Showing recent results 3181 - 3193 of 3193 products found.
-
mOByDic-Kombi-Deluxe - Ozen Elektronik Inc.
This device is provided for official exhaust emission testing. a PC based software allows to implement country specific regulation.
-
mOByDic-5000 combi - Ozen Elektronik Inc.
This device is provided for official exhaust emission testing. a PC based software allows to implement country specific regulation.
-
Quadrupole Mass Spectrometer (QMS) - Protea Ltd
Quadrupole Mass Spectrometer Analyser System for low volume, quick responding gas measuring with large dynamic range Quadrupole Mass Spectrometer (QMS) for low volume, quick responding process gas measurement with large dynamic range.
-
SA3000 - Laplace Instruments Ltd.
The SA3000 is a powerful, fully featured, EMC analyser. It will measure both conducted and radiated emissions according to the international EMC standards. It enables the user to assess the EMC compliance of products quickly and with good integrity.
-
Laplace Instruments Ltd.
All commercial LISNs include an artificial hand connection and a transient limiter. This adds a 30dB insertion loss. A 30dB pre-amplifier is included which can be connected in the RF output feed to return the insertion loss to 0dB. The Voltage Probe requirement is covered by our PLIP (Power LIne Interference Probe). This fully meets the requirements of CISPR16, but has additional features:*Fully galvanic isolation between input and output (>1kV), for the safety of operator and analyser!*Shrouded safety clips for attachment to the line to be measured.*Filtered frequency response matched to Band A and B.*Current limiting on the output.*Visual indication of high voltage input.
-
Laplace Instruments Ltd.
The ease and effectiveness of conducted emission measurements can be enhanced by the use of appropriate filters. In particular, broadband noise below the frequencies of interest can cause limiting (compression) in spectrum analysers, distorting the measurements.
-
EA-300 - Laplace Instruments Ltd.
The EA-300 is a stand alone unit with internal firmware and a large colour display. It connects to the outputs from a standard LISN and feeds the results to any standard EMC analyser or receiver. The EA-300 prompts the user through the steps necessary to fully characterise the emissions from the EUT, then will output via the screen the recommended filter component values that would reduce these emissions to acceptable levels.
-
SA1002 - Laplace Instruments Ltd.
The SA1002 provides a high performance capability to measure the EMC compliance of your products. It covers the conducted emission and radiated emission bands to 1GHz, as required by most EMC standards. The included software is Windows compatible and simple to use. This powerful system automatically sets the analyser parameters to suit the test to be performed. Standard limits are available from simple pull-down menu. Results can be directly compared against these limits for easy checks on compliance status.
-
Laplace Instruments Ltd.
These Pre-Selectors are high specification, switched band filters which track the scanning of the EMC Analyser. Control is via USB link from the Laplace EMCEngineer software supplied with SA1002 and SA3000 analysers. Installation and operation is completely automatic, and the filters will synchronise with the analyser scan without any operator intervention. A front panel switch allows manual operation if required.
-
AC2000A - Laplace Instruments Ltd.
The Laplace Harmonics and Flicker analyser provides the user with a complete system for testing product compliance with IEC61000-3-2 and IEC61000-3-3. Quick and easy to use, the built-in screen provides a clear pass/fail indication of compliance status, plus a full listing of results for each harmonic, in either tabular of bargraph format. The instrument is properly configured to cope with fluctuating harmonics. The Flicker mode provides proper measurement of short term and long term parameters, using algorithms specified in IEC61000-4-15. In addition, inrush current measurements can be automated such that the product under test can be automatically cycled on/off with user entered time profiles.
-
MQC+ - Oxford Instruments plc
MQC+ benchtop NMR (Nuclear Magnetic Resonance) analyser for the measurement of oil, water, fluorine and solid fat in a variety of samples in a wide range of industries. The MQC+ replaces wet chemical analysis, which uses hazardous chemicals, and allows the measurement of more samples much faster. Unlike wet chemical methods, the MQC+ does not destroy the sample being measured. It can also measure physical properties including crystallinity and density of polymers.
-
ELE International
ELE international manufactures a comprehensive range of field and laboratory asphalt testing equipment to ensure compliance with quality and performance specifications. Traditional methods of binder content analysis involved the use of solvents, but due to environmental concerns ELE has developed an Asphalt Binder Analyser which uses an ignition method and thereby avoids the use of harmful solvents. Loss on heating and a rolling thin-film oven are used for testing bitumen, flash and fire point are measured with the Cleveland Flash Cup Apparatus, and the Ring and Ball test enables the measurement of the softening point.
-
NH3 Gas Analyzer - Protea Ltd
The Solus Multipoint NH3 Ammonia gas analyser is ideal for ambient air and livestock monitoring applications of Ammonia (NH3). The Solus is a complete transportable ammonia measurement solution for up to 10 sample points. Ammonia is a primary measurement parameter under the Verification of Environmental Technologies for Agricultural Production (VERA) Test Protocol for Livestock Housing and Management Systems.
