Filter Results By:
Products
Applications
Manufacturers
CANBus
Controller Area Network
-
product
CANbus
ADLINK's Intelligent Remote Data Acquisition & Control Modules (NuDAM) are designed for data acquisition systems based on PCs and other processor based equipment with standard serial I/O ports (RS-232 or RS-485 with auto direction control).The modules convert input/output signals to engineering units and transmit/receive, in ASCII format, to/from any host computer with an RS-232 or RS-485 port. NuDAM modules are the key components in flexible and cost effective remote data acquisition and control systems.
-
product
CANbus Controller
CPCI360
The CPCI360 CANbus controller is a 3U CompactPCI card based on the SJA1000. The SJA1000 provides an interface to the popular CANbus that supports both standard (11-bit) and extended (29-bit) identifier messages. Front LEDs provide diagnostic information.
-
product
CANbus Module
DS-MPE-CAN2L
The module implements a CAN protocol bus controller that performs serial communications according to the CAN 2.0A and CAN 2.0B specifications. The protocol uses a multi-master bus configuration for the transfer of frames between nodes of the network and manages error handling with no burden on the host processor. Error analysis features enabling diagnostics, system maintenance, and system optimization. A listen-only mode enables CAN bus traffic analysis and automatic bit-rate detection.
-
product
CANbus Controller for VMEbus
VME360
The VME360 CANbus controler is a 6U VMEbus board based on four SJA1000 CANbus controllers. Each SJA1000 provides an interface to the popular CANbus that supports both standard (11-bit) and extended (29-bit) identifier fields. Front panel LEDs provide diagnostical network information. The VME360 provides four CANbus interfaces. The CAN network is a serial communication protocol which efficiently supports distributed control with a high level of reliability.
-
product
CANbus Network Tester
Automatic Pin Test - automatically checks any abnormality on the OBD2 port caused by shorting (i.e., Pin 16 Power shorted to Ground), reverse polarity, and any other abnormalities
-
product
CANbus Controller Standard Interface
PCI360
The PCI360 CANbus controller PCI card is based on the SJA1000. The SJA1000 provides an interface to the popular CANbus that support both standard (11-bit) and extended (29-bit) identifier messages. LEDs provide diagnostics information.The CAN network is a serial communication protocol which efficiency supports distributed real-time control with a high level of reliability.
-
product
FMC Mezzanine Dual or Quad Canbus
NES-FMC-CAN
Sundance Multiprocessor Technology Ltd.
This is a Dual or Quad CANbus with autotest capabilities that can be used on a wide range of carriers, Standalone, PCIExpress, CompactPCI, VPX, CompactPCI Express, AdvanceTCA and AMC.
-
product
8 CANBus Channels, J1939 Protocol
CB2
The serial bus system with real-time capabilities is the subject of the ISO 11898 International Standard and covers the lowest two layers of the ISO/OSI Reference Model. Our CANBus modules provide independent, isolated channels of CAN serial data bus links, conforming to the ISO 11898 International Standard. All CAN nodes are able to transmit data and several CAN nodes can request the bus simultaneously.
-
product
8 CANBus Channels, CAN 2.0 A/B Protocol
CB1
The serial bus system with real-time capabilities is the subject of the ISO 11898 International Standard and covers the lowest two layers of the ISO/OSI Reference Model. Our CANBus modules provide independent, isolated channels of CAN serial data bus links, conforming to the ISO 11898 International Standard. All CAN nodes are able to transmit data and several CAN nodes can request the bus simultaneously.
-
product
Value-added Module With 4 Terminal Block Isolated CANBus 2.0A/B
VAM101
*4 Terminal Block Isolated CANBus 2.0A/B*Swappable modular design*Maximize I/O flexibility*2kV isolated protection*Designed for tBOX300/500 series*LVD, FCC, EN 50155 and IEC 60945 certified; CE compliant
-
product
8 CANBus Channels, CAN 2.0 A/B Protocol or J1939 Protocol
CB3
The serial bus system with real-time capabilities is the subject of the ISO 11898 International Standard and covers the lowest two layers of the ISO/OSI Reference Model. Our CANBus modules provide independent, isolated channels of CAN serial data bus links, conforming to the ISO 11898 International Standard. All CAN nodes are able to transmit data and several CAN nodes can request the bus simultaneously.
-
product
RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, COM, CANbus, 2 LANs And DIO (2-in/1-out)
IFB112
The IFB112.supports the low power consumption NXP (Freescale) i.MX6UL ARM® Cortex™-A7 528MHz SoC. The design concept of IFB112 is aiming to meet the demands of mission-critical applications. The gateway controller with IP30-rated aluminum and steel enclosure supports an extended operating temperature ranging from -40°C to 70°C, a wide voltage range of 9V - 48V DC power input with terminal block, and has been designed to withstand vibration up to 5G. For system integrators with wireless communication needs, the IFB112 has one PCI Express Mini Card slot, one SIM card slot, and two internal antennas. It supports one serial port, two LANs and one CANbus port to enable fast and efficient data acquisition and communication. Its digital I/O port provides users with a convenience of digital devices connection.
