Showing results: 1831 - 1845 of 5162 items found.
-
MEG-700A3T -
ELMA Electronic, Inc.
AC/DC power supply from Delta | input 90 - 264 VAC | configurable output | temperatures from -20 to +70 °C
-
PeakTech Prüf- und Messtechnik GmbH
Environmental video measuring device with a dual laser for exact target area determination for fast, accurate and non-contact surface temperature measurements.
-
Canden Products LLC
Insect growth chamber, Insect rearing chambers, Insect incubator, mosquito growth chamber- Temperature and humidity controlled Reach-in chambers
-
Advantech Co. Ltd.
Arm-based industrial gateways are based on NXP, Qualcomm, Rockchip, and TI, delivering LTE, 5G and Wi-Fi with wide operating temperature range.
-
ZhangZhou Weihua Electronic co.,ltd
Is a thermometer which infers temperature from a portion of the thermal radiation sometimes called blackbody radiation emitted by the object being measured.
-
510108115 -
Virginia Panel Corporation
These mini power modules can withstand temperatures up to 140 °C. The faces of the power modules are screened with a red strip to indicate power.
-
MicroTemp -
MadgeTech, Inc
The MicroTemp is a miniature, submersible, self-contained temperature data logger. Only 2.6” (66mm) tall and 0.7” (18mm) in diameter, this data logger can easily fit into the smallest spaces. It can even fit down the neck of most beverage bottles! Don’t let the diminutive size fool you — this is an industrial grade instrument which boasts an accuracy specification of ±0.5ºC and will operate in temperatures from –40 to +80ºC.
-
DeltaTRAK
The DeltaTrak FlashLink Mini Multi-Use Data Logger is ideal for customers looking for a low cost temperature data logger that can be programmed and reused. The FlashLink Mini Multi-Use data logger can be used in production and processing areas, or anywhere that tracking of temperature sensitive commodities or environmental conditions is needed. The data logger's sensor operates within a range of -40°C (-40°F) to 66°C (150°F).
-
IT-18 -
Physitemp Instruments
IT-18 Flexible Implantable Microprobe - Implantable in semi-solids and tissue with 18 gauge needle (supplied). Also for immersion in various solutions and rectal temperatures of small animals. Totally sheathed in chemical resistant Teflon™. Quited rugged. Maximum Temperature 150°C . Isolated. Probe diameter .050" (14 gauge represents the needle gauge that the probe can be inserted through). Time constant 0.3 seconds.
-
IT-21 -
Physitemp Instruments
IT-121 Flexible Implantable Microprobe - Implantable in semi-solids and tissue with 21 gauge needle (supplied). Ideal for subcutaneous and cranial temperatures in small animals. Also for immersion in various solutions. Totally sheathed in chemical resistant Teflon™. Maximum Temperature 150°C . Isolated. Probe diameter .016" (21 gauge represents the needle gauge that the probe can be inserted through). Time constant 0.08 seconds.
-
BT-1 -
Physitemp Instruments
BT-1 General Purpose Probe - Probably our best general purpose probe designed for temperature measurement of solids, liquids, gases and semi-solids. Welded stainless-stell shaft, plastic handle. Tip is .028'' diameter bent at right angle to probe to facilitate accurate surface measurements. Immersible. Maximum temperature 240°C, Time constant 0.15 Seconds. 5 foot lead. Not isolated.
-
ST60 Quad -
Dexter Research Center, Inc.
A four-channel silicon-based thermopile detector in a TO-5 package. Each small active area size is 0.61mm x 0.61mm. This is our lowest-cost and fastest time constant four-channel detector. It delivers a time constant of 18ms with Nitrogen encapsulation gas combined with a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
SKZ145 -
SKZ Industrial Co., Ltd
To determine the melt mass-flow MFR /10min, the melt volume-flow rate MFVcm3/10minand the melt density of thermo resin, for the engineering plastics of polycarbonate, nylon and fluorine plastics, etc, whose melt temperature are higher, but also fit for the plastics tests of polyethylene, polystyrene, polypropylene, ABS resin and poly-formaldehyde resin, etc, whose melt temperature are lower, it is widely applied to the fields of plastics materials, product, petrochemical
-
Advanced Science and Novel Technology, Co., Inc.
DC to 25GHz broadband linear signal splitterOne differential CML-type input port and four phase-matched differential CML-type output portsDifferential input linearity range up to 1000mV p-pDifferential gain of approximately -1.5dBLow jitter and limited temperature variation over industrial temperature rangeSingle +3.3V or -3.3V power supplyPower consumption: 1.35WFabricated in SiGe for high performance, yield, and reliabilityCustom CQFP 44-pin package
-
Laser Components IG, Inc.
Pyroelectric detectors are thermal detectors; i.e. they create an electric signal due to temperature changes in the chip. This temperature change is caused by absorption of light. We do use LiTaO3 and DLaTGS as pyroelectric materials. Basically such detectors cover the whole spectra. However, they are mainly used for mid-wave and long-wave infrared detection (MWIR and LWIR). In addition, the usage in the THz region seems to become more popular these days.