Filter Results By:

Products

Applications

Manufacturers

Analyzers

examine data methodically by separating into parts and studying their interrelations. AKA: Analysers

See Also: Analyze, Analytics, Analysis


Showing recent results 2881 - 2895 of 3078 products found.

  • Dual-Port Simulator/Analyzer Test & Simulation PXI Express Module

    PXIe-FC4 Simulyzer™ - Avionics Interface Technologies

    3U PXIe form factor will fit into any PXIe or hybrid slotSupports Point-to-Point, Switched Fabric, and Arbitrated Loop topologiesTwo independent Fibre Channel portsTwo SFP sockets accept fiber or copper transceiversEach port supports 1, 2, and 4 Gbps speedsComprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) framesTriggering and FilteringError Injection on any Header or Payload ParameterData Capture to on-board memory or disk fileLive Capture and Current Value MonitoringIRIG-B Time Code Encoder/Decoder for Data CorrelationIn-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AVSupports HS-1760E applications, including AS5653, AS5625, and AS5627fcXplorer Windows-based FC Simulator and Analyzer Test Software

  • Amplifier, Switch and Test Box

    CLIOQC Model V - Audiomatica

    The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.

  • Condition Monitoring & Machinery Diagnostics Tools

    Oneprod - Vibralign Inc.

    The ONEPROD line features two portable tools, HAWK and FALCON, and two online systems, EAGLE and MVX. All four are supported and connected by the NEST software platform, which serves as an analysis and reporting interface as well as a database for measurement data. The NEST can be deployed either as a cloud-based app, installed to a server, or loaded onto a single computer. Each ONEPROD tool is designed to fill a specific niche or gap in an overall predictive maintenance plan-of-attack. The HAWK takes the mystique out of vibration analysis by performing complex analysis algorithms in seconds to quickly deliver machine health diagnoses, all while the user is standing next to the machine. The FALCON, with its built in stroboscope, camera, and pyrometer, is an all-in-one portable toolbox for performing route-based vibration analysis. The EAGLE is a wireless online vibration and temperature monitoring system that can monitor machines in confined or hard to reach spaces remotely. The mighty MVX is a powerful and intelligent multi-channel data analyzer that gathers multiple data-types, including vibration, IEPE, and voltage, continuously in real-time. The NEST software allows each of these tools to communicate and share data with each other, creating an airtight, fully integrated condition monitoring program.

  • Mobile Gas Leak Detection System

    ABB Ability - ABB Ltd.

    ABB Ability mobile gas leak detection system uses ABB’s patented Off-Axis Integrated Cavity Output Spectroscopy (OA-ICOS) technique which has a sensitivity and precision more than 3000 times greater than legacy methods. This enables identification of leaks several hundred feet away from the source. Current traditional leak detection technology is slow, laborious and costly. Operators walk on foot near the pipeline with hand-held sensors making paper-based reports.This is slow and can lead to dangerous leaks being missed or not identified in a timely manner. ABB’s Ability mobile gas leak detection system delivers a low cost per leak solution with low false positives. Reporting includes mapping of the leaks available via a mobile app and measurements as Cloud-based service. The system consists of ABB’s Methane/Ethane Analyzer, a GPS, a sonic anemometer and proprietary leak detection software that presents real-time geospatial maps of multiple gas concentrations in real time. The software’s sophisticated leak detection algorithm combines the system’s measurements of gas concentrations (CH4, C2H6), local coordinates (GPS) and local wind velocity (sonic anemometer) to estimate the location of the leak. Readings are stored in the device and can be transmitted in real-time to the cloud for centralized monitoring.

  • Near Field Probes 30 MHz up to 6 GHz

    XF1 set - Langer EMV-Technik GmbH

    The XF1 set of near field probes consists of 4 passive near field probes and one passive E field probe for making measurements in the development phase of the magnetic and electric fields in ranges from 30 MHz to 6 GHz. Due to their integrated impendance matching, the probes are less sensitive in the lower frequency range than the RF type probes. The probe heads of the XF1 set allow for the step by step identification of interference sources of the magnetic field on an electronic assembly. At first, for example the XF-R 400-1 detects the fields which the assembly emits in total. Next, using higher resolution probes the interference sources can be more precisely detected. The E field probe is used for the detection of electric interfering fields near the assemblies. With trained use of the near field probes, field orientation and field distribution can be detected. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They have an internal terminating resistance.

  • Portable Test Platform

    FTB-4 Pro - EXFO Inc.

    The FTB-4 Pro is the latest addition to EXFO’s test orchestration portfolio which transforms business as usual into smarter, scalable network testing that significantly increases operational efficiency and provides vital insights into field operations, network performance and service delivery. The 4 slot modular FTB-4 Pro platform enables a unique combination for 100G commissioning, turn-up and troubleshooting which includes the FTBx-88200NGE 100G Multiservice tester (with iOptics transceiver validation software) and the FTB-5240S-P optical spectrum analyzer. There is no need to carry additional platforms or swap modules for unmatched transport and spectral testing on a single platform that no one in the industry can offer. The versatile FTB-4 Pro platform supports a wide range of modules for field testing, data center interconnect, submarine testing, and lab applications for maximum flexibility and ROI across all phases of the service delivery chain: development, deployment, maintenance and troubleshooting. Module combinations on the FTB-4 Pro can also include iOLM/OTDRs, market leading OLTS for fiber characterization, dispersion solutions and other transport modules all with compatibility with EXFO’s market leading fiber inspection probes.

  • 1.0mm Flexible VNA 110 GHz Precision Cables

    Pasternack Enterprises, Inc.

