Showing results: 106 - 120 of 298 items found.
-
3560 -
Abaco Systems Inc
ECM P/N 3560 provides four independent I2C channels. For ease of development a PCA9564 interface IC converts parallel data to I2C serial communication. Additionally an LTC1694 I2C accelerator IC decreases the rise time of the passively pulled up I2C bus allowing for greater capacitive loading or higher bus speeds. Each channel is comprised of SCL, SDA and two Grounds.
-
5093 -
Abaco Systems Inc
ECM P/N 5093 provides 2 independent full bridge circuits. The two full bridge circuits can be used together to drive one small two phase stepper motor. Each full bridge circuit can drive one small dc motor or other bipolar load. Note all inductive loads should employ transient protection.
-
5085 -
Abaco Systems Inc
ECM P/N 5085 provides two channels of 24 bit A/D conversion suitable for high resolution low speed applications, which include bridge circuits, thermocouples, RTD and voltage measurements. For bridge applications each channel provides a fused +5 Volt or a current source drive.
-
5081 -
Abaco Systems Inc
The 5081 provides four channels of 12 bit digital to analog voltage output, with multiple single ended output ranges. Each channel is software selectable for 0 to +5V, 0 to +10V, +/-2.5V, +/-5V, +/-10V or -2.5 to 7.5V ranges. The outputs reset to 0.0 volts on power up.
-
5089 -
Abaco Systems Inc
The 5089 provides eight channels of 12 bit A/D conversion using the Analog Devices AD7328, and is suitable for medium resolution medium speed applications.
-
5041 -
Abaco Systems Inc
ECM P/N 5041 provides eight channels of RS485 / RS422 I/O with fixed 120 ohm termination for each channel. Speeds are up to 30M bits per second. All channels power up as inputs. Also transceiver inputs are always enabled for loop back diagnostic use when the outputs are enabled. Software can enable outputs on a channel by channel basis.
-
MMS6245 -
Abaco Systems Inc
The MMS6245 gives you the ultimate flexibility in rugged embedded I/O by allowing you to customize the 64 user-configurable front panel signals with our patented Electrical Conversion Module (ECM) technology. This configurable XMC carrier can host up to four ECMs giving you the ability to customize I/O to your specific needs.
-
5158 -
Abaco Systems Inc
The 5158 Electrical Conversion Module (ECM) provides eight (8) RS-232 outputs and eight (8) RS-232 inputs. Built around Maxim 1488 & 1489 chips for true RS232 levels and voltage tolerance, all outputs come up in the 1, mark or idle state. Electrically this is a negative output voltage, the start bit is always a 0 or a positive voltage level.
-
MMS8010 / MMS8011 -
Abaco Systems Inc
The Abaco ECM 3U VPX carrier supports up to six Abaco Systems Electrical Conversion Modules (ECMs) in a VITA 46 VPX form factor. Each ECM site connects 32 single-ended 3.3 V signals to the FPGA. The specific ECM board installed on a site converts the FPGA signals to 16 I/O signals, for a total of 96 I/O signals across the six ECM sites.
-
5658 -
Abaco Systems Inc
ECM P/N 5658 provides eight channels of 16 bit current measurement in the 0 to 25 milli-amp range. Each channel allows independent common mode voltages from -100 volts to +100 volts. Current detection is accomplished with a precision 100 ohm current sense resistor, creating a voltage drop of 2V in the current loop at 20 milli-amps.
-
3564 -
Abaco Systems Inc
The 3564 is a four channel comparator board with a common mode range of -150V to 150V on the two differential inputs and a DAC per channel to set trigger levels. The high common mode range and DC coupling provides a robust solution to level detection and triggering.
-
CRS-D4I-3VB1 -
Abaco Systems Inc
4-slot, SWaP-reduced, rugged VPX Intel base plate cooled data processing system that can be applied across various applications including civilian and military unmanned vehicles, manned commercial and military aircraft, helicopters, over- and underwater research vessels, ground vehicles, and locomotives.
-
5235 -
Abaco Systems Inc
The 5235 ECM provides 16 bits of simple digital I/O. The digital I/O is connected directly to the digital I/O on the carrier card. Inputs are clamped to about 3V by FET buffer ICs, and are 5V tolerant.
-
5181 MMS ECM -
Abaco Systems Inc
ECM P/N 5181 uses TI TLV320AIC23 high resolution audio codecs to provide two channels of Audio input and two channels of Audio output. Each input channel consists of two inputs a left and a right, and each output channel consists of two outputs left and right. The outputs are muteable.
-
5676 -
Abaco Systems Inc
The Abaco SystemsP/N 5676 ECM module provides eight channels of 16 bit voltage measurement in the 0 to 2.5V volt range. For each channel the common mode voltage range is -100 volts to +100 volts.