Showing results: 1021 - 1035 of 1737 items found.
-
AMM-1 -
D'Amore Engineering llc
The purpose of this tool is to enable the user to: Measure True Amplifier Power output into any load reactive or resistive Measure Common DC voltages Measure DC voltage drops during quick transients on cable runs or battery / charging systems Measure Impedance of speakers at any power or frequency from 20Hz - 1kHz (box rise) Measure Phase Difference between Voltage and Current into reactive loads (Power Factor) Find Tuning Frequency of subwoofer enclosures Tune subwoofer enclosures for maximum power transfer Measure AC Volts (amplifier output) Measure AC Amps (amplifier output)
-
Analog Devices Inc.
Analog Devices offers RF Front-End ICs for phased array antenna solutions. These RF Front-End ICsare placed right at the antenna element and can quickly switch between transmit and receive functions in radar applications. The power amplifier on the transmit side is highly efficient operating in short pulse durations. The low noise amplifier on the receive side has a low noise figure with high linearity so that it won’t distort the incoming return signal. The RF Front-End IC also incorporates a high performance switch to toggle between the transmit and receive paths. Highly integrated planar phased array antennae need small form factor solutions, and Analog Devices has integrated the switch, low noise amplifier, and power amplifier into a small surface mount package as well as the decoupling capacitors, providing an optimal solution.
-
Menlo Systems Gmbh
Carrier envelope phase stabilization (CEP) is an enabling technology for metrology and for the generation of few cycle pulses. As one of the pioneers in the field we have developed products that allow to stabilize the carrier envelope phase of light pulses of few cycle pulse oscillators and amplifiers.
-
DS4 -
ELM Video Technology, Inc.
DMX 512 1x4 TVS Splitter 1 in 4 out splitter (distributor, buffer, amplifier, booster) that takes the output of a any DMX 512 device (lighting console e.g.) and actively splits the signal providing 4 separate DMX 512 outputs.
-
McLAREN Applied Technologies
The output voltage of this sensor changes with absolute pressure. An internal amplifier creates a single-ended, amplified output in the 0 to 5 Volt range, so the sensor can be connected directly to most control units. The body and diaphragm are impervious to chemical attack by standard motorsport fluids.
-
Dx10-SI-HiTEMP -
Teledyne LeCroy
The 90 cm HiTemp cables and Solder-In lead can be used for controlled situations where the differential amplifier module needs to be removed from the extreme temperature environment. Ideally suited for testing scenarios where the temperature can fluctuate from -40 °C to +105 °C.
-
Dx20-SI-HiTEMP -
Teledyne LeCroy
The 90 cm HiTemp cables and Solder-In lead can be used for controlled situations where the differential amplifier module needs to be removed from the extreme temperature environment. Ideally suited for testing scenarios where the temperature can fluctuate from -40 °C to +105 °C.
-
Model 615-10 -
TREK, INC.
The Trek Model 615-10 is a precision high voltage AC/DC generator and amplifier system used in a broad range of R&D and production applications which include providing operating potentials required for electrostatic charger roller devices as used in electrophotographic processes.
-
piezosystems jena, Inc.
The d-Drive® modular piezo controller system from piezosystem jena combines the highest positioning accuracy with a personalized design. A complete system contains an EDS interface (with display and controls), paired with a variety of EVD digital amplifiers, all contained in a 19-inch rack-case.
-
GT Series -
Keyence
General Purpose Digital Contact Sensor. Tough, Rugged: IP-67 Enclosure Rating. Error-free Design w/ Co-transformer method. Total Cost Reduction w/ simplified set-up. Easy and simple set-up. One-push zero point adjustment. Data communication with 10 amplifiers
-
Model 110 -
Shb Instruments
The Model 110 Magnetic Measurement System is a very high field version of our industry-standard MESA, designed specifically to measure high-coercivity samples. It uses powerful amplifiers and specially designed water-cooled solenoid assemblies to achieve the magnetic fields required by state-of-the-art material.
-
Kuhne electronic GmbH
Kuhne electronic Signal Generators are available in the following variations:RF Generator as Compact Module in the form factor of a power amplifier (frequency and power can be adjusted)Laboratory Instrument for immediate use with self-explaining user interface for adjustment of frequency and power as well as multiple monitor information possibilities
-
TPA2005D1 -
SparkFun Electronics
This tiny audio amplifier is based on the Texas Instruments TPA2005D1. Its efficient class-D operation means low heat and long battery life. It can drive an 8-Ohm speaker at up to 1.4 Watts; it won't shake a stadium, but it will provide plenty of volume for your audio projects.
-
ITD 1024 -
NOFFZ Computer Technik GmbH
ITD 1024 is an off-the-shelf solution for A²B®, an emerging automotive audio bus. In combination with a comprehensive set of software tools, ITD 1024 allows rapid testing of various A²B® components such as audio speakers, amplifiers, microphone arrays, sensors, and actuators.
-
Digilux 9500 -
Instrument Systems Optische Messtechnik GmbH
The Digilux 9500 of the Optronik line is a high caliber luxmeter for the precise measurement of illuminance, luminousintensity in the lab, or determination of luminous flux with an integrating sphere. It is equipped with a state-of-the-art photocurrent amplifier and microprocessor technology, and offers multiple operating and display functions with an excellent price-performance ratio.