Showing results: 841 - 855 of 1306 items found.
-
81491A -
Keysight Technologies
Keysight's 81491A Reference Transmitter is designed to offer excellent eye quality for NRZ and PAM4 signals at baud-rates up to 32Gbaud and can serve as universal E/O converter. It comes in Multimode (MM) and Single-Mode (SM) flavors and includes internal lasers at 850nm (MM) or 1310&1550nm (SM). External optical input for usage with tunable laser sources is available for SM option. It is fully integrated into Keysight’s Optical Receiver Stress Test solutions to address test requirements of IEEE 802.3 10,40,100 and 400GBASE optical standards.
-
X-eye 9000 Series -
SEC Co., Ltd.
X-ray Tube100 kV / 200 µAMin. Resolution5 µmInspection Ability120ppm , 150ppm, 180ppmSystemConveyor / Index / Pick&Place 방식 LoadingDimension1,800(W) x 1,560(D) x 2,070(H)mm / 5,000kg
-
Technology Products
Sphere Gaps are absolute standards for measurement & calibration purposes of high voltage equipment Sphere Gaps from 20mm to 1500 mm are available. The Sphere Gaps are provided with automated controls with digital display.
-
PCI-DIO-120 -
Acces I/O Products, Inc.
The PCI-DIO-120, PCI-DIO-96 and PCI-DIO-72 are parallel digital input/output cards designed for use in PCI-Bus computers. The same printed circuit board is used for all three models and is populated for 120 bits, 96 bits and 72 bits respectively. The card is 12.2 inches (310 mm) long and may be installed in any 5-volt PCI slot in IBM and compatible computers.
-
KU-2600 -
Kaise Corporation
4000 count LCD 2 times / secAuto / Manual Ranging1.5V R6P or AA Batteries (x2)CATⅡ600V, CATⅢ 300V compliant155(H) x 75(W) x 29(D) mm,Approx. 180gHolster, 100-50 Test Leads, 1.5V R6P Batteries (x2 & spare),Spare Fuses F14 (0.5A/250V) (x1), Spare Fuses F17 (10A/250V) (x1),
-
AX93A01 -
Axiomtek Co., Ltd.
*Specification: 1 x RS-232/422/485, 1 x RS-232, 4 x USB 3.0, 1 x HDMI, 1 x Gigabit LAN, 1 x Audio (MIC-in/Line-out), 1 x Power-on, 1 x Reset, 2 x LED*Dimensions: 118 x 40 mm*Compliant products: PICO312, PICO313, PICO511, PICO512
-
PCI-DIO-24D/H -
Acces I/O Products, Inc.
These cards are 24-bit parallel, digital input/output cards designed for use in PCI-Bus computers. The difference between the models is that I/O connections to PCI-DIO24D are via a standard 37-pin D-sub connector while I/O connections to PCI-DIO24H are via a 50-pin connector. The cards are 4.80 inches long (122 mm) and may be installed in any 5V PCI-bus slot in IBM and compatible personal computers.
-
Model IPC -
Laurel Electronics, Inc
Model IPC Splashproof Cover adds protection to IP67 / NEMA-4X from the front panel. It fits all of Laurel's 1/8 DIN instruments as well as 1/8 DIN instruments by other manufacturers, provided that instrument dimensions in front of the panel do not exceed 48 x 96 x 15 mm (1.89" x 3.78" x 0.59").
-
9956 -
Technobox, Inc.
The Technobox XMC-to-PCI Express adapter with Rear I/O support permits use of a standard VITA 42.3 air-cooled XMC or VITA 20 conduction-cooled XMC in the smallest possible edge finger PCI Express form factor. The length of the adapter is the length of the XMC and 10 mm mezzanine stacking height is supported. The height is a standard PCI Express board and is not the low-profile version.
-
PS200-1U -
Axiomtek Co., Ltd.
*Input Range: 90 ~ 264VAC Full Range*Output Voltage:**+5V, 17A**+3.3V, 14A**+12V1, 6A**+12V2, 12A**-12V, 0.8A**+5Vsb, 2A*MTBF(hours): At 25°C, 100,000h*Safety: CB, TUV, CE, FCC, C-TICK, CUL, UL, CCC*Dimensions: 150 x 81.5 x 40.5 mm*Compatible with Axiomtek products: AX61120/AX60530
-
CM100 -
General Technologies Corp.
Small jaw: 1.2"(W) x 0.53" (D) (300x13.4mm). Clamp opens up to 1/2 inch (12.5 mm). One rotary switch operation. Large 4 digit LCD display. AC/DC Voltage measurement up to 600 Volt. AC/DC current measurement from 0.001 up to 100 A. Relative measurement. One touch auto zero
-
CX-GZ -
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60335-2-9 clause 3 figure 103 Vessel for testing hotplatesParameter:1.Pot and lid material industrial aluminum2. Pot material thickness 2 mm;3. The bottom of the pot body can not be outward convex, can not exceed 0.05mm;4. Pot body and lid surface should be smooth;5, size: 110, 145, 180, 220, 300mm each one
-
Duma Optronics LTD
For analyzing laser beam collimation its direction in space and its profile distribution proprietary instruments were developed. A collimated laser beam with a relatively large beam can be tested with the laser analyzing Autcollimator having an input apreture 100 mm, this device acompanied by AngleMeter U3 and the AngleMeter LA will provide a full product line for analyzing collimated or near collimation laser beams.
-
FilmTek 6000 PAR-SE -
Scientific Computing International
Production-proven metrology system for film thickness, refractive index and stress measurement for a broad range of film layers at the 1x nm design node and beyond. Accommodates 200 or 300 mm wafer metrology. Combines spectroscopic ellipsometry and DUV multi-angle polarized reflectometry with a wide spectral range to meet the challenging demands associated with multi-patterning and other leading-edge device fabrication techniques.
-
CIP-1000 -
Advanced Thermal Solutions, Inc.
The CIP-1000, Controllable Isothermal Plate, is a system for providing an isothermal surface that can be precisely temperature-controlled from 10 to 170C with an accuracy of +/- 0.1C. The CIP-1000 features a 75 mm diameter isothermal copper plate whose constant temperature can be raised or lowered both automatically and manually. A three wire RTD sensor and integral PID controller ensure specific, uniform temperature across the entire plate.