.
-
YAVAP955 -
6TL Engineering
The YAV board AP955 contents 10 CAN Bus programmable bipolar Isolated precision and low noise 0 to 5VDC voltage sources up to 400mA output, with Tripaddle VPC connector.
-
Model: DS-7230 -
De Vries Scientific
The Antenna Bore Site Simulator is comprised of an all weather antenna-source and remote controller. The antenna-source is a synthesized frequency source with 30 dB attenuator, internal modulation capability and dual polarized antenna.
-
LM-101 -
Eddy Co.
The LM-101 Light Monitor system provides an efficient and cost effective solution for monitoring coating thickness in real time. It consists of the LM-101 Light Monitor, LM-101A/AS light source, and Detector assembly.
-
6050 -
PRODIGIT Electronics Co, Ltd.
Single Output USB PD USB PD basic version:the single-group test systemarchitecture is as shown in the table, 5302A AC Source, 3302F + 3310F series and9922-R Quick Charge Controller.
-
BlazeMeter -
Perforce Software Inc.
BlazeMeter was designed and built by engineers who are passionate about open source. From mobile to mainframe, IDE or UI, bring teams together in a single platform with shared visibility, tests, and reports.
-
9501C -
Hydraulic Technology, Inc.
The 9501-9501C hydrostatic test pump provides a safe source of hydraulic pressure for proof testing pressure vessels, hose and tube assemblies or other components that require periodic proof pressure testing.
-
LightTrans GmbH
Fast physical optics provides a cogent model of laser sources, while also considering diffraction, interference, polarization and nonlinear effects, as well as granting access to any beam parameter of concern.
-
Praxsym
The Praxsym CW Transmitter is a complete, portable continuous wave test source. Used as an input source to test a distributed antenna system, the Praxsym CW Transmitter can provide test signals aiding in the design and optimization of in-building and outdoor networks.
-
ET System Electronic GmbH
More and more customers want integrated systems in which the devices are supplemented with additional components and delivered turnkey. ET System electronic offers all services for this system integration from a single source. The sources and electronic loads are fully wired according to customer requirements, installed in 19 "cabinets and equipped with special features. For example, sources and loads can be combined with one another and supplemented with special interfaces or emergency stop functions. The integration of insulation monitors, interlock functions and the installation of industrial PCs is also possible, as is the installation of special safeguards, for example if each channel is to be safeguarded separately in multi-channel devices.The respective configuration can be based on any machine guidelines and standards, and the systems can be integrated into any existing environment with additional connections. On request, space and connection options for additional devices can be provided in the 19 “cabinets so that customers can easily integrate their own components.
-
CM8 -
North Atlantic Industries
The CM8 module is a combination of NAI's MIL-STD-1553B module, FTB, and Enhanced Discrete I/O module, DT4. The CM8 offers twelve channels of discrete I/O and two channels of MIL-STD-1553B communications. The twelve discrete I/O channels are programmable as either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3-60 VCC source. The discrete I/O channels also provide additional functionality modes such as Pulse Width Modulation (PWM) output mode and Pattern Generator output mode. The two MIL-STD-1553B communications channels feature a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Rohde & Schwarz GmbH & Co. KG
Complete your EMC test setup with the essential accessories to compliment the test equipment. Whether it is a LISN (or V-Network) to counteract interference from external power sources on conducted emissions from the device under test, probes to locate the near field sources of radiated emissions, receive and transmit antennas, or tripods for holding antennas in place, the Rohde & Schwarz catalog of EMC accessories provides the additional items you need for EMI and EMS measurements, guaranteed 100% suitable for use with Rohde & Schwarz EMC test equipment.
-
Opto Diode
Opto Diode manufactures five families of infrared emitters that are used for a variety of medical and industrial applications, including gas analysis, environmental monitoring, spectroscopy, and process control. From the steady state (DC) emitters (SA Series), to high-power steady state emitters (SHA Series), to pulsable sources of black-body radiation (SVF Series) and fast pulsable sources of black-body radiation (SPF Series), to high-speed IR emitters with integrated drive electronics (PIREPLUS), we have the perfect family of products for your critical requirements.
-
ThetaCalc -
Thermal Engineering Associates, Inc.
A tool designed to provide a quick estimate of the temperature and thermal resistance from a heat source to a reference heat sink. It also shows the temperature and thermal resistance value of each layer in the heat flow path. The program can accomodate up to ten layers of different materials of varying dimensions between the heat source and sink. The heat spreading angle can be set independently for each layer to a value between 0 and 45 degrees; the tool will automatically determine if heat flow reaches the layer edge and then convert to columnar flow.
-
APCI-3300-8 -
TEAM SOLUTIONS, INC.
18-bit resolution, unipolar, 16-bit accuracy 8 differential inputs for strain gauges Voltage range 0 to + 2.5 V 8 independant voltage sources for the connected pressure sensors Output voltage for the voltage sources 5 V, 40 mA Gain and offset calibration Calculation of the pressure value through software Programmable gain 16-bit accuracy with sample rates of 20, 40, 80 or 160 Hz 4 digital input channels, 24 V and 3 digital output channels, Open Collector, isolated