Filter Results By:
Products
Applications
Manufacturers
Bus Interfaces
Enable bus interoperability.
See Also: Interfaces, Serial Interfaces, Parallel Interface, UI, MIPI, Interface Adapters, Bus
- Pickering Interfaces Inc.
product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 8 Channel
40-201-008
This high bandwidth differential PXI fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
product
Bus Interface
IP-1553
MIL-STD-1553 is a versatile standardized bus interface. MIL-STD-1553 is robust featuring Manchester encoding and enough voltage swing to provide excellent noise immunity and reasonable throughput rates.
-
product
PCI Bus Interface
PCI-6713-4IP
PCI Bus Interface 3.3 / 5 Volt via PLX 9056 33/66MHz High Performance Floating-Point DSP Up to 300MHz system clock. Up to 32Mbytes of SDRAM 4.0 Mbit flash memory for bootstrap program.
-
product
PXI Bus Interfaces
PXI Bus Expanders and PXI Interface Cards for both PXI and PXI Express interfaces.
-
product
Standardized Bus Interface
IP-429-II
Connect to your Avionics with IP-429. Pick 2,4,6,or 8 ARINC 429 compatible receivers and 1, 2, 3, or 4 transmitters. Transorb protected IO. Software programmable transmit rates [100K or 12.5K]. Time Tag on received data. IndustryPack campatible with 8 or 32 Mhz. bus operation.
-
product
ARINC 429 Bus Interfaces
AIM’s > ARINC 429 test, simulation, monitoring and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with multiple processors for real time bus protocol and application support, massive memory and IRIG-B time code encoder/decoder functions are standard. The latest versions also support avionics discrete I/O.
-
product
PCI BUS Interface Card
PCI301
MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester PCI BUS Interface Card - The PCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.
-
product
CPCI BUS Interface Card
Cpci301 MIL-STD-1553
MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator / Analyzer / Tester CPCI BUS Interface Card - The CPCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.
-
product
ECU & Bus Interface Modules
ES500
ETAS makes the entire software and hardware range available from program development to the calibration of your ECUs. You can use the ETAS tools to address all ECUs that satisfy the ASAM standard. By using these standardized interfaces, our tools are not limited to the ECUs of any particular manufacturer.
-
product
Pressure Transducers with CAN Bus Interface
P66
The Validyne model P66 is a digital differential pressure transmitter designed for industrial pressure measurement applications. The on-board microprocessor provides high accuracy and improved stability in changing thermal environments. Communication via CAN Bus provides remote zero and span adjustment as well as digital pressure readings in engineering units or pressure counts.
-
product
GPIB General Purpose Interface Bus
The design of the GPIB control card is fully compatible with the IEEE 488.1 and IEEE 488.2 standards, using the PCI interface, supporting the Plug & Play specification, and supporting Windows 95/98/Me /NT4.0/ 2000 /XP/7 Operating system, driver function library includes Windows development software tools such as Visual C++, Borland C++ Builder, Labwindows, Visual Basic, Delphi and Labview. This GPIB-supported library provides an NI-like command control syntax format, which is convenient for users to develop and transfer applications smoothly. This interface card also provides a conversational window GPIB interface program, which is convenient for users to directly control the instrument without writing a program.
-
product
Shuttle Bus VMC Intelligent Interface Card
IIB-SB-VME
The Shuttle Bus VME is an intelligent interface card providing all Launch Data Bus, Ground Data Bus, andMultiplex De-Multiplex Multiple Remote Terminal capability to the Shuttle Bus, as required by NASA specification84K01203 (Hardware Specification, Launch Data Bus (LDB) and Ground Data Bus (GDB) Interface Board).In summary, this card provides all features and functions required to meet the above specification, in a VMEplatform, with Simplex & Half-Duplex modes provided. Specific operational modes provided include LDB_BCT,LDB_MRT, GDB_BCT, GDB_MRT, BUS_MON, MDM_MRT, Primitive and Calibration modes.
-
product
Shuttle Bus cPCI Intelligent Interface Card
IIB-SB-CPCI
The Shuttle Bus cPCI is an intelligent interface card providing all Launch Data Bus, Ground Data Bus, and Multiplex De-Multiplex Multiple Remote Terminal capability to the Shuttle Bus, as required by NASA specification 84K01203 (Hardware Specification, Launch Data Bus (LDB) and Ground Data Bus (GDB) Interface Board).In summary, this card provides all features and functions required to meet the above specification, in a cPCI platform, with Simplex & Half-Duplex modes provided. Specific operational modes provided include for LDB_BCT, LDB_MRT, GDB_BCT, GDB_MRT, BUS_MON, MDM_MRT, Primitive and Calibration modes.
-
product
Shuttle Bus PMC Intelligent Interface Card
IIB-SB-PMC
The Shuttle Bus PMC is an intelligent interface card providing all Launch Data Bus, Ground Data Bus, Multiplex De-Multiplex Multiple Remote Terminal, and Ground Data Bus (GDB)capability to the Shuttle Bus, together with a Pulse Code Modulation Mode. This card provides all features and functions required in a PMC platform, withSimplex & Half-Duplex modes provided. Specific operational modes provided include for LDB_BCT, LDB_MRT, GDB_BCT, GDB_MRT, BUS_MON, MDM_MRT, Primitive and Calibration modes.
