Showing results: 16 - 30 of 155 items found.
-
Mors Smitt Group
The Mors Smitt transducers are used to measure high currents in rolling stock and trackside applications. High currents are converted linearly to low power signals.
-
907 XP (Explosion Proof) -
Electro-Sensors, Inc.
Features • NPN open collector, square-wave output • Zero speed operation with no signal loss • Non-contact, large gap distance sensing • Signal transmits up to 1,500 ft • Simple to install and set up • Powered by 5-24 VDC • Class I, Div I (D) Class II, Div I (E, F, G) Class III • XLB-3 enclosure • Bi-directional option (907B XP)
-
ChenYang Technologies GmbH & Co. KG
A Hall Effect proximity switch is a non-contact electronic switch, which consist of a permanent magnet or ferromagnetic part as trigger intermediary and a Hall Effect sensor IC. The Hall sensor IC detects the change of the magnet field when the permanent magnet comes in the close proximity to it and generates an electric signal. This signal is amplified and rectified to control the output signal of the switch.
-
SPECTEC Innovative Sensor Solutions
SPECTEC zero speed Hall effect gear tooth sensors are used in industrial applications to determine shaft or gear speed or direction by detecting fluctuations in the magnetic field. The Hall effect technology fulfills a wide array of applications due to a Hall effect sensor's ability to detect zero speed and the quadrature sensor's ability to detect direction change. The Hall effect gear tooth sensor's digital output is easily read by computers, motion control devices, position monitors and digital to analog converters. Intrinsically Safe zero speed sensors are available for various applications.
-
RH 2010 -
PhysTech GmbH
The RH 2010 Hall Effect Measurement System has been designed for high flexibility and ease of use as a standard system for quick routine control measurements as well as for sophisticated temperature dependent Hall measurements for material research.
-
ChenYang Technologies GmbH & Co. KG
is a sophisticated Hall Effect Gear Tooth IC featuring an on-chip 12-bit A/DConverter and logic that acts as a digital sample and hold circuit. A separate 6-bit D/A converterprovides a fixed hysteresis. The sensor does not have a chopper delay. It uses a single Hall platewhich is immune to rotary alignment problems.
-
HMS-3000 -
ECOPIA
Hall Effect Measurement System is very useful for measuring Carrier Concentration, Mobility, Resistivity and Hall Coefficient that should be pre-checked in order to grasp the electrical specifications of semiconductor device. Therefore, it is essentially required system to understand the electrical characteristics of semiconductor device.Ecopia’s HMS series consist of constant current source , terminal conversion system by Van der Pauw technique, low temperature(77K) test system and magnetic flux density input system. So, it is well-established system that has all the things needed to Hall Effect Measurement System.
-
HEM -
TOEI INDUSTRY CO, LTD.
The physical quantity of Hall Coefficient, Hall Mobility and Carrier Density etc. can be investigated by measuring at room temperature voltage occurred perpendicularly to the both magnetic field and constant-current when flowing constant-current perpendicularly to magnetic field from current source while applying magnetic field to sample set at the center of magnetic field of magnet.
-
ChenYang Technologies GmbH & Co. KG
ChenYang Technologies GmbH & Co. KG supplies various kinds of Hall Effect vane sensors (CYHME301, CYHME56, CYHME2000) for speed measurement with applications to machines, equipments, motorcycles (BMW ), automobile industry etc. We are specialised in design, development and production of Hall-effect sensors and can offer also custom Hall sensors for your special applications.
-
McLAREN Applied Technologies
The output of the Rotary Hall-effect sensor is a voltage which changes in direct proportion to the shaft angle. The sensor is non-contact, using Hall elements to determine the angle of a magnet. The magnet is either mounted in a shaft integral to the sensor or can be mounted externally to the sensor.
-
BEI Industrial Encoders
BEI Sensors Hall effect sensors meet customer needs for high performance, non-contact rotary position sensor solutions. This product line features a standard operational life of 35 million cycles while providing up to 6-turns with 2160 degrees of resolution and linearity of +/-0.5%. Capable of having redundant outputs, meeting up to IP69K sealing requirements and operating temperatures of 85 C , these rotary hall effect sensors are ideal for a wide variety of applications. Ideal applications include steering, pedal and throttle for off-highway equipment, dancer controls in web processing, flow control valves and elevator door opener operations.
-
HMS-3300 -
ECOPIA
Magnetic flux density : 0.55Tesla (+/-0.03T)Gap distance between both round magnets : 26mm / Round magnet diameter : 50mmMeasurable temp : RT ~ 300℃(model# HT55T3). Resolution : 0.1℃(Model# HT55T5 : RT ~ 500℃)Both HT55T3 and HT55T5 are only capable of using with HMS-3000 main body.(Not compatible with HMS-5000 )- You can flow purge gas into small chamber and measure hall effect at the same time. Gas control valve can be installed as an option.
-
ECOPIA
Permanent magnet - Neodium materials - +/- 0.03Tesla deviation can be made in a process of assembling magnet. - However, we indicates correct tesla strength measured by gaussmeter, before shipping magnet kit.
-
300 Series -
Integrity Design and Reseach Corp.
Typical Applications include Measurements of the Earth's field vectors, Air shipment inspection, Mapping and recording field perturbations, Magnet classification, Analysis of magnetic circuitry and components, Magnetic Resonance Imaging (MRI) and Measuring residual fields.
-
Magna-Mike 8600 -
Olympus Corp.
The Magna-Mike® 8600 is a portable thickness gage that uses a simple magnetic method to make reliable and repeatable measurements on nonferrous materials. Operation of the Magna-Mike is very simple. Measurements are made when its magnetic probe is held or scanned on one side of the test material and a small target ball (or disk or wire) is placed on the opposite side or dropped inside a container.