Showing results: 4516 - 4530 of 5247 items found.
-
LCF-2330 -
Jewell Instruments LLC
The LCF-2330 inclinometer series now includes a 4-20mA output signal option for applications that require long cable runs. This dual axis tilt sensor is fluid damped to minimize noise and vibration interference while also offering a sharp 1 µradian resolution. An internal temperature sensor is available and dual supply, ± 5 Vdc output is an option. The LCF-2330 is an excellent solution for rugged applications such as radar & antenna leveling, weapons platform leveling, barge and offshore platform control, deviation surveys, 2-axis machine tool leveling, bridge structural monitoring, submersible control feedback, offshore platform stability and manufacturing process equipment for the aerospace industry.
-
7 -
Picoprobe
Designed as a companion probe to Models 12C and 18C for driving integrated circuit lines so the Model 12C and 18C can be used to measure the response of adjacent nodes. The Model 7 consists of a flexible 6 foot, 50 ohm coaxial cable accurately terminated to 50 ohms in order to avoid undesirable reflections. A special miniature connector receives replacement coaxial probe tips that provide a shielded environment to within 3 mm of the fine tungsten probe point, thus minimizing capacitive coupling to other parts of the circuit. The replaceable coaxial probe tips are offered in various point sizes and can also be bent to any shape in order to accommodate a variety of probing geometries.
-
VLS35 -
KD Optics Ltd.
The KD Optics VLS-35 is a pocket sized, visible source used for testing fibre optic cable installations. The unit is pocket sized with a long battery life from a PP3 battery, making it ideal for local fault finding and continuity checking of fibres.
-
DPC series -
UDEYRAJ ELECTRICALS PRIVATE LIMITED
DPC series hipots are used for proof testing of high voltage equipment in power engineering. Routine testing of the insulation and leakage is a necessary requirement for electrical equipments. Other areas include: Cable breakdown testing, capacitor charging and general laboratory use.
-
RF Test Equipment -
Seibersdorf Labor GmbH
We calibrate following types of RF test equipment:EMF test systems (frequency selective)EMF test systems (broadband)Field strength transfer standards (e.g. RefRad)Line Impedance Stabilisation Network (LISN)Cable, attenuator, couplerAntennaField Probe
-
SF2801 -
Shanghai Launch Electric Co., Ltd.
SF2801 high voltage capacitance bridge measures precisely capacitance CX and dielectric loss tanδ for various of insulation materials, power cables, insulation bushings, instrument transformers, transformers and other electrical high voltage equipment under frequency voltage.
-
Q-Card
Test package for combination module adhesion/peel tester includes a motorized test stand, digital force gauge, AC adapter/charger for 115VAC or 230VAC, data acquisition and exporting software, scoring fixture, glue fixture and necessary attachments and cables to perform the above tests.
-
Power Diagnostix Systems GmbH
Partial discharge monitoring systems can be used for permanent surveillance of insulation systems on GIS, transformers, rotating machines, motors, cables, or other high voltage equipment. These instruments are designed for long term data recording, alarm handling, event recognition, and system integration.
-
Fuzhou Metricu Technology Co Ltd
8 inch IP camera tester M-IPC-800C with analog, HD-TVI, HD-CVI, AHD, cable tracer app with toner wand, anti-sunlight and screen protecting cover, video level meter for for analog camera, TVI camera, CVI camera, AHD camera.
-
Appointech, Inc.
Testing for loss (also called "insertion loss") requires measuring the optical power lost in a cable (including fiber attenuation, connector loss and splice loss) with a fiber optic light source and power meter (LSPM) or optical loss test set (OLTS.)
-
GM1-HS -
Alpha Lab, Inc.
The Model GM1-HS measures the strength and polarity of magnetic fields up to 799.99 gauss. The thin sensor is at the end of a 100 cm flexible cable. The sensor tip is also flexible and can be bent for a variety of situations. The sensor can be held against the surface of a steel part to check for residual magnetism, or it can be bent into an "L" shape to measure inside a DC Solenoid. This meter has a resolution of .01 gauss (1/50 of the Earth's typical field) which is finer resolution than the Model GM1-ST. It is also used to map fields from large magnets (If fields are over 800 gauss, use the Model GM1-ST). The meter has immediate turn-on and updates 4 times a second. There is no setup required, making this the fastest gaussmeter available.
-
IS-*MA -
Lisun Electronics Inc.
1. The hold base can bear max 20kg, it can expanding to test all lamps such as E27/E40, all tubes such as T5/T8/T12, and all kinds of luminaries2. The hold base can be installed in the ceiling or down, it can be adjusted the height3. Hold base has four power cables connect to the outside Power Supply and max is 5KW4. The holder base is detachable. For some kinds of light sources you may need to change the position of the holder base.5. Diameter: IS-0.3M (0.3m), IS-0.5M (0.5m), IS-1.0MA (1.0m), IS-1.5MA (1.5m), IS-1.75MA (1.75m), IS-2.0MA (2.0m). Other sizes can be designed according to the customer’s request.6. The painting of integrating spheres is according to CIE Pub. No.84 (1989)
-
LV 5333 -
Leader Electronics Corp.
LV 5333 Waveform Monitor is a powerful, versatile video production tool that is compact and portable. LV 5333 has a high quality TFT LCD screen which produces high quality picture images. Waveform, Vector, Audio, Status and 5 Bar gamut displays are all included in this precision instrument. These can be displayed full screen or in various multi-display combinations. LV 5333 can also display the levels of an embedded audio signal. Plus, Cable Length, External Phase Difference, and Field Frequency Deviation measurements are standard along with CINELITE® II. Now with HD HDR monitoring as an option, the LV 5333 can be carried as a portable unit or rackmounted for studio or flypack use.
-
Arduino Ethernet Shield 2 -
Arduino llc
The Arduino Ethernet Shield 2 connects your Arduino to the internet in mere minutes. Just plug this module onto your Arduino Board, connect it to your network with an RJ45 cable (not included) and follow a few simple steps to start controlling your world through the internet. As always with Arduino, every element of the platform – hardware, software and documentation – is freely available and open-source. This means you can learn exactly how it's made and use its design as the starting point for your own circuits. Hundreds of thousands of Arduino Boards are already fueling people’s creativity all over the world, everyday. Join us now, Arduino is you! *Requires an Arduino Board (not included)
-
TE Connectivity Ltd.
Our portfolio of Bluetooth antennas includes products for internal/embedded mounting within IoT devices as well as externally mounted antennas for access points, gateways, and larger fixed infrastructure applications. Many of our internal/embedded Bluetooth antennas have an adhesive mounting retention type. Externally mounted antennas come in a variety of mounting styles, including direct mount to pole and mast mount options. Multiple connector and cable options are available for our customers to make the best choice for their applications Custom antenna developments are regularly undertaken to meet specific customer requirements. Our Bluetooth antenna portfolio includes products manufactured by TE Connectivity, Laird Connectivity External Antennas, and Hirschmann Car Communications.Read Less
