Showing results: 406 - 420 of 425 items found.
-
XWRM-10 -
The Motwane Manufacturing Company
The Motwane make XWRM-10 is a dual channel 10A rated, Transformer Winding Resistance Meter designed and developed aftere xtensive research on challenges and requirements of testing of various Transformer winding resistance. The instrument has One Current channel and two Resistance Channels. The instrument provides a large open circuit voltage of 42Volts, for fast charging of the highly inductive windings of transformers, to provide stable resistance values in minimum time. The XWRM-10 is intended to replace complex bridge set up with a single compact instrumentThe XWRM-10 is based on 4-wire measurement methodto measure low resistance accurately. The instrument iswell protected against inductive kickbacks offered by theinductive windings and gives stable reading on varioustypes of transformers.
-
MODEL TMO-2A -
Transducer Techniques, Inc
The TMO-2A Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The unit provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Zero to full scale output is specified at 4-20 mA. The TMO-2A provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
WISER 8000 -
TECAT Performance Systems, LLC
The TECAT WISER Model 8000 dual strain measurement and monitoring system is a wireless data acquisition system for measuring two external strain channels at high data rates up to 8kHz. The small, light, power-efficient, and non-invasive design enables strain measurements in a wide range of applications. With dual external sensor inputs two Micro-Measurements strain gauge bridges can be measured by a single system, for example to measure both thrust and torque loads simultaneously.The Model 8000 has a long range data transmission of >1,000 meters with up to +/- 0.025% FSR sensitivity for remote measurements. After initial setup using the WISER software interface, the system can be wired directly to your DAQ system, for seamless data collection.
-
PCE Instruments
A vibration meter is used in manufacturing for machine condition monitoring, product testing and quality assurance. Many machine maintenance technicians use vibration meter devices in tandem with sound level meters to analyze frequency. A vibration meter also can be used in civil engineering to measure the vibration of structures such as buildings, roads and bridges. In addition, specialized vibration meter devices can be used to measure the vibration of the human body. Any vibration meter will measure one or more of the following parameters: vibration acceleration, vibration velocity (speed) and / or vibration displacement.A vibration meter is typically a portable device with a memory for storing measurements. Most vibration meter models feature a built-in data logger for collecting and recording vibration measurement data over time. In this way, vibration measurement data can be acquired with great precision.
-
DTX 5000 Series -
R.C. Electronics, Inc.
The DTX-5000 Signal Conditioner Series provides up to 64 channels of state-of-the-art signal processing in a compact (5U) chassis. Using hybrid mixed-signal technology, high-performance analog circuitry is combined with Digital Signal Processing to give gain accuracy performance previously available only in larger customized modules. A simple-to-use graphical user interface running under the Windows 2000 operating system allows for ease of setup and either local or remote operation as a network-based instrument node. The suite of conditioner modules include a strain amplifier with internal bridge completion, a general-purpose instrumentation amplifier with selectable AC or DC coupling, a linearized thermocouple amplifier with cold-junction compensation, a frequency-to-voltage converter with dual inputs for direction sensing, and an ICP accelerometer amplifier with constant-current excitation.
-
Procter & Chester Measurements Ltd
Pressure: Measures gas or liquid pressure. Pressure is an expression of the force required to stop a fluid from expanding. The transducer generates a signal from the pressure imposed upon it. Torque: Measures the torque (or twisting motion) on a static or rotating system. The static torque element has little movement and therefore more economic to manufacture and purchase. Rotary or dynamic torque is more complicated as the signal needs to be transferred using slip rings, wireless telemetry or rotary transformers/inductance technology so that the strain gauged shaft can continuously rotate. Displacement: Measures distance. The displacement transducers that PCM offer are slightly different to standard units. They have a strain gauge/wheatstone bridge. The benefit here is that if the customer has existing electronics that uses strain gauge/load cell technology, they can use them with these sensors.
-
MODEL TMO-2 -
Transducer Techniques, Inc
The TMO-2 Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The units provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Full scale output is specified at plus or minus 10 VDC. The TMO-2 provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability for applications such as weighing scales. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
eBOX660-872-FL -
Axiomtek Co., Ltd.
A high-performance fanless embedded system with 3rd Generation Intel® Core™ processor (Ivy Bridge), the eBOX660-872-FL, is presented by Axiomtek earnestly. It incorporates the 3rd Generation Intel® Core™ processor (i7/ i5/ i3) or Intel® Celeron® processor with Intel® HM76 Express chipset, propelling computing with better processing. With the great graphics computing capability and dual view support, this fanless embedded box computer is especially suited for automatic optical inspection, digital signage (DS), digital surveillance, gaming, automation control and POS/Kiosk. In addition, this application-ready compact rugged platform also targets for nearly any field of industrial embedded applications like embedded controller, factory automation and more fields.
-
785641-01 -
NI
8-Channel Strain/Bridge Input Device for FieldDAQ - The FD-11637 can measure eight channels and has built-in bridge completion and voltage excitation to support for quarter-, half-, and full-bridge sensors. It also features anti-alias filtering, offset nulling, and shunt calibration to reduce the effect of noise and improve measurement accuracy. The FD-11637 has an ingress protection rating up to IP67 (dust- and water-resistant), can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 grm vibration. The FD-11637 incorporates Time Sensitive Networking (TSN) and features an integrated network switch and built-in power circuitry for simple daisy chaining. You program the FD-11637 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. The FD-11637 is ideal for test cell and outdoor environments.
