Showing results: 1861 - 1875 of 2550 items found.
-
TOMSAD
*on / off switch output section*two independent adjustable DC output*independent outputs serial and parallel*constant voltage and current*Low ripple and noise*four digit LED displays three*for 16 hours at full load*automatically search out
-
TOMSAD
Power stabilized POWERLAB series are high precision current sources with variable voltage and current over the entire range . They can operate in different modes of stabilization voltage or current switched automatically with adjustable limit value of the load current at any point in the range.
-
N6700 MPS -
Acery Technologies
N6700 MPS has 16 different DC power supply modules, so test system designers can use these modules according to their specific test requirements to establish 1 to 4 channel DC power supply system. In the requirements of speed and accuracy of the occasion to invest in high-performance output, and for the general requirements of the DC power supply to buy basic performance output.
-
PMT-101 -
Eddy Co.
Photo Multiplier Tube with a range of 185 - 700 nm. Has a built in power supply. Built in low noise amplifier with a gain of x1 and x100.
-
PMT-102 -
Eddy Co.
Photo Multiplier Tube with a range of 185 - 875 nm. Has a built in power supply. Built in low noise amplifier with a gain of x1 and x100.
-
Model 910 -
Ametek Power Instruments
The PANALARM Model 910 is a compact ten-point annunciator that meets DIN 43700 standard dimensions. A complete integral package includes an LED display, power supply, pushbuttons, two relays (output reflash and common audible). Optional integral horn is also available. The Model 910 offers a unique combination of economy and small size using microchip I² logic. It has normally open/normally closed field contact selectability with ten input points on one logic card. Operational sequences are field selectable; choose from seven available sequences.
-
VBT100 -
Silicon Control Inc.
The VBT100 has been designed to withstand and measure excessive voltages on both signal and power supply pins. This capability allows it to operate in faulty backplanes that could damage other boards. The tester also detects, measures and identifies which signals have excessive voltages so they can be repaired before boards are loaded into a backplane.
-
RCD -
Junxy Energy
RCD AC load banks are used to test the REAL working condition of UPS, rectifier, inverter and etc who are loaded by non-linear or electronic load with non-constant resistance such as computer, networking equipments and etc. Through the accurate detection of its output and power quality, users could avoid the inadequate loading capacity or cause pollution to power grid, so as to guarantee supply security. JUNXY RCD load banks leading power factor loads are created to debug power supply system parameters such as its crest factor test.
-
EE105T-xx -
Executive Engineering
The EE105T pre-wired bias power cable is designed to be used with the EE301xx & EE151xx series electronic loads. The cable allows you to connect the electronic load to a regulated 12Vdc bias power supply for operation of the electronic circuits in the load or by moving a wire use the 15-24 Volts unregulated input
-
Dual AES DAC (4Ch OP) -
Murraypro Electronics
The Cat: 390A/S demodulator has been designed to be fitted within analogue audio equipment that lacks a dedicated AES/EBU digital input, providing a transparent interface with the external digital input. Two channels are housed on the compact card only 80 x 50 mm, each furnishing a balanced audio OP. The modest +12Vpower requirements of the card are usually drawn from the host equipment, removing the requirement for a separate external power supply
-
FM-204M50KG -
Guangzhou Landtek Instruments Co. Ltd.
LANDTEK Digital Muscle Dynamometer Muscle Strength Tester FM-204M50KGApplications:Making job task analysis and ergonomic analysis simple and accurate, it is ideal for workplace design, strength assessment and ergonomic research.Details:Force Rang:±50kgf,±490N,±110LbfResolution:0.01kgf,0.1N,0.1LbfAccuracy:±0.5%FS ± 1DigitUnit:kgf, gf, N, LbfMeasurement State:Peak Value Measurement, Real Time MeasurementDisplay:2 Reversed 4 Digit LCDPower Off:10 Minutes Auto Power Off, Manual Power OffBacklight:BacklightSafe Load:150%FS (Buzzer Alarm Over 110%FS)Power Supply:2x1.5 AA(UM-3) Battery or 5VDC Power SupplyOperating:0°C~40°CConditions:< 80%Surrounding:No Vibration Source or Corrosive Medium AroundWeight:705 gSize:host machine:170mm*72mm*35mmhandspike:315mm*Φ30mm Instrument stents:155mm*95mm*35mmAccessories:Standard Accessories:ManualCarrying CaseInstrument stents4 M3*18 screwsE-1005Optional Accessories:External USB power supply cableE-1004For quotation please feel free to contact Lisa Li. Thank you.
-
NanJing DVP OE TECH CO., LTD
*High output power*Stable and reliable*CW or MOD output*MOD frequency: 270Hz/1KHz/2KHz*SMT, lightweight*Power supply by battery
-
Naneos Particle Solutions gmbh
OEM sensors can be used to be built in proprietary systems. If you have e.g. a laboratory setup with your own flow, power supply and data aquisition, you can implement a custom sensor into your system. We provide different sensors for different applications, concentrations and flow ranges.
-
NanJing DVP OE TECH CO., LTD
*High performance detector*Stable and reliable*High sensitivity*Multi-wave test*Relative and absolute power display*SMT, lightweight*Power supply by battery
-
CM8829 -
Rinch Industrial Co.,Limited
- Operating principle: magnetic induction/eddy current (F/NF)- Measuring range:0-1250um/0-50mil- Resolution; 0.1/1- Accuracy: 閸?-3%n or 閸?.5um- Min. measuring area: 6mm- Min. sample thickness: 0.3mm- Battery indicator: low battery indicator- Metric/ imperial: convertible- Power supply: 4x1.5V AAA(UM-4)battery- Auto power off- Operating conditions:0-+45闁?/span>(32闁?/span>-104闁?/span>),闁?0%RH- Dimensions: 126x65x27mm- weight: 81g(not including battery)- Optional accessories: other range 0-200um to 15000um