    Pasternack's high-performance, flexible VNA test cables operate at up to 110 GHz and deliver precise results for testing using a coaxial cable and 1.0 mm stainless steel connector interface. The coaxial cable is covered by a non-conductive Nomex outer sleeve. In addition to the Nomex, a light-duty armoring protects the cable, while maintaining a 0.27-inch diameter and improving stability during flexure. These cables feature 50 Ohm impedance, a maximum VSWR of 1.5:1 and excellent phase/amplitude stability under flexure. Our flexible 1.0 mm VNA test cables operate over a wide range of temperatures from -65C to +125C. They are RoHS and REACH compliant. Each cable assembly is fully tested and comes with serialized test data. These cables are available in standard 6-inch and 12-inch lengths with male-to-male or male-to-female configurations. These VNA test cables are designed to deliver precision testing results for Vector Network Analyzer (VNA) testing, semiconductor probe testing, automotive radar testing and military radar testing.

  • Gas Detectors

    PCE Instruments

    At PCE Instruments you will find professional gas detectors for daily company use. Here you will find gas Detectors Profeesional Gas Analyzers (Gas Detectors). that meet industry standards relating to personal safety and that are mainly used to detect and measure levels of methane, hydrogen sulphide, carbon monoxide, oxygen and 50 other gases. The auto-calibration function allows for easy calibration of the gas detector. Some of them also possess the ability to store values and can later transfer data to a computer. One accessory is the manual aspirator, with this device, you can draw gas directly into the Detector via a 2m long tube with which you will be able to measure gas levels without having to be in direct contact to the gas source or to be able to determine the levels of gas in places that are difficult to access. Furthermore, we have a series of fixed installation Detectors available you can use independently or in conjunction with a gas detection installation. These Detectors can provide readings with or without a display, via data output.

  • VXI Video Processor System

    Model VXI 65VP1 - North Atlantic Industries

    NAI’s 65VP1 is a Video Processor System (VPS) on a VXI board. Capable of highly accurate video stimulus and measurements, this state-of-the-art instrument is the culmination of over three generations of Automatic Test Equipment (ATE) development programs. It provides increased functional density, and it reduces power consumption, size, and cost of the overall system. The 65VP1 is ideally suited for defense and commercial ATE programs, including television applications.With this multi-format video display generator and video signal acquisition system, videos can be composed with any possible sync format, rectilinear and polar raster, multi-image interactive stroke, and mixed video (stroke over composite, or stroke over raster). Video image acquisition and sync processor / analyzer functions are also supported. Either 6 output channels or 3 input channels are provided, along with extensive diagnostics. NAI’s Background Built-in-Test (BIT) continually checks on the health of each function and channel, and an initiated BIT function is also available through simple programming commands.

  • Emissions Test System

    PC-114 - Com-Power Corporation

    Perform Radiated & Conducted EMI pre-compliance testing at your facility up to 1 GHz. Com-Power PC-114 EMI emissions test system is a ideal solution performing pre-compliance EMC testing from 9 kHz - 1 GHz.. It has essential equipment needed for radiated and conducted EMI emissions measurements. The system includes a spectrum analyzer, antennas, near field probes, a preamplifier, LISN and a non conductive antenna tripod. Pre-compliance testing in EMC is a commonly used term not easy to define. In general, it implies testing done prior to formal testing for legal compliance. Formal legal compliance is performed at a facility designed and equipped with test instrumentation that is fully compliant with the applicable EMC standards. Such facility and instrumentation is capital intensive and can be expensive even to rent and not easily available. Compliance testing is performed per exacting requirements of the Standards and other reference documents adhering to the test methods and last detail. In addition, the test facility may require to be accredited by an accreditation body such as NVLAP, A2LA. Often it is desirable to know prior to compliance testing at such facility, whether a product is close to compliance and also how close. Pre-compliance testing is specially useful for specifications such as FCC, Part 15, EN 55022 or EN 55011 (CISPR 22 or CISPR11). Pre-compliance testing usually means using the full compliance methods but making a few educated compromises in use of site or equipment to reduce costs and testing time. Here are some benefits of pre-compliance testing.

  • Automatic Safety Analyser

    Rigel 277 Plus - Seward Medical

    The Rigel 277 Plus is a portable medical electrical safety analyser combining IEC/EN 60601-1 compliance with additional test facilities for IEC/EN 61010 (Laboratory Equipment) including Touch Leakage, Voltage Measurement and dedicated IEC 61010 Measuring Device (Body Model).

  • Apache Health Monitoring

    ApHeMo - KC Softwares

    ApHeMo is a Health Monitoring analyser for Apache HTTP Server. ApHeMo makes administrators able to improve security, reliability and to easily detect attacks from hackers (scans, potential backdoors...). ApHeMo is a must have tool for dedicated servers administrators.

  • Audio Analyser

    ATB 804 - Kirchner Elektronik

    *The measurement system existsMitteln of the ATB 802 USB Box, a Net PC with Windows XP and the program.*The calibrated measure microphone is included in the ATB 802PC bundle.*Professional measurement can not be easier. The price is very favourable.

  • Audio Analyser

    ATB PC Pro - Kirchner Elektronik

    The ATB PC Pro Measuring system is a professional Audio Analyser. The Windows program is combined with the computer’s soundcard, the measurement microphone, the Test-Box and the DVD (CD) for the signals forms an exact and extensive measurement system. The applications for the ATB PC Pro are the speaker development, room acoustic optimise, the installation of car sound systems, the setting of Surround reproduction systems and the noise analyser.

  • AUDIO ANALYSER

    K8098 - Velleman, nv

    Small and compact unit, ideal for panel mounting.Give your homemade audio gear a high-tech look. Upgrade existing equipment.