-
VPX3010 -
ADLINK Technology Inc.
The VPX3010 Series is a 3U VPX processor blade featuring the Intel® Xeon® Processor D-1500 SoC with up to 12 cores. The VPX3010 provides up to 16GB DDR4-2133 dual channel ECC memory soldered onboard, one PCI Express x8 Gen3 XMC expansion slot with VITA 46.9 rear IO, and onboard soldered 32GB SLC SATA solid state drive. Rear I/O via P1 and P2 includes 2x 10GBASE-KX4, 2x 1000BASE-T (or one 1000BASE-T and two 1000BASE-BX by BOM option), 2x SATA 6 Gb/s, 1x USB 2.0, 2x USB 3.0, 6x GPIO, VGA, 1x RS-232, 1x RS-232/422, and up to PCIe x16 Gen3 supporting non-transparent bridge for peer-to-peer communication (dependent on BOM option).
-
ERAVANT
A universal heatsink, which is designed and fabricated for Eravant's active device applications with up to 15-watt power dissipation. The heatsink consists of the main heatsink body, a DC fan and a heat spreader. The heat spreader is also known as adapter, which is used to bridge the mounting gap between the heat sink main body and the to-be-heat-sunk devices, such as power amplifier, frequency active multiplier, oscillator, transmitter and transceiver due to various mounting hole locations. The heat spreader offers various mounting patterns to accommodate more than 15 product models. This heatsink is not only designed for Eravant's standard products and Uni-Guide™ featured products, but also for many industrial standard microwave and millimeter wave products offered by other manufacturers. Other heatsinks with different power dissipation capacities are offered under different model numbers.
-
PCI113 -
Vadatech Inc
PCI113 is VadaTech second generation PCIe expansion module. The PCI113 is a high-speed 20Gbps bridge from the host PCIe bus to VadaTech’s carrier and Rear Transition Module (RTM) products such as the ATC104/114/118/117/119, ART114, μTCA chassis, etc. The different carriers host different I/O modules such as PMC/PrPMC, AMC, PCI-X and PCIe edge modules. This concept allows any of the available I/O modules in these standard form factors to be integrated quickly and easily into an AdvancedTCA or μTCA subsystem. The PCI113 allows expansion among multiple μTCA chassis or expansion into other chassis that are not ATCA or μTCA based.The PCI113 is a single module PCIE based on the PCISIG specification. The PCI113 provides a PCIe x4 link infiber/copper via front panel QSFP. The dual front I/O allows expansion into two separate systems independently. The upstream port must not have spread spectrum PCIe clock enabled.
-
CM22303 -
LinkedHope Intelligent Technologies Co.,Ltd.
CM22303 uses Intel® 7th generation Kaby Lake-Y platform and Core M Ultra low-power SoC processors, and integrates the full functions of CPU, GPU and South/North Bridge on a single chip. The processor provides powerful computing and display performance with dual-core and four threads configuration. Its turbo frequency can boost up to 3.6 GHz and the display output resolution can be up to 4K. CM22303 has an amazing thermal design power consumption of only 4.5W (TDP) and can be used for a variety of high-performance fanless designs. SPI BIOS is designed on board to support dual-channel low voltage on board memory (up to 16GB), Gigabit Ethernet, TPM module and other functions. With high-performance and low power consumption, it can be widely used in the field of low power embedded systems. Meanwhile, CM22303 adopts COM Express standard and is compatible with Type10 pin out definition, and also provides rich peripheral interfaces such as USB3.0/2.0, PCIe, SATA, HD Audio etc.
-
Pacific Instruments, Inc.
Series 6000 analog I/O modules condition, amplify, filter and digitize signals from virtually any transducer. All modules have conditioning & amplifier per channel and nearly all modules allow for setting bridge completion, shunt calibration, transducer power, gain, etc. individually per channel. Following the conditioning/amplifier stage, multi-pole Bessel or Butterworth analog filters are provided on each channel and can be set or bypassed individually by program control. A number of the modules include a high level analog output providing a conditioned/filtered output to a redundant, external A/D system. A 16-Bit Successive Approximation A/D follows the analog filter stage. Some modules use a single A/D with sample and hold while others have an A/D per channel. Sample rates are programmable per channel to easily accommodate mixing high and low speed measurements into a single data stream. Programmable hardware based warnings and alarms are included in the channel-by-channel architecture and are detected by digital output modules in the system, providing an ultra-low latency control capability directly from the data acquisition system.
-
Sinowon Innovation Metrology Manufacture Ltd.
Moving bridge structure, measured workpiece is fixed;◆ Four-axis CNC fully auto close loop control, auto measurement;◆ “00” grade “JINANQING”marble base and pillar, stable and reliable;◆ Imported open type linear scale, resolution is 0.1um, high accuracy, great stability;◆ Imported P grade linear guide, precision grinding ball screw and AC servo motor, ensure accuracy stability of system position;◆ Imported high definition color industry camera, ensure clear observation and stable measurement requirement;◆ 6.5X continue auto zoom lens, precision auto zoom, only need to make pixel calibration once time;◆ Programmable 5-ring 8-division LED surface illumination, contour parallel LED illumination, can realize 256 grade brightness adjustment intelligently;◆ Equipped with imported touch probe, realize 3D measurement;◆ With proprietary fully auto measuring software iMeasuring 4.2, powerful function, simple operation;◆ Optional laser probe, it can also be customized according to customer request;◆ Optional FexQMS Measuring Data Analysis and Real-time monitoring software which enhance program control and reduce material
