Showing results: 1681 - 1695 of 2550 items found.
-
Kuhne electronic GmbH
Bias Tee for remote power supply of preamplifiers and converters via the coaxial cable.
-
Fairview Microwave Inc.
Fairview’s bi-directional amplifier models are designed for use in both commercial and military applications and will support any signal type and modulation format such as 3G and 4G telecom, WLAN, OFDM, DVB and CW/AM/FM. Fairview’s bi-directional amplifiers offer high power density, efficiency and linearity in small lightweight environmentally sealed packages with SMA connectors. These units also feature a quick-connect circular locking connector for DC and control functions and each design uses a single voltage supply with voltage regulation.
-
KP Series -
MATSUSADA Precision Inc.
KP series is the sophisticated bidirectional power supply device with the regeneration capability*, optimal for evaluating not only in-car inverters for hybrid and electric vehicles but motors, generators, high-capacity vehicle batteries and capacitors as well as wind or solar power generation. We make available the extensive lineup ranging from 2kW to 120kW so you can choose the optimal model according to various applications including development and production.
-
LD-LBOD-A10 -
Labodam
BOD MeterLD-LBOD-A10is a benchtop unit designed to automatically measure B.O.D. (biological oxygen demand) with 0 to 4000 mg/ L measurement range. Simple and safe mercury pressure difference measurement method is applied to prevent poisoning caused by the leakage of the mercury column. Equipped with high end brand mini thermal printer, quickly prints measurement process data, result data. Automatically saves test data on power failure and executes experimental process once power supply is on.
-
Fiberinthebox
Cable Fault Locator is a device used for short circuit faults, cable cuts, resistive faults, intermittent faults, and sheath faults. Fiberinthebox supply cable fault locator for power cable, optical fiberal cable, etc. Fault Location in Power Cable is designed to locate cable faults, pinpointing the fault location, route tracing, cable identification, voltage withstand test and cable information management. It can locate all kinds of cable faults for all voltage level cables, including open circuit, short circuit, low insulation, high insulation and flashover faults, etc. Most power cables were buried underground, invisible, and out of reach, with modern new power cable fault locater, it can find the fault point quickly, solve problems immediately and restore power supply.
-
Meco Instruments Pvt. Ltd.,
Stability DC : < 0.01 %FS / 3 min, AC : < 0.02 %FS / 3 minRipple : < 0.2 %Power Supply : 230 VAC, 50 (60) HzPower Consumption : < 250 VAOperating Temperature : 5ºC to 35ºCRelative Humidity : ≤ 80 %Distortion : < 0.5 %Display : 51/2 Digit LED Digital DisplayStep adjustment of Output Signal : 100 %FS / N, 10 %FS / N,%FS / N, 0.1 %FS / N (N = 4, 5, 6, 10 and 15)Dimensions : 190mm (H) x 480mm (W) x 545mm (D)Total Weight : 22.5 kgs (approx.)
-
72-6694 CAL -
Tenma
The 72-6694 CAL from Tenma is a current calibrator. It provides quality and accuracy of handheld calibrator of precision current source. It features large LCD display (maximum display counts 1999, 13mm (0.5") digit size). The current calibrator has 006P DC 9V, MN1604/PP3 battery or equivalent alkaline type or heavy duty type power supply. The dimension is 185mm × 78mm × 38mm (7.3" × 3" × 1.5") and weight is 265g/0.58lb (including battery). It has adjustable 0 to 24mA current source, 2 ranges (0 to 19.99mA (0.01mA display resolution, ±(0.25% FS + 1d) accuracy), 0 to 24mA (0.1mA display resolution, ±(0.5% FS + 1d) accuracy).
-
72-6694 CAL D -
Tenma
The 72-6694 CAL D from Tenma is a current calibrator. It provides quality and accuracy of handheld calibrator of precision current source. It features large LCD display (maximum display counts 1999, 13mm (0.5") digit size). The current calibrator has 006P DC 9V, MN1604/PP3 battery or equivalent alkaline type or heavy duty type power supply. The dimension is 185mm × 78mm × 38mm (7.3" × 3" × 1.5") and weight is 265g/0.58lb (including battery). It has adjustable 0 to 24mA current source, 2 ranges (0 to 19.99mA (0.01mA display resolution, ±(0.25% FS + 1d) accuracy), 0 to 24mA (0.1mA display resolution, ±(0.5% FS + 1d) accuracy).
-
72-6694 CAL DU -
Tenma
The 72-6694 CAL DU from Tenma is a current calibrator. It provides quality and accuracy of handheld calibrator of precision current source. It features large LCD display (maximum display counts 1999, 13mm (0.5") digit size). The current calibrator has 006P DC 9V, MN1604/PP3 battery or equivalent alkaline type or heavy duty type power supply. The dimension is 185mm × 78mm × 38mm (7.3" × 3" × 1.5") and weight is 265g/0.58lb (including battery). It has adjustable 0 to 24mA current source, 2 ranges (0 to 19.99mA (0.01mA display resolution, ±(0.25% FS + 1d) accuracy), 0 to 24mA (0.1mA display resolution, ±(0.5% FS + 1d) accuracy).
-
Auto -
CanDo
The CANdo AUTO Module is a rugged, multi-purpose CAN bus module with a USB port, two precision analogue inputs & a DC power supply input. The module is capable of operating either connected to a PC, or in a standalone mode powered from a 12 or 24V DC supply, such as a vehicle battery. The module maybe used as an interface between a PC & a CAN bus, or between analogue sensors & a CAN bus, in standalone mode. In addition, the module maybe programmed to transmit fixed, periodic CAN messages automatically on power up.
-
LVPS -
Tech-Aid Products
This is our standard power supply board used in many of our testers but also available separately. This board is capable of +/-15v, +10 and +5v outputs. Also contained on board is our standard meter drive circuitry for testing instrument meters, a two-pole relay and an option for a sine/cosine oscillator circuit.
-
72-6628 -
Tenma
The 72-6628 is a Triple Bench Power Supply with adjustable current control and galvanized steel case. The DC regulated power supply is a completely solid state, compact, well regulated, constant voltage power supply suitable for service field, hobby, laboratory and testing use. It provides three different voltages output for different. Overload and short-circuit protection, prevent the unit from overload and short circuit. When the unit is under the condition of overload or short circuit, the output current will be limited. Independent 5V, 12V easy snap-on output terminals to make it easy to use for TTL and CMOS circuit testing. The grounding of the output terminals is independent that the output can be connected in series to make a higher output voltage.
-
BD15-48P -
Manatronics Pty Ltd
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
BD12-24P-12 -
Manatronics Pty Ltd
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 24V battery systems and is extremely cost effective.
-
JT631 Series -
Nanjing Jartul Electronic Co., Ltd
JT631 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT631 series load very suitable for testing power supply when produced in large quantity. Besides, JT631 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT631 series load satisfing most of R&D requirements. Moreover, JT631 series load’s special parallel operation method can satisfy the synchronous loading requirements of multi-channels output power supply and satisfy single-channel output power supply requirement for big power.
