Filter Results By:
Products
Applications
Manufacturers
-
product
BARE BOARD TEST PROBES
Probe Technical DataMechanicalMINIMUM CENTERS: .100 (2.54)FULL TRAVEL: .160 (4.06)WORKING TRAVEL: .107 (2.72)OPERATING LIFE: 1,000,000 cyclesElectricalMAXIMUM CURRENT: 5 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current60 18 mOHMS mean63 60 mOHMS meanMaterials and FinishesPLUNGER: Heat treated beryllium copper60 24 Kt gold plated over nickel63 24 Kt gold plated over nickelBARREL: Nickel silver60 24 Kt gold plated ID and OD over nickel63 No FinishSPRING: Music Wire, 24 Kt gold platedover nickel
-
product
Barometric Pressure Transmitter
Comptus Barometric pressure sensors utilize an integrated silicon, absolute pressure sensor with internal temperature compensation. The sensor is mounted to the signal conditioner board. A 3/16 inch diameter tube may be attached to the sensor to provide remote pressure sensing. The output of the sensor is scaled to provide the desired output signal.
-
product
Basic CMC Extender for PrPMC, PMC, and PMC-X
4320
Basic CMC Extender for PrPMC, PMC, and PMC-X. The Basic Common Mezzanine Card (CMC) extender provides a means to extend IEEE 1386 boards for signal accessibility. PrPMC (VITA 32), PMC (IEEE 1386.1), PMC-X (VITA 39) and any other CMC-derived board is supported.
-
product
BASIC-programmable IoT Board
EM1001
Our flagship BASIC/C-programmable IoT board. Ethernet, as well as optional Wi-Fi and GPRS connectivity. Four serial ports supporting full-/half-duplex RS232, Wiegand, and clock/data modes.
-
product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Battery Pack PCM Test Equipment
Xiamen WinAck Battery Technology Co., Ltd.
This battery PCM/PCB test equipment is suitable for the basic parameter test and protection function test of lithium battery pack protection board of mobile phone & digital products; it is also used for downloading, comparing and PCB calibration of battery management.
-
product
"Bay Trail" Atom Processor
XMC-120
Curtiss-Wright Defense Solutions
The XMC-120 from Curtiss-Wright Defense Solutions is a small form factor and low power x86 single board computer (SBC). Designed for space-constrained size, weight and power (SWaP)- sensitive programs, the XMC-120 offers quad-core x86 processing performance with ultra low power and small sized footprint.
-
product
BGA Socket And BGA Adapter Systems
Mill-Max's BGA Socket/Adapter Systems are used for both socketing BGA devices and interconnecting circuit boards. Systems are available to fit 1mm, .050" and .8mm grid footprints.
-
product
Bi-Directional Level Translator
IFB-10001
Easily connect Arduino or other 5V microcontrollers to ~3.3V sensors. Based on the TI TXB0108 auto-sensing, bi-directional level translator, this module provides access to all 8 channels of the TXB0108 and has a built-in 300mA LDO with 200mV max dropout voltage at full load. Regulated 3.3V output allows this single board to both interface withandpower 3.3V sensors. An important feature of this module is the ability to operate SPI and other digital lines (not including I2C) at high-speed, whereas the 'NXP level shifter' maxes out at 400kHz and resistor dividers fail much earlier. The TXB0108, integrated with the LP3981 LDO, provide a fast, reliable solution to mismatched interface voltages that exceeds the performance of other solutions.
-
product
Big Easy Driver
The Big Easy Driver, designed by Brian Schmalz, is a stepper motor driver board for bi-polar stepper motors up to a max 2A/phase. It is based on the Allegro A4988 stepper driver chip. It's the next version of the popular Easy Driver board.
-
product
Bit Synchronizers, Decoms, and DACs
Lumistar offers bit synchronizer boards compatible with the PCI bus, VME bus, and daughter-boards for use with various Lumistar products.
-
product
Bit Waveform Digitizer Board
ATS9373
ATS9373 is a 12 bit waveform digitizer board that can sample one analog input at rates up to 4 GS/s or two inputs at 2 GS/s. With on-FPGA FFT signal processing and data throughput as fast as 6.8 GB/s (6800 MB/s), ATS9373 is an ideal solution for many applications, including next generation OCT, radar, ultrasonics, spectrometry and RF signal recording.
-
product
BMS Transformers
In large battery pack applications with daisy chain connections, the number of cells connected in series is very high, and the large voltage differences demand component-to-component isolation. The serial communication links between boards need to be isolated by transformer coupling circuits instead of capacitor coupling.
