Showing results: 3091 - 3105 of 3973 items found.
-
6 Series -
Powermetrix Systems
Powermetrix extends its revolutionary line of handheld three phase analyzers with the PowerMaster® 6 Series, now with Powermetrix Remote Manager (PRM)®. PRM enables wireless control of essential and various metering site accuracy tests contained within the PowerMaster 6 Series.
-
TLF3000 -
Teledyne LeCroy
TLF3000 RF PHY tester is a wideband, ultra-high dynamic range 2.4 GHz software-defined receiver, signal analyzer and signal generator. It captures and analyses the entire 2402-2480 MHz band simultaneously providing RF PHY testing, signal generation, signal analysis in one powerful package.
-
Guangzhou Jumho Electric Co., Ltd.
IPTV Set-of-Box test system is general audio/video test system for IPTV RCA signal output. This system has these features: Based on high-speed, high resolution data acquisition board from National Instruments. It can support all video and audio parameters testing.High speed, 3x than traditional video analyzer and audio analyzer.
-
UC9110/UC9115 -
UC Instruments, Corp.
The UC INSTRUEMNTS UC9110/UC9115 DCA-M 10 GHz/14 GHz Optical & Electrical Sampling Oscilloscope is a high speed, performance, flexible one channel optical/electrical that can operate from 1.0 to 14.0 Gb/s (consult factory for higher or lower operation speeds). It is also a stand alone Eye-diagram analyzer test.
-
GL Communications Inc.
GL's protocol analyzer provides monitoring a communication link in accordance with industry protocol standards by non-intrusively tapping the network under test. The simple framework of the protocol analysis software helps you easily identify the improper sequence of protocol messages, and filter out frames causing the protocol violation.
-
GL Communications Inc.
GL's protocol analyzer provides monitoring a communication link in accordance with industry protocol standards by non-intrusively tapping the network under test. The simple framework of the protocol analysis software helps you easily identify the improper sequence of protocol messages, and filter out frames causing the protocol violation.
-
CH-6130/6140 -
Ono Sokki
The CH-6130/6140 charge converter is a simplified type of charge amplifier converting charge signal to voltage.It can be connected directly to an input BNC connector of a CCLD applicable equipment such as FFT analyzer or vibration comparator, enabling direct connection of a charge output pickup without suing a box type amplifier.
-
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Network analyzers are used to measure so-called scatter parameters (S-parameters). These describe the behaviour of electrical components with the help of wave magnitudes. Whether simple cables, filters, amplifiers or complex subsystems, the following applies to all these components: Different loads can have unseen effects on the measured values over time.
-
NEX DE -
Applied Rigaku Technologies, Inc
As a premium high-performance benchtop EDXRF elemental analyzer, the NEX DE delivers wide elemental coverage with an easy-to-learn Windows®-based QuantEZ software. Non-destructively analyze sodium (Na) through uranium (U) in almost any matrix, from solids and alloys to powders, liquids, and slurries.
-
ACM2543 -
Copper Mountain Technologies
ACM2543 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 44 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process.
-
ACM4520 -
Copper Mountain Technologies
ACM4520 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 20 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process.
-
ACM2520 -
Copper Mountain Technologies
ACM2520 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 20 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process.
-
ACM2506 -
Copper Mountain Technologies
ACM2506 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 6.5 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process.
-
ACM2509 -
Copper Mountain Technologies
ACM2509 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 9 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process.
-
A.H.Systems, Inc.
Conducted currents can be measured without making direct contact with the source conductor or metallic surface by means of clamp-on broadband current probes. The BCP-5xx EMC Current Probes are designed to permit field intensity meters, spectrum analyzers, and other 50W impedance instruments to measure quantitative magnitudes of current.