Showing results: 796 - 810 of 5247 items found.
-
Weshine Electric Manufacturing Co., Ltd
Electricity networks have had to become more flexible, reacting more quickly to the changes and needs of higher performance. This demand for flexibility is especially true where multiple generation sources occur, such as the intermittent power from renewables like solar and wind energy. While modern SMART grid technology can quickly identify faults in sub-station and generating units, cable faults can still occur anywhere on the network.
-
HydroPACT 350 -
Teledyne Marine TSS
The HydroPACT 350 provides a reliable and simple method for performing accurate submarine surveys on a tone-carrying cable. It is available as a 110V system or a 240V system, both depth rated to 3,000m with a 6,000m option.The 350 system operates in real-time and provides accurate measurements at a rate that allows integration on faster ROVs. The measurement technology used by the system also allows it to operate out of water with no degradation in performance, range or accuracy.
-
Fluke Networks
Companies expect their twisted pair cabling to work flawlessly, but corners cut during design, installation and testing result in network downtime which translates to wasted resources and lost revenue. This can be avoided by cable installers that are capable of installing copper cabling systems and locating faults quickly. From 100BASE-T to tomorrow's advanced twisted pair technology, Fluke Networks is the industry's most trusted partner for cabling testing.
-
FlexFit -
Teledyne Storm Microwave
Does your application require:- Low resistance to flexure? - Continual movement?- Low weight?- Does it have tight space constraints?Whether you're facing one or more of these issues, FlexFit™ assemblies can provide your solution. The FlexFit™ cable has a stranded center conductor that offers ultra flexibility (>500,000 flexures) with electrical and physical stability.And, its small size (0.052"/1.32 mm OD) satisfies weight and space constraints that can impact ease of installation.
-
Torontech Group
Optical fiber consists of a core and a cladding layer, selected for total internal reflection due to the difference in the refractive index between the two. In practical fibers, the cladding is usually coated with a layer of acrylate polymer or polyimide. This coating protects the fiber from damage but does not contribute to its optical waveguide properties. Individual coated fibers then have a tough resin buffer layer and/or core tube(s) extruded around them to form the cable core. Several layers of protective sheathing, depending on the application, are added to form the cable. Rigid fiber assemblies sometimes put light-absorbing ("dark") glass between the fibers, to prevent light that leaks out of one fiber from entering another. This reduces cross-talk between the fibers, or reduces flare in fiber bundle imaging applications Optical fibers are very strong, but the strength is drastically reduced by unavoidable microscopic surface flaws inherent in the manufacturing process. The initial fiber strength, as well as its change with time, must be considered relative to the stress imposed on the fiber during handling, cabling, and installation for a given set of environmental conditions. There are three basic scenarios that can lead to strength degradation and failure by inducing flaw growth: dynamic fatigue, static fatigues, and zero-stress aging.
-
SWR TRUE 3013 -
LBA Group, Inc
• A cost-effective SWR Analyzer covering all Cellular and radio communication bands 30-2700 MHz• Measures transmition & antenna impedance, frequency, SWR, return loss, and bandwidth by sweeping band of interest• Built-in synthesized RF sweep generator• SWR TRUE 3013 Antenna Analyzer gives you quick and reliable antenna and cable trouble-shooting capabilities• 5 in 1 analyzes for antenna tuning and control• Measured results can be stored for further analyzing and documentation on internal and external storage media• Time stamp and operator ID capability included• LCD Display works in direct sunlight and with backlight in dark areas
-
Autobuild™ Software -
CAMI Research Inc. (CableEye®)
Our optional, add-on AutoBuild™ software (Item 728) offers Guided Assembly for cables and wire harnesses. Use a supplied probe, or a finger with wrist strap, to touch an unterminated wire and the software shows (and says) exactly where the wire should be connected. As the operator attaches each new wire, AutoBuild checks the entire assembly and provides a clear checklist showing all completed good connections. When using our resistance-capable testers, you may connect diodes and resistors by name and value, check resistance values over the tester's specified range, and test conduction and isolation resistance against specified thresholds. Programmable tones accompany the graphic screen to give clear signals to the operator when good connections are completed or when incorrect connections, resistance violations, or diode insertions are detected. Combine with our Light Director™ option for light-guided assembly.
-
GPIB-PC104-XL -
TEAM SOLUTIONS, INC.
The ines GPIB PC/104 interface card uses the enhanced features of the ines GPIB chip , resulting in a reliable solution for industrial measurement.
-
CyberScan COND 600 -
Thermo Scientific
Measure from pure water to seawater with one meter! COND600 features a broad conductivity range with Auto-ranging Capabilities for more convenience.
-
-
-
Pickering Interfaces Ltd.
Our 20-Pin GMCT connector is used on PXI switching products to provide a low density user connector solution.
-
Pickering Interfaces Ltd.
Our 15-Pin D-Type connector is used on PXI switching products to provide a medium density user connector solution.
-
Pickering Interfaces Ltd.
Our 20-Pin Scorpion connector is used on PXI power switching products to provide a high current user connector solution.
-
93-970-301 -
Pickering Interfaces Ltd.
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.