-
product
Board
Arduino MKR1000 WIFI
Monacor International GmbH & Co. KG
Arduino MKR1000 is a powerful board that combines the functionality of the Zero and the Wi-Fi Shield. It is the ideal solution for makers wanting to design IoT projects with minimal previous experience in networking.
-
product
Board Connectors
Advanced Interconnections Corp.
High density designs maximize board spaceScrew-machined terminals for superior performanceSurface mount, spring pin, and thru-hole solutions
-
product
Board Repair Assistant & Quality Management System
QUAD
QUAD (QUality ADvisor) is a flexible modular Quality Management system built around a centralized and open architecture database, providing traceability for any PCB electronic production data. QUAD covers all quality aspects of PCB assembly, sub-assembly and system build, allowing you to manage the quality data flow from product realization to product retirement.
-
product
Board Test
The Horizontal/Vertical Signal Integrity Manual Work Station allows for multiple size circuit board configurations.
-
product
Breakout Boards
Breakout your Raspberry Pis and Arduinos with this broad selection of versatile breakout boards! Engineered to help you realize your robotics, GPS and altitude sensing projects as well as servo and touch screen interfacing, you''ll find many uses for these high-quality boards, most of which are manufactured in house at Adafruit!
-
product
Breakout Boards
Micro D
Micro D Breakout Boards are also open designs providing signal access for the popular MicroD series of connectors. Breakout boards incorporate one male and one female connectors.Micro D Type: 9, 15, 21, 25, 31, 37, 51 and 100 positions
-
product
Breakout Boards
D Series Boards
D Series Breakout Boards are open designs that provide signal access when troubleshooting. Signal connections are accomplished by inserting or removing Mini-Jumper plugs. All normal and high density D type connectors are available. Current carry capability is from 2.25A to 5.3A. Normal Density D Type: 9, 15, 25, 37 and 50 positionsHigh Density D Type: 15, 26, 44, 62, 78 and 104 positions
-
product
Breakout Box
FV-EXT
The handy FiberVision devices FV-EXT1 and FV-EXT2 are designed for the easy integration of FiberVision and Vision Component (VC) smart cameras into your production environment.Central interface for all supply- and communication-cables (switch board)Remote control for all VC based smart cameras such as Caminax or PictorTest of digital camera I/Os and the production environment
-
product
Breakout Boxes
D Series
The D Series Breakout Boxes incorporate a printed circuit board for all connectivity. D Series Breakout Boxes use a color coding scheme as an aid. The Red jacks connect to the Red TP Side connector with pin contacts and the Black jacks connect to the Black TP Side connector with socket contacts.
-
product
Broadband Amplified Noise Modules
NC2000/4000 Series
The NC2000 Series amplified noise modules are an excellent choice for high-level noise modules mounted on a circuit board. The NC2000 Series modules are housed in 24, or14-pin dual-inline packages. The NC4000 series modules are housed in a 40-pin module that cover similar noise bands to the NC2000, but have higher crest factor, and 60 dB of TTL controlled attenuation.
-
product
Burn-In Boards
Meets burn-in requirements, including extreme temperatures or continual handling. 2 or more layers of polyimide. 200 C maximum temperature. Gold-plated connectors.
-
product
Bus Level Timing Cards
Brandywine offers the widest range of timing plug-in card form factors in the industry from the PCI timing cards to PMC to VME cards. With the largest variety of options including standards like IRIG B, 1PPS, Have Quick, and GPS you can customize your timing card to fit your needs. All of Brandywine's board level timing cards are made in our factory in El Paso, Texas which ensures quick delivery and quantity ranges from small to large for a low price.
-
product
Camera Interface Boards and Adapters
Active Silicon offers camera interface boards for autofocus-zoom block cameras and adapters for host-end acquisition and video format conversion. The camera interface converter boards for Tamron AF-zoom cameras, Sony FCB block cameras, Harrier AF-zoom cameras and others, take data from the proprietary block camera interface and convert into industry standard formats such as 3G-SDI / HD-SDI, USB 3.0, HDMI and IP.
-
product
CamTrac Z-Axis Test Fixture Kits
CT Serie
The CT Series Mechanical Kits, utilizing the patented CAM mechanism1, offset the same precision linear motion. The 'Z' axis motion is ideal for a larger point count mechanical test applications.The CT Series features a hinged 3/8" FR4 probe board, tooling holes for precision alignment, removable sides, precision shafts and cam slide block assemblies, and a pan latch assembly.
