Filter Results By:
Products
Applications
Manufacturers
AFDX
Avionics Full Duplex Switched Ethernet
See Also: Avionics, Ethernet, Avionics Full Duplex Switched Ethernet
- Pickering Interfaces Inc.
product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 4 Channel
40-201-004
This high bandwidth differential fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
product
AFDX®/ARINC664P7 Modules
AIM’s AFDX®/ARINC664P7 test, simulation, monitoring and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with multiple processors for real time bus protocol and application support, massive memory and IRIG-B time code encoder/decoder functions are standard. Versions are available to support the Boeing specific ARINC664P7 extensions.
-
product
AFDX ® /ARINC664P7 Networks Test, Simulation, Monitoring & Analyzer
ACE-FDX-3U-2
AFDX®/ARINC664P7 Test and Simulation module for PCIe x1 with 2 full duplex ports programmable for 10/100/1000 MBit/s. Versions available for both Airbus and Boeing variants of ARINC664P7. Test, verification and simulation of AFDX®/ARINC664P7 End Systems, Switches and Networks. Support for Single or Redundant AFDX®/ARINC664P7 operation. Support for Boeing ARINC664 extensions for EDE at the hardware interface layer.
-
product
2 Port 10/100/1000Mbit/s AFDX®/ARINC664P 7Test, Simulator And Monitor Module For XMC
AXC-FDX-2/B
AFDX®/ARINC664P7 Test and Simulation module for XMC with 2 full duplex ports programmable for 10/100/1000 Mbit/s. Versions available for both Airbus and Boeing variants of ARINC664P7.
-
product
Time-Triggered Ethernet / ARINC 664 Part 7 (AFDX®) / IEEE 802.3 Ethernet Deterministic Communications
TE2
Module TE2 is one of NAI's latest generation of advanced function Configurable Open Systems Architecture™ (COSA®) compatible modules. The TE2 is a certifiable, single-port, tri-redundant, deterministic Ethernet communications interface module that supports TTTech’s certifiable TTEthernet® End System product consisting of three traffic classes: SAE AS6802 (Time-Triggered Ethernet), ARINC 664 Part 7 (Avionics Full-Duplex Switched Ethernet (AFDX®), and/or IEEE 802.3 best-effort protocol. By supporting all three traffic classes, NAI's TE2 is the ideal solution for current users of IEEE 802.3 Ethernet, who plan to upgrade to Deterministic Ethernet (ARINC 664 Part 7 (AFDX®) or Time-Triggered Ethernet SAE AS6802) protocols in the future at any time without changing hardware.
-
product
USB SmartCable For AFDX®/ARINC664P7 Test And Simulation With 2 Full Duplex Ports Programmable For 10/100 Mbit/s
ASC-FDX-2
USB SmartCable for AFDX®/ARINC664P7 Test and Simulation with 2 full duplex Ports programmable for 10/100 Mbit/s. Versions available for both Airbus and Boeing Variants of ARINC664P7.
-
product
BusTools Software Analyzer
AFDX-A
BusTools/AFDX-A is a Windows 7/10-based GUI application solution from Abaco Systems that establishes new levels of power, flexibility and ease-of-use for AFDX (Avionics Full Duplex Switched Ethernet) traffic monitoring, analysis and simulation. Available for use with our powerful CNIC interface, BusTools/AFDX offers an intuitive interface to view, log, analyze and generate AFDX network traffic at the Adapter, End System, Virtual Link (VL) and Port levels. Contact Goleta factory for listing of supported products.
-
product
Avionics Communications Bus
ARINC-664 p7 (AFDX)
ARINC-664 p7 (AFDX) is an avionics communications bus that has been mandated by both Boeing and Airbus for use in new civilian avionics designs. The following tutorial provides a brief introduction to the central features of AFDX.
-
product
AFDX/ARINC664
With both hardware-based and software loadable AFDX, we support AFDX across evolving platforms to protect your avionics investment.
-
product
2 Port 10/100/1000Mbit/s AFDX/ARINC664P7 Test, Simulator And Monitor Module For PMC
AMCX-FDX-2/B
AFDX®/ARINC664P7 Test and Simulation module for PMC with 2 full duplex ports programmable for 10/100/1000 Mbit/s. Versions available for both Airbus and Boeing variants of ARINC664P7.
-
product
2 Port 10/100/1000Mbit/s AFDX/ARINC664P7 Test, Simulator And Monitor Module For PCIe
APE-FDX-2/B
AFDX®/ARINC664P7 Test and Simulation module for PCIe x1 with 2 full duplex ports programmable for 10/100/1000 Mbit/s. Versions available for both Airbus and Boeing variants of ARINC664P7.
