Showing results: 361 - 375 of 435 items found.
-
PFT-500 -
Jinan Testing Equipment IE Corporation
PFT-500 hydraulic pulse fatigue testing machine is mainly applicableto large size parts such as bridges, trusses, automotive chassis, front and rear axels, locomotive frames, chassis and various concrete structures for static compression test and dynamic unidirectional pulse fatigue tests. The Fatigue Testing System for Rail has significant characteristics of reliable design, simple operation, energy conservation, and low operation cost etc.
-
Pacific Instruments, Inc.
Series 6800 for portable applications is a ready-to-run, high performance measurement system that is DC powered for mobile applications. All connections are front mounted for easy installation in tight places or on the go. 6800 systems come equipped with a conditioner, amplifier, filter and digitizer. Each channel has a front mounted connector specific to a measurement type: RJ-45 for 8-wire bridge transducers or BNC for voltage or ICP/IEPE inputs.
-
PeakTech Prüf- und Messtechnik GmbH
Is a thermal imaging camera with a thermal resolution of 160x120 thermal image points with a high-quality sensor, which makes even the smallest temperature differences visible. All thermal images can be opened and evaluated using the enclosed software, with subsequent changes, e.g. can be done on the pallet selection. Use this new development to find thermal bridges in thermography, leaks in systems and pipe systems or track heating pipes in walls and floors.
-
Model EP400 -
Gopal Electronics
Digital Epstein Tester EP-400 is designed to measure AC magnetic properties of flat rolled magnetic materials at high frequency by using Watt-meter, Ammeter, Voltmeter and Source. Epstein bridge test method is a fundamental method for evaluating the magnetic performance of flat-rolled magnetic materials in either sheared or stress relief annealed condition. This test method is suitable for design, specification acceptance, service evaluation, and research and development.
-
SY040 -
Synectic Electronics
SY040 Load Cell Simulator High Precision Instrumentation generates a mV/V signal. A great high precision simulator to use for either test, calibrating and also troubleshoot strain gauge applications. A wide range of bridge resistances can also be simulated including 350, 700, 1000, 1400 & 2000 ohm. The range of preset switch positions include 0, 0.2, 0.4, 0.6, 0.8, 1.0, 2.0, 3.0, 3.5, 4.0 & 4.5 mV/V. The option of very fine adjustments is also possible as this instrument has a knob for continuously variable adjustments between the preset ranges. Users can make a connection via 4mm banana connectors mounted on top of the case.
-
LCF-2330 -
Jewell Instruments LLC
The LCF-2330 inclinometer series now includes a 4-20mA output signal option for applications that require long cable runs. This dual axis tilt sensor is fluid damped to minimize noise and vibration interference while also offering a sharp 1 µradian resolution. An internal temperature sensor is available and dual supply, ± 5 Vdc output is an option. The LCF-2330 is an excellent solution for rugged applications such as radar & antenna leveling, weapons platform leveling, barge and offshore platform control, deviation surveys, 2-axis machine tool leveling, bridge structural monitoring, submersible control feedback, offshore platform stability and manufacturing process equipment for the aerospace industry.
-
785921-01 -
NI
Up to 480 GB SSD Expansion Module for CompactRIO - The cRIO-9803 provides a bus-powered USB SATA bridge to a full-length mSATA solid-state drive (SSD). This module uses a USB Type C connector with integrated cable retention. It also works with devices that feature other types of … USB connectors, such as CompactRIO Single-Board Controllers, Industrial Controllers, and PXI Controllers. The cRIO-9803 is available in 64 GB SLC for high endurance in rugged environments, in 480 GB MLC for high-capacity data storage, and for use with a customer-supplied SSD. Additionally, the cRIO-9803 features the same rugged shock and vibration ratings as other CompactRIO modules and can be mechanically connected to a controller for integration using mounting accessories.
-
785920-01 -
NI
Up to 480 GB SSD Expansion Module for CompactRIO - The cRIO-9803 provides a bus-powered USB SATA bridge to a full-length mSATA solid-state drive (SSD). This module uses a USB Type C connector with integrated cable retention. It also works with devices that feature other types of USB connectors, such as CompactRIO Single-Board Controllers, Industrial Controllers, and PXI Controllers. The cRIO-9803 is available in 64 GB SLC for high endurance in rugged environments, in 480 GB MLC for high-capacity data storage, and for use with a customer-supplied SSD. Additionally, the cRIO-9803 features the same rugged shock and vibration ratings as other CompactRIO modules and can be mechanically connected to a controller for integration using mounting accessories.
