Showing results: 3406 - 3415 of 3415 items found.
-
MS 1125 -
Meltronics Systemtech
Fuel Display Unit Test Bench is a compact table-top test bench with front panel controls, indications, built-in signal simulator and necessary power supply for testing the serviceability of Fuel Display Unit of Helicopter. FTB operates on 230 V AC and supplies 28 V DC power to FDU. FTB is housed in a metallic cabinet FTB interfaces with both 61 Pin connector and 6-pin socket mounted on the rear panel of FDU by means of the cable connected to the unit. FTB is fabricated utilizing off-the-shelf standard industrial/commercial components like rotary switches, toggle switches, press switches, test sockets, fuse holders, potentiometer etc. The Frequency generation circuit is integrated into FTB for the simulation of Fuel probe and flow rate signals. The frequency of the signal can be selected by means of a rotary switch Low amplitude sine wave signal is simulated for testing flow rates. Variable voltage DC power supply with a voltage range of 24 to 29 Volts is provided within FTB to power-up FDU. 5 V DC is provided for the operation of signal generating circuit (PIC Frequency Controller Board). An off-the-shelf Hand held battery operated Digital Multimeter (DMM) procured from the prominent manufacturer (FLUKE) is supplied with FTB for setting up and measurement of various parameters like Resistance, Voltage, Frequency etc.
-
Model 3541 -
Jinan Testing Equipment IE Corporation
The Model 3541 is designed for determination of fracture mechanics parameters such as JIC, KIC, R-curve, fatigue crack growth rate (da/dN), and testing to standards such as E1820, E399, E647, etc. These COD gages conform to the requirements of E1820 (the replacement for E813 and E1737) for JIC and R-curve determination. Special configurations are available to meet the requirements of ASTM E399 for fracture toughness (please consult the factory for these configurations). In addition, the modified groove design complies with E1820 tests where greater stability and accuracy results from the sharper groove root. Clip-on gages are used for a variety of fracture mechanics tests, including compact tension, arc shaped, disk shaped, bend specimens or other specimen geometries in compliance with ASTM and other standards organization’s test methods. Clip-on gages can be used directly on test specimens where the knife edges are integral with the test specimen or, alternately, with optional bolt-on knife edges mounted on the test specimen.The Model 3541 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Model 3560 -
Jinan Testing Equipment IE Corporation
This extensometer is ideally suited for testing anisotropic materials such as advanced composites as well as for general purpose tests like determining Poisson’s ratio. The Model 3560BIA uses a design unique to Epsilon, where the knife edges remain parallel during the displacement. This approach greatly reduces crosstalk between axes and allows use on round or flat specimens with equal ease. These extensometers are very easy to mount. Integral springs hold the unit on the test sample. The parallel multiple flexure design makes these units very durable.The Model 3560AVG reads axial strain only as a single averaged output. It may also be supplied with two independent outputs, one measurement from each side of the specimen. This set-up is most commonly required when an indication of specimen bending is desired. The second version, the Model 3560BIA, includes both the averaged axial strain and the transverse strain. Again, this may also be configured as dual independent axial readings, which results in a three channel extensometer.The Model 3560 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Model 3543 -
Jinan Testing Equipment IE Corporation
With over 15 years of proven reliability in the world’s most demanding testing environments, the Model 3543 extensometer is designed to survive in those applications where standard axial extensometers would not. Designed by Epsilon, the Model 3543 was created to survive specimen failure by separating into two halves, thus preventing permanent damage to the module body. During operation, the upper half of the extensometer pulls out of the main body. Tapered measuring beams activate strain gaged flexures within the unit. This unique design allows long measuring ranges, yet retains compatibility with electronics for strain gaged transducers. These models offer high accuracy and are light weight but rugged, with low operating force. They are tension only units.The units have hardened tool steel knife edges. Standard quick attach wires provided with the extensometer work on flat specimens up to 12 x 31 mm (0.5 x 1.25 inch) and on rounds up to 25 mm (1 inch) diameter. Optional quick attach kit wire forms are available for use on larger samples. See Model 3542L for long gauge lengths with smaller measuring ranges.The Model 3543 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
