Showing results: 46 - 60 of 87 items found.
-
Bloomy Controls, Inc.
The Battery Fault Insertion Unit (FIU) provides intelligent switching of cell-simulation channels for the Battery Simulator 1200. The switching capability enables simulation of open-circuit and short-to-rail fault conditions on any cell channel for the purposes of battery management system (BMS) testing. Additionally, a four-wire auxiliary input allows you to connect an external digital multimeter (DMM) instrument to any cell channel for very high-accuracy bypass current and cell voltage measurements. Each FIU provides 24 independently-programmable cell-switching channels for one or two 12-cell Battery Simulator 1200 units. Additional Battery Simulator 1200 and FIU instruments can extend functionality up to 120 series-connected cell channels.
-
TT9103 -
Matco Tools
*Portable and water resistant trailer light tester and trailer brakes tester that allows the user to perform all testing functions without the use of the vehicle*Tests 7-spade, 6-round and 4/5-flat pin type trailer harnesses*Short circuit protection*Turn signal simulation and power verification LED*Water resistant*Trickle charger and trailer plug adapter includedInternal battery compartment (battery not included)
-
FTF-HP -
Bitrode, Inc.
Drive simulations with standard Electric Vehicle tests: FUDS, SFUDS, GSFUDS, DST and ECE-15LDrive Cycle TestingIntegration with motor test benchesCycle testing of EV/HEV Battery PacksBi-directional DC power supply
-
MOTOMEA
The MOTOMEA Electric Powertrain Dynamometer is part of a fully integrated modular system with hardware-in-the-loop testing. System capabilities include drive cycle and virtual test driving. Powertrain testing capabilities also include battery testing and simulation using bidirectional DC power supply.
-
BMS HIL -
Bloomy Controls, Inc.
The BMS Hardware-in-the-Loop (HIL) Test System is a high performance platform providing all necessary input signals used for battery pack simulation. A real-time operating system executes complex cell and pack models commonly used for BMS algorithm development and firmware regression testing.
-
OX-1 OxSim® -
Pronk Technologies Inc.
Test the complete SpO2 system, including the sensor, extension cable with the OxSim® Optical SpO2 Pulse Oximeter Simulator. Slips into your shirt pocket and operates easily with just two buttons on a single AA battery. The auto-detection of the Sensor type eliminates the need to select the manufacturer oximeter under test. The optional serial communications port enables users to expand simulation settings for Saturation, Pulse Rate, and Perfusion Index, ideal for applications where a wide range of simulations is needed.
-
Chroma ATE Inc.
DC power supplies offer many unique advantages for telecom, automated test system & integration, industrial, battery charge & simulation for hybrid cars and solar panel simulation. These advantages include high power density of 15KW in 3U, precision readback of output current and voltage, output trigger signals as well as the ability to create complex DC transient waveforms to test device behavior for spikes, drops, and other voltage deviations.
-
Ponovo Power Co., Ltd.
As the first power amplifier manufacturer in China, PONOVO has been offering various power amplifier products for customers in China and other countries since 2001. PONOVO has launched both conventional power amplifier for power system use and also 4-Quadrant power amplifier for more filed application, such as microgrid, windfarm, PV, HVDC, areospace, battery simulation, etc.
-
40-592A-113 -
Pickering Interfaces Ltd.
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
40-592A-104 -
Pickering Interfaces Ltd.
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
40-592A-107 -
Pickering Interfaces Ltd.
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
40-592A-114 -
Pickering Interfaces Ltd.
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
40-592A-106 -
Pickering Interfaces Ltd.
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
40-592A-105 -
Pickering Interfaces Ltd.
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
40-592A-013 -
Pickering Interfaces Ltd.
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.