-
product
SNMP & CLI Development
*Monitoring Windows and Linux Servers using secure SNMPv3*Windows and Linux SNMP SubAgent Development Tools*Embedded SNMPv3 and CLI Code Generators*Avionics AFDX / ARINC664 & SNMP*NTCIP Transportation SNMP
-
product
PCI Generic Carrier Cardfor PMC (PCIbus Mezzanine Card) Modules
ACP-1
PCI generic carrier card for PMC (PCIbus mezzanine card) with 1 PMC slot. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
-
product
CompactPCI (3U) Generic Carrier Card For PMC(PCIbus Mezzanine Card) Modules
ACC-1
cPCI (3U) generic carrier card for PMC (PCIbus mezzanine card) with 1 PMC slot. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
-
product
PCI-Express Generic Carrier Card
ACPe-1
PCI-Express generic carrier card for PMC (PCIbus mezzanine card) modules with 1 PMC slot. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
-
product
VME Generic Carrier Card For PMC(PCIbus Mezzanine Card) Modules
AVC-2
VME64x (6U) generic carrier card for PMC (PCIbus mezzanine card) with 2 PMC slots. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
-
product
Development Switch
AFDXSwitch Lab v2.0
The AFDXSwitch Lab v2.0 is identical to the TTESwitch A664 Lab v2.0, which fully supports AFDX® and operates in accordance with all requirements specified in the ARINC 664 part 7 standard. Features include traffic policing and frame filtering functions as well as integrity and error checking of frames. Additionally, the switch comes with advanced features like 1 Gbit/s speeds and flexible physical layer configuration. The TTESwitch A664 Lab v2.0 is based on the TTESwitch Module A664 Pro, thus providing the full range of technical functionalities of TTTech’s certifiable AFDX switch modules and making it the optimal switching solution for a large variety of different application areas.
-
product
PCI-Express Generic Carrier Card
ACPx-1
PCI-Express generic carrier card for XMC (PCI-Express bus mezzanine card) with 1 XMC slot. Modular solution combines any AIM XMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party, VITA 42.3 compliant XMC module.
-
product
Interface
RCNIC-A2PAX
The RCNIC platform is a high performance, PCI module (PMC on carrier card) for the AFDX / ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation.
-
product
PCIe Board
79G5P
The 79G5P-TE2C0 is a full-height, half-length, PCIe board fitted & configured with the NAI TE2 function module. The TE2 is a single-channel, tri-redundant, Ethernet communications interface module that supports three traffic classes: Time-Triggered Ethernet SAE AS6802 (TTEthernet™), ARINC 664 Part 7 and Avionics Full-Duplex Switched Ethernet (AFDX®) and IEEE 802.3 protocol.
-
product
Data Loading Products
TechSAT's data loading products are available to support all standard ARINC data loading protocols: ARINC 615/615A/826/844 for ARINC 429 and Ethernet based data loading. For next generation aircraft, TechSAT's data loading solutions bring portability to data loading over the new generation of avionics bus and network types: AFDX®/ARINC 664, Avionic & Deterministic Ethernet, TTP, and ARINC 825/CAN
-
product
Multibus Development and Test Tool for ECUs and Networks
CANoe
The versatile software tool for development, testing and analysis of ECUs and entire networks. Bus systems: CAN, CAN FD, LIN, MOST, FlexRay, Ethernet, WLAN, Car2x ITS G5, AFDX, J1708, ARINC429 > Protocols: TCP/IP, SOME/IP, CANopen, J1939, ISO 11783, J1587, MCnet, GMLAN, K-Line, CANaerospace and ARINC 825. Others upon request.
-
product
Development Switch
AFDXSwitch Lab
The AFDXSwitch Lab operates in accordance to all requirements specified in the ARINC 664 part 7 standard. Features include traffic policing and frame filtering functions as well as integrity and error checking of frames. Additionally the switch comes with advanced features like 1 Gbit/s speeds, flexible physical layer configuration and extended environmental ratings. The AFDXSwitch Lab provides the full range of all technical functionalities of TTTech’s certifiable AFDX production switches, making it the optimal switching solution for a large variety of different application areas.
-
product
PXI Differential Fault Insertion Switch Modules
Pickering's PXI Differential Fault Insertion Switch Modules support multiple channels of two-wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to externally applied fault conditions. *Two module types are available: Two wire fault insertion module suitable for CAN Bus and FlexRay.*High bandwidth two wire fault insertion module suitable for Gigabit Ethernet, AFDX and BroadR-Reach.
-
product
PXI Data Communications Multiplexer
40-736-001
This Data Communications Multiplexer is designed specifically for multiplexing or de-multiplexing up to 32 differential signal pairs having controlled 100 differential impedance. The multiplexer can be configured under software control to provide switching for 32 differential pairs, 16 dual differential pairs and 8 quad differential pairs. The dual and quad versions are particular well suited for providing switching of AFDX, BroadR-Reach and Ethernet signals. To support Ethernet applications, the design includes a switching network that simplifies the swapping of Tx and Rx pairs to simulate the effect of Ethernet crossover cables.
-
product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 4 Channel
50-201-004
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, Broad R-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 8 Channel
50-201-008
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
product
PCI Fault Insertion Switch Range for Differential Serial Interfaces
50-200/201
Pickering Interfaces, a leading supplier of modular signal switching for electronic test and simulation, is expanding its range of PCI Fault Insertion switching with the introduction of two new modules (models 50-200 and 50-201) designed for use with differential serial interfaces. PCI Fault Insertion Switch Cards for Differential Serial InterfacesThe new modules include the Differential PCI Fault Insertion Switch (model 50-200) which is designed for lower data rate serial interfaces such as CAN and FlexRay, and the High Bandwidth Differential PCI Fault Insertion Switch (model 50-201) which is designed for higher data rate serial interfaces such as AFDX and 1000BaseT Ethernet. Each module allows the introduction of fault connections that include data paths open, data paths shorted together, and data paths shorted to externally applied faults such as power supplies and ground. The software driver defaults to a protective mode where conflicting faults are prevented to avoid accidentally shorting unintended paths, such as power to ground. A separate mode allows complete freedom in setting fault patterns.
-
product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 8 Channel
40-201-008
This high bandwidth differential PXI fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
