Showing recent results 1576 - 1590 of 3190 products found.
-
NCS Testing Technology Co., Ltd.
A graphite crucible is placed on the holder and the impulse furnace is closed by the pneumatic system.The sample of typically 1g is dropped into the loading mechanism after weighing. The outgassing phase starts the analysis cycle to clean the furnace from Oxygen and Nitrogen out of the air.The sample loading mechanism release the sample into the now cleaned crucible.The oxygen content of the sample react with the Carbon from the graphite crucible to CO and the Nitrogen content to elemental N2 gas at temperatures of about 2200°C. Both gases were transported by the Helium carrier gas to the oxidation furnace where Copper Oxide converts the CO to CO2. This CO2 concentration is analysed by an infrared absorption detector and the Oxygen concentration is calculated.The Nitrogen is analysed afterwards by a thermal conductivity detector.
-
CS-3000 - NCS Testing Technology Co., Ltd.
A sample of typically 0.5 to 1.0g is weight into a crucible together with 1.5g of tungsten accelerator. This crucible is placed on a pedestal which drives it into an induction furnace by a pneumatic system. The sample is completely burned in the furnace by pure Oxygen.The Carbon of this sample is oxidized to CO2 and the Sulphur content to SO2. Dust and other particles are trapped in a filter system.The CO2 and SO2 is transported from the furnace in the Oxygen carrier gas to the infrared adsorption detectors.The actual gas concentrations are determined and the data are send to the PC.The operation software is calculating the results after integration of the whole signal peaks. A calibration with known samples builds up a database which created the necessary accuracy and precision. The burned crucible is driven out of the furnace by the pneumatic system and disposed by an operator. The furnace and gas flow system is purged after analysis by clean Oxygen to avoid any interference (memory effect) of the individual samples.
-
Spanawave Corporation
Spanawave's test port extension cables are the perfect alternative to over-priced models from other manufacturers. These test cables provide the utmost precision in vector measurements in the lab and during calibrations.
-
4500C - Boonton Electronics
The Boonton Model 4500C is the instrument of choice for capturing, displaying, analyzing and characterizing microwave and RF power in both the time and statistical domains. It is ideal for design, verification, and troubleshooting of pulsed and noise-like signals used in commercial and military radar, electronic warfare (EW), wireless communications (e.g., LTE, LTE-A, and 5G), and consumer electronics (WLAN), as well as education and research applications.
-
NXA-26 - Eastern-Optx
This new NXA-26 is a sea-change in Phase Noise Test Systems. Making both residual and absolute noise measurements out to 26.5 GHz, this self-contained instrument uses either internal or external references with cross correlation for maximum dynamic range. The NXA-26 combines over 25 years of Phase Noise Measurement Technology with an easy to navigate user interface. System operation requires minimal training that will have you making measurements in minutes.
-
Svan 958A - Acu-Vib Electronics Acoustic & Vibration
The SVAN 958A is an unique four-channel instrument offering 20kHz-band sound & vibration analysis. It is a perfect choice for allapplications that require simultaneous class 1 noise measurements & tri-axial vibration assessment. Each of four input channels
-
LMFA-21 - AmFax Ltd
Amfax introduce the latest PXI based High Performance Low and Mid Frequency Analysis System operating from 100Hz TO 2MHz with an extremely low noise floor. This high accuracy measurement instrument utilizes the National Instruments Function Generator and Flex Digitizer to optimize your frequency related product performance. Using the industry standard PXI platform enables us to offer the system a fraction of the cost of other typical two box solutions.
-
MiniSonic MS10 - Lindos Electronics
The MiniSonic MS1/MS10 Audio Analyser/Studio Aid is a complete, hand held, two-channel analogue audio test set that measures frequency, frequency response, phase, level, noise, distortion, crosstalk, speed and path latency (delay).As well as being a quality tester it's a precision line-up tool, a stereo PPM, a balanced-unbalanced convertor (both ways),a stereo mic preamp, a headphone amp, and a level convertor.
-
Streamline P937XA - Keysight Technologies
The Keysight compact VNA offers the good performance on key specifications such as dynamic range, measurement speed, trace noise and temperature stability. It utilizes the same measurement science with the trusted Keysight VNAs, you can have consistent measurement results. Measurement speed: 24 msec (201 points, full 2-port cal, 100 kHz IFBW). Dynamic range: >; 114 dB at 9 GHz > 110 dB at 20 GHz (10 Hz IFBW).
-
WavePad - NCH Software Pty Ltd
WavePad audio editing software is a full featured professional sound editor for Windows and Mac OS X. It lets you make and edit voice and other audio recordings and also comes with a wide range of powerful audio effects including echo, amplification and noise reduction.
-
Keysight Technologies
Choose from six frequency ranges up to 26.5 GHz, pay only for what you needGet the best PXI VNA speed, dynamic range, trace noise and stability; improve accuracy, yield & marginsOffers full 2-port S-parameters in one PXI slot; have more slots available in your PXI chassisProvides trusted Keysight measurement science and calibration - get measurements you can count onCascade multiple modules for true multiport applications - test with full N-port capability
-
Aarohi Embedded Systems Pvt. Ltd
Portable.Easy to install.Computer interface through rs232/rs485.Digital noise filtering, direct measure up to 400amp’s.TRMS measurement, class of accuracy: 0.2%User friendly operation.Digitally calibrate.Micro controller based design.
-
WinTek s.a.s.
The NVA instrument is generally composed of a personal computer equipped with one or more data acquisition board, a conditioning interface and / or to the transmitters power and finally a series of libraries of application software dedicated to the type of measurement to be made. the type of personal computer can be either a desktop, notebook or portable and depending on the particular requirements, you can use the PXI architectures.
-
WSUB1G - Seeed Technology Inc.
Frequency band: 240 - 960 MHzFrequency span: 112KHz - 100MHzGraphics LCD 128x64 pixels, great visibility outdoorsPC Windows client supports Windows XP/Vista/Win7 both 32 and 64bitsBacklight for great indoor visibilityStandard SMA 50 ohms connector, wideband Nagoya NA-773 telescopic antenna includedAmplitude resolution: 0.5dBmDynamic range: -115dBm to 0dBmAbsolute Max input power: +5dBmAverage noise level (typical): -110dBmFrequency stability and accuracy (typical): +-10ppmAmplitude stability and accuracy (typical): +-3dBmFrequency resolution: 1KhzResolution bandwidth (RBW): automatic 2.6Khz to 600KhzWeight: 185gSize: 113x70x25 mm
-
RAE - Yoshimasa Electronic Inc.
Advanced sound recorder/analyzer with the latest environmental noise measurement technology. Used for a wide scope of application in sound system engineering.