-
product
Robust RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, 1 COM, 1 LAN, DIO (4-in/4-out) And Optional CANbus
Agent200-FL-DC
*RISC-based (i.MX 6UltraLite) processor 528 MHz*256MB DDR3 SDRAM onboard*4GB eMMC flash onboard*2 PCI Express Mini Card slots (Wi-Fi or 3G/4G)*4 digital inputs and 4 digital outputs*Power input range of 9V to 48V DC with terminal block*Embedded Linux (Yocto) operating system*Fanless and compact design*Wide operating temperature range from -40°C to +70°C
-
product
Fanless Embedded System With I.MX 8M Processor, COM, LAN, USB, DIO (2-in/2-out), 2 PCIe Mini Card Slots, Optional CANBus, Power Design With ACC Ignition And E-Mark Certification For Vehicle Box PC
Agent336
The Agent336 is a RISC-based fanless embedded box PC certified with E-Mark for a variety of in-vehicle applications. The Agent336 measures only 164 x 118 x 44 mm and weight about 1.0kg. The cost-efficient embedded computer can withstand harsh operating environments with a wide operating temperature range of -40°C to +70°C and power input of 9 to 36V DC. This low power yet high-quality In-vehicle box computer is powered by the NXP i.MX 8M processor with the ARM® Cortex™-A53 microarchitecture and has a 3GB onboard LPDDR4 memory. Concerning the reliability and durability, the Agent336 comes with intelligent power management for ACC on/off delay, shutdown delay and over/under voltage protection. It runs on Linux (Yocto) and Android 8.1 operating systems. This IP40-rated RISC-based embedded gateway with strict certification is definitely the top choice for in-vehicle solutions, such as devices controller, fleet management, surveillance, and gateway. The newest RISC-based Agent336 supports two RS-232/422/485 ports, one isolated DIO, one HDMI port, two USB 3.0 A-type ports, one console port, one Gigabit LAN port, one RTC battery, one reset button, and five antenna openings. One onboard 8GB eMMC and one Micro SD card socket are available for extensive storage needs. Additionally, the rugged embedded computer has high integration ability with two full-size PCI Express Mini Card slots and one SIM card, which makes it a professional embedded system for transportation applications.
-
product
Full-Size PCI Express Mini Module With CAN Bus
AX92903
*USB to 1 channel CANBus port*Support CANOpen*51 x 30 mm
-
product
Value-added Module With COM/CAN/DIO And 3 PCI Express Mini Card Slots
VAM900
*1 4-wire isolated RS-232/422/485, 1 isolated CANBus 2.0A/B, 1 isolated DIO 8-in/8-out*Swappable modular design*Maximize I/O flexibility*2kV (COM & CANBus)/1.5 kV (DIO) isolated protection*Designed for tBOX300/500 series*EN 50155 certified; CE, LVD and FCC compliant
-
product
Qseven V1.2 SoM With I.MX287 454 MHz (Industrial) SoC, 128MB Memory, 4GB EMMC, Gigabit Ethernet, Audio And CAN
Q7M100
*Ultra low power consumption ARM9*High flexibility Qseven v1.2 compliant design*2 CANBus 2.0B compliant ports*24-bit TTL LCD*Dual 10/100 Base-T Ethernet*Audio
-
product
Inclination Sensors
*Compact and robust housing*Wide angle range*Sensor types for signal output via CANbus, as digital or analog signal*High protection rating for the requirements of harsh industrial environments*Configurable CAN sensors
-
product
Data Acquisition System - 3U 1-Slot
DAQ-31CP0G
The DAQ-31CP0G is a preconfigured rugged system with a high-performance, low power ARM® Cortex®-A9 processor. It is ideally suited to support a multitude of data acquisition applications that require high-density, multichannel, programmable communications consisting of: ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (CAN 2.0 A&B or J1939) and Dual-Port Gig-E Ethernet.
-
product
MARATON Moderate HE
MARATON is a family of MAgnetic field and RAdiation TOleraNt power supplies developed for CERN LHC. MARATON MHE represents a 12 channel low-voltage power supply for installation in a moderate hostile environment with integrated CANbus remote monitoring and control interface. Voltages, currents, temperatures and output power are controlled by the internal processor and illegal modes as well as failure will be detected.
