Showing results: 2851 - 2865 of 3343 items found.
-
XYL-VI -
Lisun Electronics Inc.
The XYL-VI Luminance Photoelectric Colorimeter changes the traditional structure thoroughly, employs the digital X(λ), Y(λ), Z(λ) sensors to replace the traditional analogue sensors, employs the digital signal measurement system to replace the traditional analogue measurement system. The instrument has no analogue unit, thus it is very simple to overcome the zero drift that is impossible to be avoided in traditional colorimeter. The digital sensor has a large dynamic range. Moreover, it possesses strong anti-interference ability and it has high accuracy. The XYL-VI Luminance Colorimeter contains internal RS232 computer interface. The calibration is done by software. It is suitable for monitoring and remote applications. The XYL-VI Luminance Colorimeter can be calibrated by XYL-VI Luminance Colorimeter software to sample the data and print out the results. It can also be corrected by other standard light sources to obtain very high measuring accuracy of x, y color coordinates and color temperature. It is a real-time measuring system and run under Windows2000/XP.
-
Acces I/O Products, Inc.
Sometimes your sensors or the piece of equipment you are trying to control is not in a convenient place to have a PC close by. The sensors may be widely distributed through out your plant and it just wouldn’t be cost effective to run all your wiring to where the PC is. In addition, low level signals are more accurately acquired when digitized close to the signal source. In all these cases our REMOTE ACCES line of products will help. The REMOTE ACCES pods are intelligent, sensor to computer interfaces. Each pod can be used as an autonomous data logger to acquire data for later download. Or as many as 31 pods may be connected on a single two wire multidrop RS-485 network allowing a cable distance of up to 4000 ft. You can also go wireless and extend your range by adding RS-485 wireless transceivers to your serial port. Each unit comes in a rugged NEMA 4 enclosure and can withstand harsh industrial and marine environments.
-
TF Series -
Chuan Sheng Electronics Co., Ltd.
TF series, infrared temperature converters provide non-cotact measurement to caculate the surface temperature of the objects by measuring the energy of infrared light. So It is convenient to measure the surface temperature of especially moving objects. Its stainless case with integrated design combining sensors, optical system, and electronic circuits. It is easy to install by connecting the screw with other devices, and TF can be used in a wide range of industries.
-
AMETEK Sensors, Test & Calibration
We offer a signal multi-scanner which provides a time-saving, automatic solution to calibrate multiple temperature or pressure sensors simultaneously. The scanner may be combined with our dry-block or liquid calibrators, DTI reference thermometers, pressure calibrators, and ASC multifunction process calibrators. Use any place where temperature and/or pressure measurement is critical and there is a need to create traceable documents for sensor calibration.
-
Process & Analytical Instruments division of AMETEK
Measurement Communications & Testing provides the design, integration and installation of critical communication systems, workflow, life-safety solutions and calibration instruments for temperature, pressure and process control. It also is a leader in level measurement devices, continuous position sensors, hardness testers, force measurement devices and retractable cord reels. In addition, it offers a line of weathering test instrumentation along with laboratory and outdoor testing services.
-
MSR147WD -
MSR Electronics GmbH
Data Logger for measuring the physiological properties for textilesThe MSR 147WD, which is equipped with Bluetooth Low Energy (BLE) and a memory that is capable of storing 1 million measured values, enables you to reliably record and wirelessly monitor physiological parameters such as skin temperature and moisture level over long periods of time. The mini data logger has 5 connections for plug-in humidity and temperature sensors.
-
ScopeTester 5 -
DeltaTech Electronics
ScopeTester 5 is 5-channel oscilloscope tester for PCs. Unlike traditional oscilloscopes it is capable of continuous acquisition of signals without dead times. This feature gives exceptional diagnostic value. Available voltage ranges matches typical signals found in modern cars. The user may connect to vehicle sensors, actuators and other diagnostic equipment, such as current clamps, inductive and capacitive probes and other diagnostic probes.
-
ES005 & ES006 -
Teledyne Defence & Space
Teledyne Defence & Space’s (TDS) range of Fast Tuned Notch Filters (FTNF) have been designed to protect Electronic Support Measures (ESM) receivers from high duty cycle, frequency agile interference produced by on board (or cohort) combat radar systems. ESM sensors often need protection from high power nearby radars, and such signals can reduce receiver dynamic range.
-
Lt1245R -
Teledyne Lumenera
The Lumenera Lt1245R uses the Sony Pregius® IMX253 sensor which is the largest of Sony’s global shutter CMOS sensors. With FPGA performance, onboard frame buffering, and Lumenera’s advanced image processing technology, the Lt1245R delivers high resolution images from a camera with a small form factor. This makes the Lt1245R ideally suited for machine vision, life sciences, UAV, and ATI applications.
-
Anton Paar GmbH
Benefit from over 40 years of experience in inline and laboratory beverage analysis: Connect Anton Paar’s versatile and well-proven evaluation units to all generations of Anton Paar density, sound velocity, concentration and CO2 sensors. Let the data acquisition and visualization software master complex measuring tasks for you – bringing home the precision that marks measurement solutions from Anton Paar.
-
MKS Instruments
MKS offers a range of controllers that control ion gauges, heat-loss sensors, and thermocouples. Product features can be configured to meet your specific process needs. A variety of communication protocols, including RS-232, RS-485, and DeviceNet™, are available to speed and ease integration into your control scheme. In addition, many of the controllers provide local displays and a choice of set points that further simplify control system integration.
-
STK -
Analytical Graphics, Inc.
STK is a free 2D and 3D modeling environment used by engineers, mission analysts, operators and decision-makers from more than 700 global organizations to model complex systems (such as aircraft, satellites, ground vehicles and their sensors) to evaluate their performance in real or simulated time. Built on a time-dynamic, physics-based geometry engine, AGI software answers fundamental questions essential to solving dynamic analysis problems
-
TMM-100 -
Thermal Engineering Associates, Inc.
The self contained TMM-100 module accepts diode, thermocouple and thermistor temperature sensors. The USB-connected instrument is supplied with Windows™ 7, 8 & 10 compatible software that provides for sensor measurement on a cyclic basis and for data logging of all measured values. LabVIEW™ Virtual Instrument (VI) drivers are available as an extra cost option for users that wish to incorporate the TMM-100 into an application-specific measurement environment.
-
40-592A-113 -
Pickering Interfaces Ltd.
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
40-592A-104 -
Pickering Interfaces Ltd.
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
