Showing results: 121 - 135 of 966 items found.
-
RH850/E2x -
Renesas Electronics Corp.
RH850/E2x microcontrollers are ideal for powertrain applications, have high operation processing performance for realizing new combustion systems for fuel-efficient engines, and built-in hardware for knock control such as a successive approximation A/D converter, delta-sigma A/D converter, cyclic A/D converter, Digital Filter Engine (DFE), and Advanced Timer Unit (ATU-V), and engine control such as fuel injection control.
-
Teradyne, Inc.
Teradyne's TestStation platform enables manufacturers to easily react to rapidly changing product requirements. From volume, mix and test complexity - there is a TestStation configuration to meet your production requirements at the highest fault coverage and yield rate. configurable from a range of a few test points for basic shorts detection up to more than 15,000 test points for more complex PCBAs.
-
142-5 -
Electronic Specialties Inc.
Flexible 1.5 inch silicon pins provide easy back probing connections for DMM and Scope measurements
-
325 -
Electronic Specialties Inc.
The EZ-Tach makes RPM measurements quick and easy. This is a very useful tool for tune-up and other diagnostic work where accurate RPM readings are required. Just clamp over any spark plug wire and get accurate RPM on conventional or DIS ignition systems. The unit also features a data hold function. The large 2000 count LCD display shows; RPM, function, data hold indication and low battery indication. The EZ-Tach is powered by one 9 volt battery. Battery and instructions are included.
-
NI
The PXI Automotive Ethernet Interface Module communicates with Automotive Ethernet so that you can use the NI‑XNET driver or standard networking drivers to develop applications that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). It provides up to four independent endpoints or up to two network terminal access points (TAPs). With onboard hardware timestamping and the ability to act as 802.1AS masters or slaves, the PXI Automotive Ethernet Interface Module can synchronize with an external network as well as the rest of a PXI system.
-
Pickering Interfaces Ltd.
Pickering's Switch Simulator Modules are designed for automotive test applications. These modules simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. They allow automotive I/O devices to be tested for correct operation under adverse conditions.
-
Microwave Factory Co,Ltd.
Anechoic Chamber room of most suitable Automotive devices EMI/EMS test of the method of ALSE, which meet the global standard like a 2004/104/EC, several emmission standard like a CISPR25 which automotive manufacturers in EU/USA refer to, Immunity standard like a ISO11452 and others for the Automotive devices.
-
786169-01 -
NI
2-Channel, 4-Port, 100BASE-T1 to 100BASE-TX Automotive Ethernet Interface Device—The IVN-8561 is an interface that converts 100BASE-T1 unshielded twisted pair (UTP) automotive Ethernet to standard 100BASE-TX Ethernet. It is ideal for developing applications that require automotive Ethernet to test and validate automotive electronic control units (ECUs). The IVN-8561 provides two channels to convert data between 100BASE-TX Ethernet and 100BASE-T1 Automotive Ethernet. Each 100BASE-T1 port can be configured as master or slave, using switches on the front panel. The IVN-8561 also provides LED on the front panel so that you can monitor the linkage and activity on the various ports.
-
Keysight Technologies
Keysight Technologies’ TS-5000 Family of Automotive Electronics Functional Test Systems helps automotive electronics manufacturers get their products to market faster by accelerating test system deployment. It utilizes common architecture and core instrumentations to offer maximum flexibility to keep pace with the dynamic changes in the automotive electronic industry.
-
-
-
Renesas Electronics Corp.
Renesas' portfolio includes automotive-grade multiple output regulators for use in TFT-LCD automotive applications.
-
STPL-30 -
EMCTEST
The GTEMCELL STPL-30 Stripline is designed to produce high electric fields over a controlled bandwidth. It is used to perform EMC measurements according to automotive and aerospace standards in order totest the immunity of automotive and aircraft equipment to radiated electromagnetic fields.The STPL-30 uses a dual-sided tapered adjustable feed design into a tunable transmission line.
-
77102 -
Gunson
This automotive current tester with LCD display, plugs directly into the fuse box and can be used on mini, standard and maxi fuse connections. Blades may get hot during use and care should be taken for 2mins whilst they cool down. Fits mini and maxi fuses. Current range 0-80AMP. Safe and easy way to check automotive current.
-
100BASE-T1 -
Prodigy Technovations Pvt. Ltd.
100BASE-T1 Automotive Ethernet Protocol Analyzer is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. Automotive Ethernet interface scales up to address current and future needs of in-vehicle bus speed requirement. Need for higher-speed in-vehicle bus is increasing to support feature-rich ADAS and connected vehicle needs. Two-wire full duplex 100BASE-T1 PAM 3 signaling is the choice of interface bus to address these needs