Showing results: 76 - 90 of 414 items found.
-
780682-01 -
NI
1‑ or 2-Port, Low‑Speed/Fault-Tolerant CAN Interface Device—The PCI‑8511 is a fault-tolerant controller area network (CAN) interface for developing applications with the NI‑XNET driver. The PCI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
AMC825-x -
AIM GmbH
ARINC825 (CAN bus) Test & Simulation module for PMC with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AMC825-x PCI Mezzanine Card (PMC) can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
ACPe825-x -
AIM GmbH
ARINC825 (CAN bus) Test & Simulation module for PCIe with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACP825 PCIe card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
MU thermocouple1 CAN FD -
PEAK-System Technik GmbH
With the MU-Thermocouple1 CAN FD, measurement data from thermocouples are recorded, pre-processed and transmitted with CAN FD. The temperature is measured via 8 connections, which are designed for the temperature measuring ranges J, K or T, depending on the product version. Temperatures can be recorded in Celsius, Fahrenheit or Kelvin and calculated with an individual factor and offset. The measurement data is then transmitted via CAN FD or via classic CAN.
-
PCAN MicroMod FD -
PEAK-System Technik GmbH
The PCAN-MicroMod FD is a small breadboard with CAN and CAN FD connection on the one hand and various physical inputs and outputs on the other. Both sides are logically linked using the NXP LPC54618 microcontroller. Electronics developers can use the PCAN-MicroMod FD to easily integrate I/O functionality with a CAN connection into their project.
-
CB1 -
North Atlantic Industries
The serial bus system with real-time capabilities is the subject of the ISO 11898 International Standard and covers the lowest two layers of the ISO/OSI Reference Model. Our CANBus modules provide independent, isolated channels of CAN serial data bus links, conforming to the ISO 11898 International Standard. All CAN nodes are able to transmit data and several CAN nodes can request the bus simultaneously.
-
CanX -
Schleissheimer Soft- und Hardwareentwicklung GmbH
CanX is the custom testing and simulation software for CAN and LIN bus for specific user groups. The run-time software is designed to execute predefined or automated tasks in testing, work preparation, production, repair or project management.
-
YAVAL964 -
6TL Engineering
- 16 channels DPDT or SPDT 2A- CAN bus control and 24Vdc (J1 and J2 connectors to chain multiple cards).- Access to relay-pins through wire-wrap or terminal block- Address selection DIP switch on top layer- LED monitoring- Drivers dll & VIs available
-
PCAN MicroMod FD Analog 1 -
PEAK-System Technik GmbH
The PCAN-MicroMod FD breadboard can be purchased together with ready-to-use motherboards that provide peripherals for specific requirements. Spring clamp connectors are used to connect CAN, I/O and supply. The motherboard PCAN-MicroMod FD Analog 1 focuses on analog inputs and outputs, which are provided with the appropriate protective circuit.
-
K- AN8 KIT -
Influx Technology LTD
This K-AN8 (8 analog + 4 digital input) kit contains everything needed to get the K-AN8 set up and tested on a work bench.To help with connecting sensors to the analog and digital ports the K-BoB enables easy connection with BNC connectors.Influx K-Cal is easily connected via the Kvaser LeafLight interface and Kvaser T-CANnector. (Using the Kvaser T-CANnector to power up the K-AN8 (at the desk) and terminate the CAN bus).
-
PCAN MicroMod FD Digital 1&2 -
PEAK-System Technik GmbH
The PCAN-MicroMod FD breadboard can be purchased together with ready-to-use motherboards that provide peripherals for specific requirements. Spring clamp connectors are used to connect CAN, I/O and supply. The main boards PCAN-MicroMod FD Digital 1 and 2 focus on digital inputs and outputs, which are provided with the appropriate protective circuit. The digital outputs of Digital 1 are equipped with low-side switches and those of Digital 2 with high-side switches.
-
-
P896 -
Validyne Engineering
The P896 is a test and measurement grade pressure transducer for applications requiring high accuracy and outstanding performance through ambient temperature changes. The P896 is digitally compensated and corrected to provide high accuracy pressure measurement in a robust cylindrical form factor.
-
K- AN8 -
Influx Technology LTD
The stackable K-AN8 is our cost effective solution to measuring analog and digital/PWM sensors together in one module. Extremely easy to use and stackable with all of our other K-series instrumentation modules. The K-AN8 includes our unique power down and WakeOnCAN feature for quick installation on long term unattended fleet test vehicles.
-
SenseNet CAN -
Cubic Systems, Inc.
The award winning SenseNet Telematics Module features all of the connectivity required to implement powerful and inexpensive Telematics solutions for military and commercial vehicle applications. SenseNet is currently in use in commercial and military vehicle applications requiring both wired and unwired sensor network connectivity and support in Condition Based Maintenance projects.