P200L or P300L -
The Micromanipulator Company
The Micromanipulator P300L 300mm semiautomatic probe station comes standard with features such as single-point ground and integrated thermal chuck plumbing. Built for reliability as well as precision, the P300L features leadscrew – leadnut stage and platen drives, a stainless steel platen with removable front wedge and high stability microscope bridge that supports all high resolution long-working distance microscopes.The P300L ‘s versatile controller supports USB and GPIB communications (configured with proper options). The stage X-Y and platen (Z) are motorized / programmable. Microscope motorized / programmable control is also an option. The system may be controlled via scripts and all popular parametric test analytical prober drivers. An indexing script with user GUI and a Labview VI is provided allowing use of the system right out of the box.Micromanipulator strives to ensure our semiautomatic systems are flexible so that applications like Magnetic sensitivity testing, Probe cards, mmW, Wafer & Board level testing. Once you have developed your testing plan we also have great relationships so we can move you into a fully automatic probe station if needed.Joystick control allows for easy and quick operation when programmability is not required. The joystick intuitively operates the station stage, platen, and microscope for systems so configured.The P300L may be configured with a local dry / shielded / dark environment “Top Hat” for low level or low temperature, frost free probing. Three temperature ranges are supported:Ambient (room temperature) to 300C0C to 300C-55C to 300CThe P300L is the station of choice for a high performance, full capability and cost-effective 300 mm semi-automatic probe station.
-
MIC-3398 -
Advantech Co. Ltd.
The MIC-3398 is a Low-Power 6U CompactPCI® CPU blade with best in class price/performance ratio tailored for applications that require a state of the art processor platform based on Intel® Architecture with full IO capability at an attractive cost point. The MIC-3398 supports Intel® Atom™ E3845 and Celeron N2930, J1900 SoC (system on a chip) family previously codenamed Bay trail with a maximum of quad-core 2.00 GHz processing performance. Intel® Atom™ technology provides significant increases in performance and energy efficiency by using the 22nm Intel® manufacturing process making it an ideal choice for control and workstation applications that require passive cooling with a power dissipation as low as 10W. Up to 8GB, dual channel 1333 MHz DDR3L memory with ECC support provide a high performance and robust memory interface for demanding applications. With built-in graphics based on Intel® HD Graphics Technology this blade offers a significant improvement in graphics performance compared to previous generation platforms. Support for an onboard 2.5” SATA-II drive as well as CFast SSDs adds comprehensive mass storage support. On the system side, the MIC-3398 supports 32-bit, 33MHz and 64-bit, 66MHz PCI bus interfaces to a CompactPCI backplane. A rich set of I/O interfaces such as DVI-D, USB3.0/2.0, Gigabit Ethernet and RS-232/422/485 ports round off the feature set. In addition to the single slot wide (4HP) board offering, a dual slot wide (8HP) version of the blade offers additional network connectivity by increasing Gigabit Ethernet port count from two to four.
-
Model 3565 -
Jinan Testing Equipment IE Corporation
The Model 3565 uses hard conical points to contact the bolt at the center of the head and at the bottom. It is fully adjustable for different length bolts ranging from 25 mm (1 inch) in length to 150 mm (6 inches) standard. Extension beams are available for longer bolts. The standard maximum measuring range is 1.25 mm (0.05 inches). Generally, on longer bolts this extensometer will be self-supported without requiring any centering marks or punch marks on the bolt. For shorter bolts these marks may be required. If the conical pins are sharp, marks are often not needed even on the shortest bolts.The extensometer has a zero adjustment screw to adjust the length between the contact pins. This is used to set the output voltage to zero, which corresponds to the correct starting position for the test. It also includes a breakaway lower arm. In the event a bolt should fail, the breakaway arm snaps free, helping to prevent damage to the extensometer. This is easily re-installed. In the event that bolt failures are likely during a test, it is recommended the user attach a cord around the upper part of the beam and tie the other end to the test frame to prevent the extensometer from falling. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 3565 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
MIC-6330 -
Advantech Co. Ltd.