-
786677-01 -
NI
Up to 480 GB SSD Expansion Module for CompactRIO - The cRIO-9803 provides a bus-powered USB SATA bridge to a full-length mSATA solid-state drive (SSD). This module uses a USB Type C connector with integrated cable retention. It also works with devices that feature other types of USB connectors, such as CompactRIO Single-Board Controllers, Industrial Controllers, and PXI Controllers. The cRIO-9803 is available in 64 GB SLC for high endurance in rugged environments, in 480 GB MLC for high-capacity data storage, and for use with a customer-supplied SSD. Additionally, the cRIO-9803 features the same rugged shock and vibration ratings as other CompactRIO modules and can be mechanically connected to a controller for integration using mounting accessories.
-
WMA-IB-LN -
Falco Systems
The WMA-IB-LN can be used to double the output voltage of two high voltage amplifiers by driving them in bridge mode, or as high impedance input buffer while maintaining precision and ultra-low noise. The WMA-IB-LN model has been designed specifically for the Falco Systems WMA-200 high voltage amplifier. Two WMA-200 amplifiers combined with one WMA-IB-LN provide unprecedented noise performance and output voltage range.
-
Hubbell Power Systems Inc
The purpose of the Energized Cable Sensor is to allow the lineman to readily determine whether a URD cable is energized. The sensor consists of an amplifier which is designed to give a meter reading when the small AC voltage between the semi-conductive sheath and the concentric neutral of the energized URD cable is applied to the test probe. The amplifier is housed in a rugged phenolic case. Sensor may be used to check for energized condition on concentric-neutral cable below an elbow without test points. At cable mid-span (left), hose clamps bridge all strands of concentric neutral at the test location. Sensor’s neutral lead clips to one of the hose clamps. Tip on probe lead contacts only semi-conductive cable sheath to test for voltage presence.
-
Qualitest International Inc.
This category comprises the range of instruments that use sound or stress waves in order to determine the properties of concrete and other materials non-destructively. The first and most widely used System is our V-Meter, which utilizes the ultrasonic pulse velocity method for evaluating construction materials in the field. Transducers are available for a variety of frequencies from 24 KHz to 500 KHz. This unit has also been modified to suit the special needs of ceramics users and can be found as the Ultrapulse. The PIES, our revolutionary Portable Impact-Echo System, is an advanced instrument for non-destructive detection of flaws and defects in a variety of civil infrastructures ranging from bridges, parking structures and buildings to dams, piles, tunnels, tanks and marine structures.
-
28000 -
Precision Filters, Inc.
The Precision 28000 Signal Conditioning System makes it easy to manage a test with up to 256 channels of fully programmable transducer conditioning. Choose a mix of bridge, charge, IEPE w/TEDS, voltage (filter amplifier), strain, thermocouple, RTD/potentiometer, frequency, or other transducers. Self-tests traceable to NIST. 4, 8 and 16-slot rugged and transportable mainframes feature integrated cooling. Customize the 28000 for high-speed transient applications, static applications, or a combination of both.
-
WMA-IB-HS -
Falco Systems
The WMA-IB-HS can be used to double the output voltage of two high voltage amplifiers by driving them in bridge mode, or as high impedance input buffer while maintaining precision, high speed and low noise. Because of its high bandwidth, the WMA-IB-HS model is ideal for the Falco Systems WMA-100 or WMA-300 amplifiers. It can also be used with all other Falco Systems HV amplifiers, or even with high voltage amplifiers of another brand.
-
1830A -
TEGAM Inc.
Thermistor based RF power sensors are universally recognized as the most accurate means to measure and transfer RF power. Compatible with thermistor power sensors from: Agilent (HP), TEGAM, Weinschel, Hughes, General Microwave, Millitech. Supports 100 and 200 thermistors. Integrates bridge balancer and power meter into one package. Four digit calibration factor resolution. Full remote programmability. Heater control for ovenized sensors. LXI Compliant.
