Showing results: 1381 - 1395 of 2443 items found.
-
PD-20S -
Standard Electric Works Co., Ltd
● Measures both AC and DC voltages with oscilloscopes.● Are typically used to measure high voltages in TV sets, power supplies and instruments in laboratories.● Lightweight and rugged.● 2 available contact tips: round needle tip for normal use and a special flat spring-type for CRT anode.
-
TEL5 -
Standard Electric Works Co., Ltd
● Fast, easy wiring check.● Easy to read light indication.● Confirm the correct wiring of AC socket.● Test GFCI for correct wiring & operation.● Detect 5 wiring faults.● GFCI circuit trips to confirm the tester is working.● The testing current for GFCI is about 8mA.
-
Bestone Industrial Ltd.
It can measure trip-out current, trip-out time, on-line voltage, loop resistance and frequency etc. It’s ideal tool for electrical inspection and repair.Comply with IEC/EN 61010-1 1000V CAT III, 600V CAT IV safety standards.Max common mode voltage: 600V AC RMS.
-
AC3 -
North Atlantic Industries
The module is used to provide an AC signal source when a secondary reference source other than the optional on-board reference module is required. The modules are programmable for full range voltage outputs from 2 to 115 VAC, and frequency from 47 Hz to 10 kHz.
-
AC2 -
North Atlantic Industries
The module is used to provide an AC signal source when a secondary reference source other than the optional on-board reference module is required. The modules are programmable for full range voltage outputs from 2 to 115 VAC, and frequency from 47 Hz to 10 kHz.
-
LI-1500 -
Li-Cor Environmental, Inc.
The LI-1500 connects up to three light sensors with BNC terminals. Package includes four AA batteries, USB cable, AC power supply adapter, carabiner clip, carrying case, Windows® file viewer software, and instruction manual. Sensors sold separately.
-
PeakTech Prüf- und Messtechnik GmbH
User-friendly tester for non-contact voltage testing from 50 V to 1000 V AC. Suitable for outlets, lamp sockets or against wire insulation testing. If AC voltage is present at the relevant measuring point, this is indicated visually by a flashing red LED and the integrated buzzer sounds. If the measuring point is voltage-free, the test probe lights up permanently green.
-
6280 TB -
Standard Electric Works Co., Ltd
● Wide range of operating voltage from AC 210V/50Hz to 250V/50Hz.● For checking AC voltage.● For checking a RCD tester's test current & time in mA(ms).● For checking a loop tester.● For wiring check (Phase, Neutral, Earth).● For checking continuity.● For checking insulation (The maximum is 1.2kV).● For checking UK16th edition.● Safety standard: EN 61010-1 / EN 61326-1
-
Morris Products Inc.
oltage DC 600V with basic accuracy ±(0.5%+5d)Voltage AC 600V with basic accuracy ±(0.8%+5d)Current AC 400V with basic accuracy ±(2.50%+6d)Slimline Electric Clamp Meter Resistance 20M ohms with basic accuracy ±(1.0%+4d)Continuity buzzer sound at 300 ohmsDiode test current 0.3mA; Open circuit voltage 1.5VAccessories: test leads, carrying case, 2(AAA) 1.5V batteriesSize:8-1/16"L x 2-3/4"W x 1-1/2"HSlimline Electric Clamp Meter Weight: 7oz.2000 LCD display countsDecimal Point ReadingsDisplay with backlightData holdMax holdAuto power offLow battery indication
-
785068-01 -
NI
The PXI Displacement Input Module supports 4-, 5-, and 6-wire AC linear variable differential transformer (LVDT) and AC rotary variable differential transformer (RVDT) measurements. The module simultaneously samples each analog input and sets the excitation frequency and voltage for each channel independently. You can set different timing, triggering, and sampling modes for each channel independently. Diagnostic features include self-calibration, overcurrent detection, and open coil detection.The PXI Displacement Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
ST-3347W -
Standard Instruments Co., LTD.
This clamp meter provides accurate AC, AC/DC current and voltage readings regardless of the waveforms. This meter can use in most industrial and commercial applications where non-linear loads distort the current or voltage waveform. Reliable operation. Features accessories such as test leads, carrying case and temperature probe.
-
FEV100 -
Fluke Corporation
Test the safety and performance of a type 1, level 1 or level 2 electric vehicle ac charging stations (EVSEs) with the Fluke FEV100. This test adapter simulates the presence of an electrical vehicle, allowing you to conduct tests in combination with appropriate test instruments such as a digital multimeter or oscilloscope.
-
Acromag, Inc.
Process limit alarms monitor sensor or process current input signals and trip a relay output if the input exceeds a user-defined hi/lo setpoint limit. Select from AC-, DC, and loop-powered models. Configuration is easy with Windows software, push-buttons, switches, or pots for settings depending on the series.
-
HH2103A -
Colluck Company Limited
Basic Accuracy 1.0%. LCD display 2000 count, 12.8mm figure height. Manual Ranging at your choice (19 Range). Higher Voltage test up to AC 750V and DC 1000V. Higher Current test up to 10A. Resistance test up to 2000KΩ
-
HH3211D -
Colluck Company Limited
High Accuracy (basic accuracy 0.5%). Large LCD display 2000 count. Convenient Auto Ranging. High Voltage test up to AC 600V and DC 600V. Resistance test up to 20MΩ. Diode test and audible continuity check. Low Battery Indication