Based on the Intel® Xeon® E3 Lv5 and Lv6 embedded platform, the MIC-6330 builds on the success of Advantech’s 6U VPX boards, and is the first 3U VPX product launched by Advantech. Together with the Intel® processor, the MIC-6330 offers intense computational ability in a very compact form factor. The MIC-6330 provides configurable connectivity (up to four ports) of PCI Express via the backplane to the highest performance mainstream peripherals and I/O cards, and vast I/O functions for extended interconnectivity and controllability. The MIC-6330 meets various computing needs, including vPro™ and workstation capabilities, by using the Intel® CM236/CM238 PCH. The MIC-6330 offers high storage capacity at up to SATA 6Gbps transfer speed. Four USB2.0 ports and one USB 3.0 port to the backplane fulfill requirements for extra I/O ports or storage, up to 5Gbps data rate. Four GbE ports (two ports configurable as SERDES) support system level IP connectivity, and the UART interfaces (RS-232/422/485 selectable) can be leveraged as an interface to legacy devices and consoles. Like Advantech’s 6U VPX products, the MIC-6330 supports multiple displays, and the maximum resolution of the MIC-6330 is 4K, empowered by the Intel® integrated graphics engine. The MIC-6330 also offers a High Definition Audio to the backplane interface for media demands. With the standard ruggedized convection cooled heatsink or the optional air-cooled heatsink, the MIC-6330 is tailored for harsh environmental applications and adaptable to various chassis designs. The industrial NAND Flash, and the soldered onboard DDR4 ECC memory chips are appropriate for a variety of vehicle applications for the maximum reliability. The MIC-6330 is sophisticated and suitable for various purposes. An onboard X8D XMC site with PCIE x8 gen.3 connectivity can host high speed offload or I/O mezzanines for project-specific applications. For applications that need the maximum expandability, the XMC interface can be modified to add another DisplayPort and the 2 more UART. The optional front I/O module facilitates the development and qualification process, and also enables the possibility of the front panel access.
-
CableEye M2Z, M3Z, M4 -
CAMI Research Inc. (CableEye®)
Fast ● Simple ● Precise Advanced wiring analyzer scans for continuity (opens, shorts), miswires, resistance, capacitance, components (resistors, diodes, LEDs, capacitors), insulation resistance, intermittent connections. For diagnostic and Pass/Fail Testing All CableEye® testers are suitable for production, fault diagnosis, QC (Quality Control), assembly, and prototyping of standard or custom cables. Each combines test, fault location, design, documentation, labeling, and database storage in one instrument. Tests can be performed on long cables (with or without connectors) or no cables (e.g. connectors, backplanes, PCBs, components). Standard Features & Benefits:
- USB certified, PC-based tester for a versatile, fast, robust system with long life-cycle.
- Multilingual, dynamic, graphic-rich display (netlist & wiring schematic) provides clarity and speeds diagnostics.
- 128 Test Points, expandable to 1024 providing flexibility as your product line changes.
- Real-time screening for intermittent connections for pinpointing elusive faults and improving quality.
- Automation scripting in a simple, intuitive language allowing non-programmers to reduce operator error by automating repetitive steps.
- Pop-Up Work Instructions. choose the exact amount of detail, imagery, language and automation you need to ensure your work instructions and tests are carried out flawlessly.
- Flexible tolerancing: optionally define as percentages or absolute terms, as well as asymmetrically (e.g. +0%/-10%) for improved yields.
- Barcode-tracking & archival data-logging to achieve error-proof test process and improved traceability & productivity.
- Print PASS/FAIL labels, test reports (with or without color wiring schematics/netlists) and log reports to satisfy ISO9000 reporting requirements.
