Showing results: 3151 - 3165 of 3415 items found.
-
Panther 2K-CT -
Qmax Test Technologies Pvt. Ltd.
Panther 2K-CT is a versatile open\Short tester designed especially for reverse engineering application of tracing circuits of undocumented PCBA’s.Its innovative measurement technology helps tracing PCB tracks between components in a given circuit board. It can accommodate various types of clips\grabbers and connectors to access the device pins to trace the connectivity. Its user friendly software guides the user to place and move cluster of IC clips and probes to learn the connectivity and to generate netlist.
-
MS 1606 -
Meltronics Systemtech
The PowerBus is used to service printed circuit boards, instruments and systems, which has Micro controller / Microprocessor. The PowerBus has RS232 Communication for PC interface. The PowerBus connects to the UUT through the microprocessor / micro controller socket. The UUTs microprocessor / micro controller is removed from the UUT and it is replaced by the PowerBus. The Power Bus adapts microprocessor specific function as pin layouts, status / control function, interrupt handling, timing and memory and I / O addressability.
-
MODEL LCA-9PC -
Transducer Techniques, Inc
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
MODEL LCA-RTC -
Transducer Techniques, Inc
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
xiD -
XIMEA GmbH
*Quality components - Sony "EXview HAD CCD II" sensors delivering 2.8, 6.1, 9.1 and 12 Mpix*Fastest - Highest speed using full 4 TAP readout potential*Industry standard interface - Compliant with USB 3.0 SuperSpeed specification*Versatile mini camera - Subtle 60 x 60 x 39 mm, 320 grams (1)*Power - Lowest power consumption starting at 3 Watt, bus powered with USB3 cable*Cool - Minimal heat dissipation with passive COOLing*Compatibility - USB 3.0 support for Windows 7 and 10, macOS, Linux, ARM and 30 Libraries*Connectivity and Synchronization - Programmable opto-isolated input and output, 3 status LEDs*Bandwidth potential - 5Gb/s interface 400Mpix/s data throughput*Software interfaces - GenICam / GenTL and highly optimized xiAPI SDK for Image Processing*High grade - Quality class of sensors is combined with specially selected IR filters *Easy deployment - Range of accessories and widest hardware and software interoperability*Highly Customizable - Available in Board level and with Peltier TE Cooling
-
IFB-10003-INP -
Playing With Fusion Inc
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
IFB-10003-ANP -
Playing With Fusion Inc
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
IFB-10003-AWP -
Playing With Fusion Inc
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
IFB-10003-IWP -
Playing With Fusion Inc
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
Pasternack Enterprises, Inc.
Pasternack 75 Ohm BNC connector category contains many part numbers, most are RoHS and REACH compliant. 75 Ohm BNC connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Pasternack 75 Ohm BNC connectors are built to precise RF and microwave industry specifications. 75 Ohm BNC connector are available in male or female gender with 75 Ohm impedance. BNC 75 Ohm connectors are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These 75 Ohm BNC connector designs include clamp/solder, compression, crimp/solder or solder attachment methods. We offer 75 Ohm BNC connector with standard or high performance levels constructed with brass or stainless steel bodies. Like the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this 75 Ohm BNC connector group is in-stock. In addition to being in stock, these BNC 75 Ohm connectors will ship the same day as they are purchased.
-
Pasternack Enterprises, Inc.
75 Ohm Mini SMB connector category from Pasternack includes many part numbers, the majority are RoHS and REACH compliant. 75 Ohm Mini SMB connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our 75 Ohm Mini SMB connectors are built to precise microwave and RF industry specifications. Pasternack 75 Ohm Mini SMB connectors are built in jack or plug gender with 75 Ohm impedance. Mini-SMB 75 Ohm connector items are available in straight or right angle versions, as well as, bulkhead, 2 hole panel or mountless options. These 75 Ohm Mini SMB connector designs include crimp/solder or solder attachment methods. We offer 75 Ohm Mini-SMB connectors with standard or high performance levels manufactured with brass or stainless steel bodies. As with our other over 40,000 RF, microwave and millimeter wave products from Pasternack, this 75 Ohm mini SMB connector series is in-stock. Not only are these mini-SMB 75 Ohm connectors in stock, they also ship the same day as they are purchased.
-
Ironwood Electronics
Ironwood has the most comprehensive collection of BGA (Ball Grid Array) sockets that can be used for prototype application, silicon validation, system development, thermal characterization, burn-in application, functional production test, etc. BGA socket can be defined as an electromechanical device, which provides removable interface between IC package and system circuit board with minimal effect on signal integrity. BGA sockets for prototype applications, silicon validations, system development applications uses low cost elastomer contact technology.
-
TR7600 SII -
Test Research, Inc.
Featuring advanced automated 3D X-ray inspection of PCBAs, the TR7600 SII high speed scanning with multiple resolutions in a single program. Automatic Pass/Fail determination uses 2D + 3D images provided using 6-axis control and ultra-high-speed multiple angle cameras with automatic board warp compensation. TR7600 SII is ideal for inspection of fine pitch 01005 components, BGAs, PoPs, LGAs and other bottom termination components on both sides of the PCBA, including complex Pressfit connectors.
-
40-310-101 -
Pickering Interfaces Ltd.
The 40-310/320 Range of High Voltage Switching Modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications for the 40-310/320 series modules include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
HAB208 -
Axiomtek Co., Ltd.
The HAB208 has a PICMG 1.3 CPU card slot, a PCIe x 16 slot and a total of six 32bit/33MHz PCI slots. The onboard 24-pin ATX power connector and 8-pin connector for thermal detected board are featured. Furthermore, the backplane supports two onboard SATA ports (optional function). The HAB208 is perfect fit for AXIOMTEK's half-size CPU cards, the SHB210 and SHB211, which are built around the PICMG 1.3 form factor. We have enclosures, the AX60551 & AX60552, to house the backplane.