-
product
Universal Multichannel Low Voltage Power Supply System
SY8800
- Factory configured modular system- 5 free slots for power supply modules- 3U x 19″ x 35 cm crate size- Floating channels- Local and Remote Control- Remote control via Ethernet, USB, CANBUS and RS232- Max output power: 2.5kW @ 220Vac, 1.5kW @ 115Vac- Up to 8 independent channels- Low noise
-
product
Data Acquisition - 3U 3-Slot
DAQ-33CP0G
is a preconfigured rugged system with a high-performance, low power ARM® Cortex®-A9 processor. It is ideally suited to support a multitude of military/aerospace data acquisition applications that require high-density, multichannel programmable ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (2.0 A&B or J1939); A/D Conversion; RTD Measurement; RS-232/422/485 Serial Communications Dual-Port Gig-E Ethernet.
-
product
High Line Pressure Transducer with Digital Interface
P368
The Validyne model P368 is a digital differential pressure transmitter designed for high line pressures and industrial pressure measurement applications. Full scale ranges of 8 psid to 10,000 psid are available. The on-board microprocessor provides high accuracy and improved stability in changing thermal environments. Communication via RS485, USB or CanBus provides remote zero and span adjustment as well as digital pressure readings in engineering units.
-
product
Avionics/Vehicles Bus, Serial I/O, Shared Memory, and More
Curtiss-Wright Defense Solutions
Curtiss-Wright offers a wide range of solutions for high-speed, low latency communications and shared memory products. These products are offered in a variety of form-factors including PMC, XMC, PCIe and PC/104 cards designed to support popular communications standards including 1553, ARINC 429, CANbus and Serial FPDP. Curtiss-Wright’s shared memory products are optimized for the high-speed, ultra-low latency transfer of data between multiple compute platforms. These products combine simplicity and high speed to support applications that require a high degree of synchronization and control.
-
product
Data Acquisition System - 3U 5-Slot
DAQ-35CP0G
is a preconfigured rugged system ideally suited to support a multitude of military/aerospace data acquisition applications that require "SBC-less" remote Gig-E command and control of high-density, multichannel programmable ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (CAN 2.0 A&B or J1939); A/D Conversion; RTD Measurement; RS-232/422/485 Serial Communications; Thermocouple Measurement; Discrete I/O; Differential Transceiver and Dual-Port Gig-E Ethernet.
-
product
ARINC-664 Part 7 Test and Simulation Board
EXC-664PCIe
The EXC-664PCIe board is an ARINC-664 part 7 test and simulation board designed to help integrate avionics suites, and can simulate up to two ARINC-664 P7 End Systems with full dual redundant support for receive and transmit operation. The board also contains room for two standard 4000 modules that can support multiple channels of other avionics communications protocols including MIL-STD-1553, ARINC-429, Serial, Discrete, ARINC-708 and CANbus.
-
product
Digital I/O
Curtiss-Wright Defense Solutions
Curtiss-Wright Digitial I/O cards include interfaces to LVDS, Camera Link, Serial intrefaces, CANbus and customizable I/O. With over 20 years experience in the design and production of top quality COTS signal acquisition hardware, we deilver PMC, XMC and PC/104 modules that can cope with the toughest operating environments. Offerings include a range of rugged digital I/O board level and system solutions designed to operate in extreme of temperature and vibration conditions.
-
product
Evaluation Kit
ROM-3310 Development Kit
*Evaluation kit for ROM-3310*Lower power TI sitara AM3352 1GHz processor*On board DDR3 512MB memory / 4GB Flash*HW WDT for system protection*Supports 1 GbE, 1 USB 2.0, 1 USB 2.0 OTG, 2 CANbus, 10 GPIO, 4 UART,1 I2C, 1 I2S, 1 SPI, 1 SDIO*Cable pack & Panel included*Evaluative image & test utilities built-in
-
product
Pressure Based Waves
5218
Measure pressure based Waves with the Aanderaa Wave Sensors- compact fully integrated sensors for measuring wave and tide conditionsThe 5218 wave sensor is designed to be mounted on the Aanderaa SeaGuard top-end plate or connected to SmartGuard using AiCaP CANbus or in other measurement systems using the RS-232 interface.The 5218R wave sensor sensor is designed for use with long cables by means of RS-422 full duplex interface.Both wave sensors are based on a silicon piezoresistive pressure sensor. The pressure measurements are sampled and temperature compensated by an advanced Digital Signal Processor.The wave sensor application areas are in fixed installations, either deployed in a seabed installation in shallow waters, or mounted onto a fixed structure in the upper water column.
-
product
Fanless Embedded Box PCs
ARK Ultra Rugged Series
The Fanless Embedded Systems ARK-V&S series are designed for rugged and space-critical in-vehicle and video surveillance applications. These embedded systems feature in-vehicle power (9~36Vdc, ISO-7637-2), in-vehicle certifications (E-Mark, IEC-60721-3-5 5M3), extension capability and wireless communication (GPS/G-sensor/Wi-Fi/3G/CANBus) for in-vehicle NVR applications. As for video performance, these embedded systems provide high graphic power (Up to 1080p/720p @120fps) and support IP Camera (4 Ports 10/100 PoE, IEEE802.3af) to maintain stable performance for mobile NVR