-
product
Low-profile High-Performance IEEE488 GPIB Interface for PCIe Bus
LPCIe-3488A
The IEEE-488 standard, also known as GPIB, is a bus interface that connects instruments with a computer to form an ATE system. Today, GPIB is still the most popular interface between computer and instruments. ADLINK"s USB-3488A, LPCI-3488A and LPCIe-3488A controller interface cards are fully compatible with the IEEE-488.2 instrumentation control and communication standard and are capable of controlling up to 14 stand-alone instruments via IEEE-488 cables. The USB-3488A, LPCI-3488A and LPCIe-3488A are designed to meet the requirements of high performance and maximum programming portability.
-
product
Low-Profile High-Performance IEEE488 GPIB Interface for PCI Bus
LPCI-3488A
ADLINK LPCI-3488A GPIB controller interface card, fully compatible with the IEEE 488 instrumentation control and communication standard, is capable of controlling up to 14 stand-alone instruments via IEEE 488 cables. It is designed to meet the requirements for high performance and maximum programming portability. The built-in 2KB FIFO and a block transfer mode provide up to 1.5 MB/s GPIB transfer rate. With the APIs that are compatible with NI-488.2* and VISA support, the LPCI-3488A provides the greatest compatibility with your existing applications and instrument drivers. (* NI-488.2 mentioned here is the trademarks and properties of National Instruments Corporation.)
-
product
GPIB to I2C and 8-Bit Data Bus Interface
Model 4802
ICS's GPIB to I2C Interface Board is an IEEE-488.2 GPIB and HP-IB compatible interface for I2c and SMB devices.
-
product
Simulator / Analyzer / Tester PCI BUS Interface Card
CIC301 - MIL-STD-1553
The CIC301 is a full-featured, high performance, Dual Redundant MIL-STD-1553 A/B serial bus Simulator Analyzer Tester designed as a plug in card for PCI backplane. The CIC301 includes full error injection and can operate in independent or simultaneous mode as a Bus Controller, multiple simulated Remote Terminals and full/selective Monitor. Its data structure can be changed on the fly without interrupting the processor for real time operation. The active monitor stores, time tag and annotates bus traffic with the message type and any detected errors. Stored words are annotated with a break down of the word error.
-
product
3U Format CompactPCI (CPCI) Bus IP Carrier
CPCI-SIP-2
The CPCI-SIP is a 3U format CompactPCI (CPCI) bus IP carrier. The CPCI-SIP-2 provides mechanical support and the electrical interfaces for two single width IP modules, or a double width IP module. Multiple CPCI-SIP-2 boards may be installed in a single system.
-
product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
product
PC-Based Bus Platform
PXIe 3U 8 Slot
PXI (PCI eXtensions for Instrumentation) is a PC-based bus platform for measurement and automation systems. PXI uses commercial PC-based PCI bus technology while combining rugged CompactPCI modular packaging, as well as key timing and synchronization features. While derived from cPCI, PXI adds the timing and synchronization features, among other things, that were not present in cPCI.
-
product
PC-Based Bus Platform
PXI 3U
PXI (PCI eXtensions for Instrumentation) is a PC-based bus platform for measurement and automation systems. PXI uses commercial PC-based PCI bus technology while combining rugged CompactPCI modular packaging, as well as key timing and synchronization features. While derived from cPCI, PXI adds the timing and synchronization features, among other things, that were not present in cPCI.
-
product
MTM-Bus Tester
PXIe-1149.5
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
product
PXI Interface Module, AIT MIL-STD 1553
M3406A
Interface to the LRU in avionics test solution Up to four channel MIL-STD-1553 bus interface with full error injection and detection Concurrent Bus Controller, multiple Remote Terminals (31), and Bus Monitor operation capabilities Data capture filtering, 100% bus recording, and physical bus replay Variable output voltage signal and software selectable bus coupling modes 10 high voltage (up to 30 V) programmable DIO lines PXI trigger generation on 1553 bus events
-
product
PXI LIN Interface Module
The PXI LIN Interface Module is a bus interface for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LIN Description File (LDF) databases in integrated LIN databases. PXI LIN Interface Modules work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
PCI-8517, 2-Port FlexRay Interface Device
780685-02
2-Port FlexRay Interface Device—The PCI‑8517 is designed for developing FlexRay applications. As part of the NI‑XNET platform, the PXI‑8517 works well in applications requiring real-time, high-speed manipulation of hundreds of FlexRay frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The PCI‑8517 contains two fully functional FlexRay interfaces, allowing an individual engine control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface.
-
product
PXI Express Interface
EMX-2500
The EMX-2500 is the industry’s first gigabit Ethernet LXI based PXI Express interface. This combines Ethernet's widespread usage and robust architecture with instrumentation-specific functionality, such as wired trigger bus and IEEE-1588-2008 synchronization, and extends it for use in PXI Express mainframes, making it an ideal solution for data acquisition applications.
-
product
PXIe Avionics Interface Cards
The OmniBus II PXIe is the next-generation of Astronics' popular OmniBus product with faster I/O and processing capabilities. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box. Readily available as Commercial Off-The-Shelf (COTS) products, the PCIe interface is perfect for challenging simulation, test, interface, and data recording applications.
-
product
PCIe-8510, 2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device
785325-01
2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device—The PCIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PCIe‑8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
PCIe-8510, 2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device
785324-01
2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device—The PCIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PCIe‑8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.