Filter Results By:
Products
Applications
Manufacturers
AC Clamp Meters
measures AC voltage and current without contacting condutors.
-
product
AC/ DC mA Current Clamp-on Transducer
CA-60
This miniature clamp meter features two Hall effect sensors. For use with any multimeter with 200mV or/and 2V ranges for direct readout input impedance of least 1M ohm. High conversion factor for low DC and AC mA measurement. With the small jaw size it can fit into tight space in circuit panel or wire bundle to take the reading.
-
product
Electrical Troubleshooting Kit
Extech MG302-ETK
Extech Instruments Corporation
Test and measurement kit for electrical installation, troubleshooting, and repair.Kit includes:MG302 - True RMS Multimeter/Insulation Tester with 13 Functions and Wireless PC Interface.42509 - 12:1 Infrared Thermometer with high/low alarm and fast 2-color display.MA430T - 400A True RMS AC Clamp Meter with built-in non-contact voltage detector.Complete with with test leads, Type K thermocouple bead wire probe, batteries, and hard storage case that provides protection and organization for the meters and accessories
-
product
200A Digital Clamp Meter
7128A
Peaceful Thriving Enterprise Co Ltd
This is a auto-ranging, high accuracy and stable hand held clamp meter to make electrical maintenance safe and easy. With special designed IC to support true RMS, the meter is available to measure AC/DC voltage to 600V, AC current to 200A and resistance to 20MΩ; also having the capability to test diode, continuity and non contact voltage sensing. Sub switch included Function Select, Max-Min Indication, Value Hold, Range Select, Relative Value Measurement, Illumination and Back-light.
-
product
600A Digital Clamp Meter
7128B
Peaceful Thriving Enterprise Co Ltd
This is a auto-ranging, high accuracy and stable hand held clamp meter to make electrical maintenance safe and easy. With special designed IC to support true RMS, the meter is available to measure AC/DC voltage to 600V, AC current to 600A and resistance to 60MΩ; also having the capability to test diode, continuity and non contact voltage sensing. Sub switch included Function Select, Max-Min Indication, Value Hold, Range Select, Relative Value Measurement, Inrush Current Indication, Illumination and Back-light.
-
product
AC Line Splitter
1937
Peaceful Thriving Enterprise Co Ltd
The AC line splitter is a helpful testing device for electrician. Electrician can measure the current with clamp meter through the X1 and X10 measuring rings. X1 is 1:1 measurement, and X10 is ten times (1:10) of the actual current, which is helpful for small current measurement. This device also combines the function of socket tester and GFCI tester, which means electrician can use this tester to test socket and load at the same time.
-
product
1000A AC/DC True RMS Clamp/DMM + IR Thermometer
Extech EX840
Extech Instruments Corporation
This CAT IV True RMS clamp meter features a built-in IR thermometer with laser pointer for non-contact surface measurements from -58 to 518 °F (-50 to 270 °C). Clamp measures AC current up to 1000 Amp with a maximum resolution of 0.1 Amp. The 1.7-inch jaw fits around conductors up to 750MCM. Peak hold captures motor inrush currents and other surges. Data hold and auto power off functions. Other functions include AC/DC Voltage, resistance, Type K thermometer, capacitance and frequency. Complete with test leads, Type K temperature probe, 9 Volt battery and case.
-
product
Energized Cable Sensor
The purpose of the Energized Cable Sensor is to allow the lineman to readily determine whether a URD cable is energized. The sensor consists of an amplifier which is designed to give a meter reading when the small AC voltage between the semi-conductive sheath and the concentric neutral of the energized URD cable is applied to the test probe. The amplifier is housed in a rugged phenolic case. Sensor may be used to check for energized condition on concentric-neutral cable below an elbow without test points. At cable mid-span (left), hose clamps bridge all strands of concentric neutral at the test location. Sensor’s neutral lead clips to one of the hose clamps. Tip on probe lead contacts only semi-conductive cable sheath to test for voltage presence.
-
product
PC Controlled Bench Top Power Analyzer
PA2100
The PA2100 is a PC controlled bench top power analyzer, allowing several electrical power measurements to be taken simultaneously during testing - from just one set of input connections. The PA2100's power measurement ability is a must in research and development, manufacturing and required for certification and traceability of manufactured goods. In addition to power measurements, apparent power (VA), harmonics, voltage, current, power factor can all be viewed and stored with ease. The PA2100 wattmeter simply connects between the ac supply and the load, various current transformer options allow measurement with any size of current from 10mA to 10000A. Typical watt meter applications include appliance testing; microwave ovens, electric stoves, heating, air conditioning, TVs, monitors, computers, electronic lighting, fans and motor controllers. Powertek wattmeters are equipped with 4mm/banana safety terminals along with optional "breakout" boxes and clamp current probes for fast and safe measurement.