- Compatible with laptop and touchscreen PCs for fieldwork and rack/off-bench mounting.
Includes: CB15C board set (Item 745C) for common computer and peripheral device cables; comprehensive PC software with Database of >200 standard cables; 2 yr Product Support Subscription comprising Warranty, free tech support, and free software upgrades.
Select Add-On Options: Hardware: 128-point Expansion Modules (attach to base); Environmental Sensor Software:
PinMap™ fixture editor,
Connector Designer™ connector editor, or
Autobuild™ guided assembly modules camiresearch.com |@CAMI_CableEye |+1.978.266.2655
-
CableEye HVX, HVX-21 -
CAMI Research Inc. (CableEye®)
Fast ● Simple ● Precise Advanced wiring analyzer scans for continuity (opens, shorts), miswires, resistance, capacitance, components (resistors, diodes, LEDs, capacitors) dielectric breakdown, insulation resistance, intermittent connections HVX (Item 829) 1500 Vdc, 1000 Vac HVX-21 (Item 829A) 2100 Vdc, 1200 Vac For diagnostic and Pass/Fail Testing — Permits expanded testing (compared to models in our low voltage product line) for insulation resistance (IRI) and dielectric breakdown (DWV). All CableEye testers are suitable for production, fault diagnosis, QC (Quality Control), assembly, and prototyping of standard or custom cables. Each combines test, fault location, design, documentation, labeling, and database storage in one instrument. Tests can be performed on long cables (with or without connectors) or no cables (e.g. connectors, backplanes, PCBs, components). Standard Features & Benefits:
- USB certified, PC-based tester for a versatile, fast, robust system with long life-cycle.
- Multilingual, dynamic, graphic-rich display (netlist & wiring schematic) provides clarity and speeds diagnostics.
- 128 Test Points, expandable to 1024 providing flexibility as your product line changes.
- User-selectable voltage to each connection group in the cable simplifies an otherwise complex process, accelerating testing.
- Programmable Ramp Up, Ramp Down, Dwell Time (same as Test Time), Trip Current, and Trip Delay (same as Soak Time) adds versatility.
- Current leakage detected during HV test phase provides a measure of insulation resistance up to 1 GΩ (HVX) and 5 GΩ (HVX-21) - any leakage current exceeding a preset limit reveals the presence of moisture, flux, or other contamination on exposed contacts.
- Real-time screening for intermittent connections for pinpointing elusive faults and improving quality.
- Automation scripting in a simple, intuitive language allowing non-programmers to reduce operator error by automating repetitive steps.
- Pop-Up Work Instructions. choose the exact amount of detail, imagery, language and automation you need to ensure your work instructions and tests are carried out flawlessly.
- Flexible tolerancing: optionally define as percentages or absolute terms, as well as asymmetrically (e.g. +0%/-10%) for improved yields.
- Barcode-tracking & archival data-logging to achieve error-proof test process and improved traceability & productivity.
- Print PASS/FAIL labels, test reports (with or without color wiring schematics/netlists) and log reports to satisfy ISO9000 reporting requirements.
- Compatible with laptop and touchscreen PCs for fieldwork and rack/off-bench mounting.
Includes: CB29 board set (Item 759) for bare wire connections; comprehensive PC software with Database of >200 standard cables; 2 yr Product Support Subscription comprising Warranty, free tech support, and free software upgrades.
Select Add-On Options: Hardware: 128-point Expansion Modules (attach to base); 4-Wire Kelvin Resistance Measurement, 1 mΩ at 1 A; Advanced Measurements; External Measurement Instrument Port (e.g. 10 GΩ Isolation at 100 V); Remote Control Connector for Deadman Switch; Environmental Sensor
Software: PinMap™ fixture editor,
Connector Designer™ connector editor, or
Autobuild™ guided assembly modules camiresearch.com |@CAMI_CableEye |+1.978.266.2655
