Showing results: 2356 - 2370 of 3343 items found.
-
RTS SERIES -
Transducer Techniques, Inc
The RTS Series torque sensors were designed to fill the need for accurate torque measurements below 62.5 in.lbs. without giving up stiffness or sensitivity to forces from other directions. They are manufactured from sensor quality aluminum and anodized for long term durability. Bonded foil strain gages and materials of the highest quality are installed assuring high reliability. The four bolt hole pattern with the use of our O.D. or I.D. pilots on either end allows simple adaptation to any application.
-
Analog Devices Inc.
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
Arasan Chip Systems, Inc.
A typical mobile device has many low-speed/bandwidth peripherals connected to the host processor, which include microphones, speakers, sensors and many others. There is a need for a standard bus that enables multiple audio channels, peer-peer communications and lower pin count on the host processor. The MIPI alliance has defined the SLIMbus specification which provides a standard, robust, scalable, low-power, high-speed, cost-effective, two wire multipurpose interface that supports a wide range of digital audio and control solutions for mobile terminals.
-
PM7000 -
Outram Research Ltd (ORL)
It offers virtually everything needed to monitor and record power for surveys and audits. It includes 4 voltage input channels capable for measuring 0 to 600 Vac and 4 current input channels for use with voltage output current clamps, or Rogowski Coil sensors supplied. Twelve pre-stored connection configurations are set for 3 phase, 2 phase and single phase measurements. Users can also configure their own set-up and math calculation requirements and save them to non-volatile memory.
-
Orbit Controls AG
Orbit Controls process controllers are designed for direct connection to virtually all industrial sensors and signal sources. They can be used as process monitors to display the process variables to be measured or as process controllers to monitor processes. In addition to the digital display, the devices also have data interfaces, analog outputs and set point outputs. Simple process monitors are optimized in the factory for the desired measuring range and function at the customer's request. The programmable controllers can be parameterized on site via the keyboard or the data interface.
-
Split Collar Pulser Wraps -
Electro-Sensors, Inc.
Pulser wraps clamp around a rotating shaft and work with Electro-Sensors shaft speed sensors and are an ideal solution for installations where the end of the shaft is inaccessible. The two halves fasten together around the monitored shaft with recessed Allen head socket screws (provided). Standard and custom models accommodate any shaft diameter, tight spaces, and keyways. • Standard wraps operate to 3,000 rpm (high-speed also available) • Standard wraps available in PVC, aluminum, or stainless steel
-
SGP30 (Qwiic) -
SparkFun Electronics
The SparkFun SGP30 Air Quality Sensor provides information on the quality of the air in your room or house by monitoring the volatile organic compounds around the sensor. The SGP30 Air Quality Sensor can return valid indoor air quality (IAQ) readings within 15 seconds of powering up! By comparison, typical air quality (IAQ) sensors are great for measuring CO2 and volatile organic compounds (VOCs) but some of them require a burn-in time of 48 hours and a 20-min start up time.
-
McLAREN Applied Technologies
DHE (Differential Hall Effect) sensors give an output when subjected to a changing magnetic field. The field is set up by a magnet inside the sensor body and changes when ferromagnetic teeth are passed beneath the sensor (no magnets are required in the target). To improve noise resistance, the sensor has two Hall effect elements and only responds to changes in magnetic field strength corresponding to tooth passing frequencies above 15Hz. As each tooth passes the sensor, the digital state of the output changes
-
Fluke Calibration
Ensuring process temperature accuracy involves calibrating not only the system’s electronic temperature signals, but also the very temperature sensors that initiate those signals. Rugged Fluke handheld temperature calibrators source and measure RTDs and thermocouples, power transmitters, and store data. Fluke Calibration temperature sources cover temperatures from -45 °C to 1200 °C and include handheld, portable, and benchtop calibrators. Infrared thermometer calibrators and reference measurement thermometers ensure every necessary tool is available to you.
-
GAO Tek Inc.
GAOTek offers a large collection of temperature data loggers that can adjust to any temperature measurement. There are different types of data loggers available in the market including food data loggers, environmental data loggers, and other specific work data loggers. Data loggers measure environmental temperature with the help of built-in sensors that can work in both hot and cold environment like the refrigerator, freezer, and ship containers. These devices are useful in work environments where temperature plays an important role like greenhouse industries.
-
ES620 -
ETAS GmbH
This module measures temperatures using 16 electrically insulated measuring channels for temperature sensors. The adjustable acquisition rate per module is 10 samples/s to 0.1 samples/s. Signal smoothing occurs through a parameterized software filter, and high measuring accuracy is possible through 21 Bit resolution. The automotive measuring range is -210 C to 1372 C (-346 F to 2502 F); J, K, and N type thermocouples are used. Data transfer to PC occurs via Ethernet.
-
Mittal Enterprises
These days ultrasonic instrument has become an evident part of every laboratory. There not only used for medical imaging, detection, measurement and cleaning. But today it is also used for changing the chemical properties of substances. Some of other usage of ultrasonic equipments are fingerprint recognition which is highly and thus every laboratory use ultrasonic sensors for this purpose. After that comes Acoustical analysis for which ultrasonic equipments are best and ultrasonic cleaning which is possible only if you have ultrasonic equipments.
-
JFE Advantech Co., Ltd.
The YODA profiler (“Yoing” Ocean Data Acquisition Profiler) is a “tow-yo” instrument to profile the water column with high spatial resolution from small boats without occupying much space. The instrument is provided with a deployment winch and sensors measuring conductivity, temperature, pressure, chlorophyll, turbidity and dissolved oxygen. The brush at the top of the instrument allows for a stabilizing effect on the free-fall sinking speed, which is approximately constant at 0.2 m/s. All data are stored internally and downloaded into a PC through a wet-connector and interface.
-
HR Series -
Emergent Vision Technologies
Our cameras are available with resolutions of 2, 4, 12, and 20 megapixels in monochrome, color, or near-infrared enhanced (NIR) with full frame rates of up to 338fps, 179fps, 84fps, and 32fps respectively (we can also provide taped on glass). As the first 10GigE industrial digital camera series in the world, our HR and HT cameras (coming soon) obtain their high performance from industrial CMOS sensors with Global Shutter technology in combination with the cross-industry standard 10 Gigabit Ethernet (10GigE) interface.
-
ND-6124 -
ADLINK Technology Inc.
The NuDAM modules provide direct communications with a wide variety of sensors; perform signal conditioning, scaling, linearization and conversion; can acquire measurements of temperature, pressure, flow, voltage, current; and handle multiple digital signal types broadly used in IoT and other industrial applications, such as facility monitoring, environment monitoring, and industrial process control. The new ND-6117, ND-6124, ND-6150, and ND-6160 modules feature Modbus/RTU as the best remote data transmission protocol, which provides customers a comprehensive product offering.
