Showing results: 136 - 150 of 206 items found.
-
SAS-586 -
A.H.Systems, Inc.
This Standard Gain Horn Antenna will provide reliable, repeatable measurements. An ideal solution and a standard workhorse of any EMC test house for compliance testing. Features: 12.4 GHz to 18 GHz, Individually Calibrated, FCC, MIL-STD, VDE and TEMPEST Testing.
-
BBHA 9120 K -
Schwarzbeck Mess Elektronik
The BBHA 9120 K is a linear polarized high gain horn antenna for immunity testing at short distances, especially optimized forAutomotive 600 V/m Pulse Radar Test 1.2 - 1.4 GHz. Standard: General Motors: GMW3097, Ford: EMC-CS-2009
-
PANACEA Field Test -
Safran Federal Systems
PANACEA Field Test (PANACEA FT) is a software tool designed to allow for easy data collection from multiple receivers in a real-world environment where the GNSS receivers are connected to an antenna. All the data is logged, time-stamped, and automatically compared to the configured truth source.
-
Site VSWR -
Seibersdorf Labor GmbH
The Site VSWR measurement is done according to CISPR 16-1-4 in the frequency range from 1 GHz to 18 GHz using broadband omni directional antennas in horizontal and vertical polarisation. The volumetric test method is applied (test volume needs to be specified), test distance 3 m - any other distance upon request. The ground plane has to be covered with absorbing material.
-
Cuming-Lehman Chambers
It’s nearly impossible to perform VHF/UHF measurements in a rectangular chamber. In the 1960’s Emerson determined that tapering one end of an Anechoic Chamber would cause the chamber to act like an indoor ground reflection range.Tapered Chambers work very well at the lower frequencies. Their design forms a uniform illumination across the test region. The tapered end of the chamber forces the wall images close together forming a source antenna array. Tapered Chambers are usually a less expensive option compared to rectangular antenna measurement chambers or compact ranges.
-
Micropross MP500 PT1-NFC -
NI
Support for ISO 14443 A/B, ISO 15693, MIFARE™, FeliCa™. Measurement correlation with NFC Forum and EMVCo certification test bench. Automated test executive with ready-to-run test sequences. Reader/Writer and Card Emulation modes, resonance frequency measurements supported on same antenna. Embedded analog measurements - LMA, field strength, S11, Q factor, waveform characteristics. Physical parameter/waveshape characteristic definition
-
Kuhne electronic GmbH
Is a radio beacon, whose purpose is the investigation of the propagation of radio signals. Most radio propagation beacons use amateur radio frequencies. They can be found on LF, MF, HF, VHF, UHF, and microwave frequencies. Microwave beacons are also used as signal sources to test and calibrate antennas and receivers
-
LPSU -
AWT Global
Low PIM coaxial switch matrix 5 x 6 or 1 x 4 configurationFrequency range 698-2700 MHz.SCPI commands via Ethernet (wired or wireless).Significantly reduces test time for multi frequency PIM applications.Applications: ATE systems, multi-band antenna and component testing.
-
Saluki Technology Inc.
S5105 series microwave multifunctional analyzer has the wide frequency range from 30kHz to 40GHz. It integrates multiple functions such as dual-port vector network analysis, cable and antenna feeder test, vector voltage measurement, spectrum analysis, field strength measurement, and power measurement, providing you with powerful comprehensive test capabilities. S5105 series RF analyzer is widely used in the radar performance test and cable TV, wireless communication field.
-
XSeries -
Keysight Technologies
Get a powerful building block, whether you need a dependable LO or a scalable threat simulator More accurately simulate multi-emitter scenarios for radar, EW and antenna test with the fastest switching, phase coherency, and extensive pulse-modulation Test sooner and increase confidence in EW system performance by generating complex signal simulations when you need them Increase the reliability of your test system: the UXG is a slide-in replacement for legacy fast-switching sources
-
Microwave Instrumentation Technologies, LLC
AMETEK NSI-MI's world-class test facilities uses industry-leading equipment and instruments to support your specific needs. A2LA-accredited measurement facilities, combined with our expert staff of engineers, can tackle any unique test and calibration requirements with precision and accuracy. Our equipment is calibrated with NIST traceability providing you with the assurance that we can accurately and consistently characterize your antennas, radomes and other devices.
-
SC series -
ACECO Electronics Corp.
The Aceco SC-1 hand-held radio frequency counter is compact, truly pocket-sized, versatile test instrument designed for measuring any digital, on/off keying or analog signal on frequencies between 30 MHz and 2.8 GHz. Supplied as a complete with internal NiCd pack, AC wall charger and 7 section telescopic antenna.
-
AtlanTecRF
Atlantic Microwave’s Ethernet Controlled Signal Generator and Miniature Signal Generator provides economical and versatile solutions where there is a need to input microwave frequencies for test purposes at remote locations, antenna sites, equipment cabins and laboratories related to satellite communications, radar systems, EW systems, scientific apparatus and similar applications.
-
TS7124 -
Rohde & Schwarz GmbH & Co. KG
R&S®TS7124 RF shielded boxes enable reliable and reproducible measurements in shielded test environments. The R&S®TS7124 shielded box provides high shielding effectiveness, a good antenna coupling factor and a rugged mechanical design for reproducible results. RF test boxes have been designed not only for product designers or product optimization but also for production lines of wireless devices under test. The soft close feature makes the shielded box safer to operate.
-
LC-8120/LC-8220 -
Ono Sokki
The LC-8120/8220 is the GPS-based speedometers which measure speed and distance of moving objects with high accuracy. Support for GLONASS satellite which is not supported in the conventional model (LC-8100A/8200A) to ensure stable measurement. Antenna for LC-8220 (LC-0721) is smaller and lighter than the conventional antenna for LC-8200A (LC-0086) and it enables easy operation. The new antenna (LC-0721) is able to attach to the conventional unit of LC-8200(A) for measurement. The linearity of acceleration and angular speed are improved by using the standard IMU (inertial measurement unit) together with the optional high accuracy IMU. Also, by adding the high response IMU analog output function (option), the analog output frequency of the IMU data can be increased from 100 Hz to 500 Hz. A wide range of optional functions such as white-line detecting function (LC-0856), jerk measurement function (LC-0871) and average deceleration speed calculation (function in the LC-0831) are available for various automotive tests.