Showing results: 136 - 150 of 5247 items found.
-
E446 -
EMO Systems Canford Audio PLC
Tests 3 pin XLR leads, 2 and 3-pole B-gauge jack leads, RCA (phono) leads, most commonly used fuses, and other continuity paths using test leads supplied. Continuity indication by buzzer.
-
E445 -
EMO Systems Canford Audio PLC
Tests 3 pin XLR leads, 2 and 3-pole A-gauge jack leads, RCA (phono) leads, most commonly used fuses, and other continuity paths using test leads supplied. Continuity indication by buzzer.
-
Lambient Technologies
Sensors provide the vital link between the material under test and the instrument that measures its properties. Lambient Technologies LLC has developed a variety of disposable and reusable sensors for different applications. Click on the images below to learn more.
-
Santa Barbara Infrared, Inc.
The iProbe is an intelligent temperature sensor that can be calibrated independently of SBIR’s blackbody systems or 104i precision thermometers. These ultra-stable, highly responsive iProbes are used to provide long term accuracy and repeatability of under 0.010°C. Each iProbe incorporates onboard flash memory that allows all calibration constants and calibration date information to be stored independently of the blackbody or thermometer system. This allows iProbes to be exchanged for use on a blackbody or thermometer without any loss in stability or accuracy. To re-calibrate a system you need only exchange the current iProbe with a recently calibrated one. No special equipment is required and there is no down time in the test area.
-
Impulse Phaser -
Timco Instruments, LLC
With the introduction of direct buried, solid dielectric primary voltage cables, the IMPULSE PHASER has come into greater prominence for safely and accurately identifying buried primary cables, including jacketed neutral designs. The IMPULSE PHASER has been accurately used on paper insulated, lead covered feeders in excess of 20 miles and even on submarine cable 300 feet underwater.
-
Megger Group Ltd.
Overvoltage protection is critical to the long-term health of any cable. DC overvoltage testing (also known as withstand testing) is the most popular method of general condition and integrity assessment in the power, industrial and domestic markets. This method of testing is distinguished a number of key advantages:
-
CABLE -
SKM System Analysis Inc.
CABLE quickly solves complex three-dimensional cable pulling tension and sidewall pressure calculations, allowing you to make rapid and accurate design decisions.Don't leave installation to chance.
-
Kemo
Our cable assembly team in the UK produce the highest quality cable assemblies for use with a wide range of sensing and measurement applications. By making the cable assemblies in our own factory we are able to ensure the quality of every connection and every assembly, each cable is fully tested and its capacitance checked. Due to our experience in signal conditioning we understand the critical elements to quality signal analysis, this includes the correct cable. This is particularly true for accelerometer cables and sensors cables which can introduce significant noise issues if not used correctly.
-
M-CT-430A -
Fuzhou Metricu Technology Co Ltd
The multifunction LAN tester M-CT-430A is designed for maintenance and installation of cable, cable tracer, and HD Coaxial video level meter test in one equipment. The unit supports detect the near-end, mid-end and far-end fault point of RJ45 cable connector, and also supports Port Flash, PING test, IP address Scan, Link Monitor. Installers take the all in one cable tester, making working conditions safer and increasing productivity.
-
146907-01 -
NI
Kit, Cable Assembly, SH-37F-OM6/4, 9219 Calibration Cable Kit
-
OPENVPX-CABLE -
ELMA Electronic, Inc.
Compliant to VITA 46 and 65, the cabling assemblies are ideal for development. They can be used for I/O to bulkhead connectors and slot-to-slot connections. Front-plug versions allow testing across the backplane or full interconnect path.
-
-
TM800N -
T&M Tools Limited Co
TM800N Cable Fault Locator (hereinafter to be referred as TM800N) is used for test est cable break, short circuit faults of telephone cable, data cable, high frequency cable, coaxial cable,and so on.
-
KSG 200 / KSG 200 T -
BAUR Prüf- und Messtechnik GmbH
Cable identification withBAUR KSG 200. The KSG 200 cable identification system is used to identify single- and multi-core cables in a cable bundle or cable loom. By using the KSG 200, the risk of accidentally cutting a live phase is significantly reduced.* Cable identification on all types of de-energised cables* Reliable verification of the cable identification by means of the highly precise three-factor-analysis ATP* Safe cable identification on live low-voltage cables* Connection technology according to CAT IV/600 V
-
Scope T&M Pvt, Ltd.
After excavation, sometimes it is confusing to identify the right cable from a bunch of cables. Cable Identification is very important for the safety of field personnel – Cutting a wrong cable can be fatal. So, we require a Cable Identification System to identify the wanted cable.