Showing results: 1291 - 1305 of 1806 items found.
-
PCE Instruments
Here you will find gas analyzers that meet industry standards relating to personal safety and that are mainly used to detect and measure levels of methane, hydrogen sulphide, carbon monoxide, oxygen and 50 other gases. The auto-calibration function allows for easy calibration. Some of them also possess the ability to store values and can later transfer data to a computer. One accessory is the manual aspirator, with this device, you can draw gas directly into the analyzer via a 2 m long tube with which you will be able to measure gas levels without having to be in direct contact to the gas source or to be able to determine the levels of gas in places that are difficult to access.
-
US-454A -
United Western Technologies Corp
The US-454A is a portable, hand-held, battery-operated multi-frequency eddy current instrument that can be connected to a laptop, PC and motion controllers for use in semi- or fully automatic data collection applications. Two encoder inputs enable position stamping of data. Pulse-on position input is ideal for motion control applications. Ethernet and USB capabilities allow instrument control along with time- and position-stamped data transfer to the client computer. Built from the rugged US-454 architecture, the US-454A offers single- and multi-frequency inspection, frequency mixing capabilities, enhanced signal-to-noise ratio, USB, Ethernet and data storage capability, and unprecedented digital strip chart data collection.
-
FastX1703-DIG -
Alacron
The FastX1703-DIG is a raw-length PCI board with two input connectors. Each connector supports 16 data bits, 10 general purpose inputs, and 6 general purpose outputs. Clock rates up to 166 MHz can be supported. All the inputs and outputs are connected to an FPGA on the board are essentially available for any purpose required by the interface. The front-end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, zero to four Nexperia PNX1702 VLIW processors before output. Finally, the Fast-X-DIG interfaces to the host computer through a 4 x PCIe interface for state-of-the-art data acquisition.
-
PCI-A12-16A -
Acces I/O Products, Inc.
Model PCI-A12-16A is a multifunction, analog-to-digital, digital-to-analog, and digital I/O card. It accepts up to 16 single-ended inputs or eight differential inputs. Inputs are protected against over-voltage conditions up to ±35 volts and typically survive static discharges beyond 4000 volts. Conversions can be initiated in any one of three ways: (a) software command, (b) external start commands, or (c) on a timed basis using on-board programmable counters. Converted data may be transferred to the computer by one of two software selected methods: (a) polling for the end-of-conversion signal, or (b) by generating an Interrupt when the end-of-conversion signal occurs.
-
AEM-DRA -
Chuan Sheng Electronics Co., Ltd.
The AEM-DRA series has 2 independent and isolated main circuit inputs , can use for different power system.Up to 24 single phase or 8 three-phase circuits, programmable from push buttons with LCM display panel, or using Adtek program software through RS485 communication port.Hardware standard built in a RS485 Modbus communication port , 2 Digital inputs, 4 Relay outputs, LCM and 2 MB flash for data-logging.Optional second communication port for Ethernet, ProfiBus ,LonWorks ,BACnet and Zigbee solutions.Din rail mounting , compact and easy installation, programming through computer and push buttons easy to use.
-
ViTec Co. Ltd
Our automated scanning system is based on smart 3D cameras SICK Ruler E 600. Information about the wheel profile from the camera via a high-speed Gigabit Ethernet interface is sent to a dedicated computer for processing, detecting and recognizing the alphanumeric sequence applied to a specific section of the wheel. Synchronization with the rotation system is carried out by means of a high-precision encoder, with the conveyor system - via the Profibus DP interface. The complex is designed to scan wheels of various standard sizes and allows with a high resolution (tenths of a millimeter), without readjustment, to read numbers from wheels at a radius of 100 to 600 mm in 45 seconds.
-
LW3310 -
Dongguan Longwei Electronic Technology Co., Ltd.
LW3310 wire tester is designed for all kinds of electronic wire, electric wire and connector design, due to the various types of wire and connectors used in every field, this applies only to the commonly used wire detection instrument. Widely used in computer, communication, medical, electrical appliances, motor, automobile and other wiring test.
-
SP-3303 -
Shanghai Powoo Industry Develop Group Limited
Three-phase portable energy meter testing equipment is a kind of dektop portable energy meter which is equipped with three-phase high-stability program-controlled power source and three-phase multi-function standard meter developed and manufactured by the Company; the device can be operated with keyboard to achieve simple functional tests, control and management may be realized through personal computer.
-
IDR-109/IDR-119 -
Integrity Design and Reseach Corp.
Typical Applications include checking the 50 and 60 Hz electric and magnetic fields (EMF) produced by equipments such as transmission lines, computers, electric blankets, electric appliances, televisions, etc.. Magnetic fields are invisible radiations, the best method to detect them is by using one of the accurate gauss meter from Integrity Design & Research corp.
-
43058 -
LINDY-Elektronik GmbH
This tester allows you to quickly and easily test a computer's ATX power supply. It features an LCD screen which clearly and accurately shows the voltage of the connected inputs. Its very compact size (about the same as an iPod Video) and sturdy aluminium case makes it perfect for use by both computer maintenance engineers and system builders.
-
6360-HR-CD -
MicroSense, LLC
The Model 6360-HR-CD Stamper Thickness Measurement System is a semi-automated thickness gauging platform and data analysis system for the measurement of optical media stampers. Patented non-contact capacitive sensors determine the stamper thickness without any damage to the stamper. A personal computer is provided to run the gauging platform, acquire measurement data and display results.
-
GPIB -
Test Electronics
Test Electronics will customize the TE3000 GPIB signal routing box for your test application. Then, you simply rack and stack all the equipment, cable all the switched signals to the back of this GPIB box, add a rack mount computer, plug in the National Instruments GPIB board and software. Then run your customized GPIB based test system.
-
FISHER TESTERS AUTOMATIC TEST EQUIPMENT
• Touch Screen Interface• Windows® 10 Pro• Lowest Board Count in the Industry• High Reliability with Proven Design• USB Interface – No I/O boards in Computer• Remote Control Software for Factory Diagnostics/Updates• Full Network Compatibility• Integral Statistical Reporting• Test Data May be Stored in Multiple Formats• Two Year Warranty on Electronics
-
DRK218 -
Shandong Drick Instruments Co., Ltd.
DRK218 breakdown voltage tester is controlled by the computer, through a new smart digital integrated circuits developed by my company and software control system to make the step-up rate is truly uniform, accurate, and be able to accurately measure the leakage current data. Real-time rendering test curve accurate judgment and it can save, analyze and print test data.
-
CPCI-6713-4 IP -
ALPHI Technology Corporation
The board consists of private SDRAM and Flash memory attached to the 300 MHz TMS320C6713B DSP. An FPGA provides the timing and control. Peripherals include a serial port and connectors for IP mezzanine boards. Flash memory is availablefor downloading programs into a non-volatile memory. A PCIbus connector provides the interface to the host computer. A serial port is available for debugging.
