Showing results: 106 - 120 of 632 items found.
-
CMx-SLx -
ADLINK Technology Inc.
The CMx-SLx is a PCI/104-Express Type 1 Single Board Computer (SBC) featuring the 64-bit 6th Gen. Intel® Core™ i3 processor (formerly "Skylake-H"), supported by the Intel® CM236 Chipset. The CMx-SLx is specifically designed for customers who need high-level processing and graphics performance in a long product life solution. The CMx-SLx Intel processor supports Intel Hyper-Threading Technology (i3-6102E = 2 cores, 4 threads) and 8 GB of soldered ECC DDR4 memory at 1866/2133 to achieve optimum overall performance.
-
Circuit Check, Inc.
Commonly referred to as In-Circuit Test (ICT), loaded board test can be defined as the task of measuring values of components that have been installed on a printed circuit board (PCB). A second basic category of loaded board test measures simple open and shorts on the board to verify manufacturability standards. Circuit Check supports all forms of in-circuit test strategies with its Performance Grade and Value Line test fixtures.
-
Arcadia Test
This useful tool will minimize induced stress on the board under test. The 3-D software will account for all components populated on the board, and probe force and push rod locations on the fixture. It uses this information to simulate the actual test to determine which area of the board is enduring too much stress and then provide suggestions to correct the situation. A damaged board could cost upwards of thousands of dollars and lost time. Including Board stress analysis in your test strategy is an excellent way to insure that your new test comes up fast, and without any stress related board damage.
-
Versi-Traq -
Automatiq Measurement Systems
A complete Ready-to-Wire Test Fixture including drilling, installed Pogo Pins, and board location hardware is available. Complete the Request for Quote form and send it to Automatiq for a fixed price quotation for a Ready-to-Wire test fixture for your board. We will need Gerber files for the board, a Test Point List with some way to relate the Test Points to the Gerbers, and a Sample Board populated as it will be tested in order to get started.
-
Acculogic, Inc.
Flying probe test systems require no test fixturing, have few restrictions on board access, and can test boards with virtually unlimited number of nets. These systems also allow developers to complete test programs in a short time.
-
Protector Adjustable Family -
Test Electronics
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
Protector Edge Press Family -
Test Electronics
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
Protector Press Rods Family -
Test Electronics
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
Pomona Electronics
Low-profile fine-pitch chips, desnely populated boards, or vertical boards, Pomona test clips connect you with confidence.
-
Pomona Electronics
Low-profile fine-pitch chips, desnely populated boards, or vertical boards, Pomona test clips connect you with confidence.
-
Huntron® Trackers® -
Huntron
Adding diagnostic tools to enhance your circuit board test capabilities is an important part of any electronic repair environment.Huntron Tracker power-off circuit board test uses analog signature analysis to detect and isolate component faults on boards beyond power-on functional testing. By comparing Tracker signatures from a working circuit board to the signatures of a non-working board, you can troubleshoot down to the component level.
-
Focus-275 -
Kyoritsu Testsystem Co., Ltd.
Focus275 is a tester for burn-in board.It can improve reliability of burn-in board by inspecting boards for burn-in test by Focus275 regularlyBoth short open test and component test can be done by sending electric signals for special socket contactor and edge part.
-
Acculogic, Inc.
An integral part of board test is the test fixture. Innovations in board technology may manifest themselves as challenges in test fixture design. Utilizing a creative & systematic design philosophy, Acculogic consistently delivers state of the art solutions for the most complex test interface problems.
-
TIQ1000 -
Rhesca Co., Ltd.
It is a device to measure repeated endurance such as limit bending test of board, endurance test of mounted board, endurance test of connector, etc. Continuity data and load data can be obtained during the cyclic endurance test. Conforms to JEITA ET-7407 "Environmental and durability test methods for mounted CSP/BGA packages".
-
ScanWorks Boundary-Scan Test -
ASSET InterTech, Inc.
The Boundary-Scan Test (BST) Development Software is one of the several configurations of the ScanWorks boundary-scan (JTAG) test and on-board programming environment. Test engineers can quickly develop interconnect tests and device-programming actions for use on first prototype board to accelerate the board bring-up process. Then tests can be exported for use in manufacturing and repair facilities.