Showing results: 811 - 825 of 5247 items found.
-
Pickering Interfaces Ltd.
These standard voltage and high voltage 50 Pin D-type connectors are used for both PXI & LXI switching and simulation products for medium density applications.
-
Pickering Interfaces Ltd.
The Standard Voltage 26-Pin D-Type connector is used on PXI products to provide a medium density user connector solution.
-
Pickering Interfaces Ltd.
These standard voltage and high voltage 9 Pin D-type connectors are used for both PXI & LXI switching and simulation products for low density applications.
-
Pickering Interfaces Ltd.
Our 50-Pin SGMC connector is used on PXI power switching products to provide a high current user connector solution with high density.
-
Pickering Interfaces Ltd.
These standard voltage and high voltage 37 Pin D-type connectors are used for both PXI & LXI switching and simulation products for medium density applications.
-
Pickering Interfaces Ltd.
Our Standard Voltage 25-Pin D-Type connector is used on PXI and LXI switching products to provide a medium density user connector solution.
-
CH2 -
Cirris Systems Corporation
The easy-wire CH2 was designed for commercial, military, and aerospace applications. Running on powerful Windows-based software, the CH2 offers unrivaled testing capabilities at an unparalleled price. Compact, easy-to-use, and FAST (shorts/mis-wires detected in <1 sec for 20,000 points), the CH2 is positioned to become the ''''tester of choice'''' for high-end users.
-
Teledyne Marine PDS
- Displays trencher depth relative to the seafloor- Real time monitoring of the operation- USBL configuration- Multibeam measurements included in the project.- Easy calibration of the sensors for the trencher
-
3702 -
Peaceful Thriving Enterprise Co Ltd
Check on 6, 24 and 48V DC systems. DC voltage mesurement and used as an extension cord for testing electrical circuits in cars , trailer, boats.
-
92-961-200-M -
Pickering Interfaces Ltd.
This connector is designed to allow users to directly terminate with soldered connections to the 200 pin LFH connector. Please note; This product is supplied without the backshell shown in the image above.
-
40-961A-200-M -
Pickering Interfaces Ltd.
This connector is designed to allow users to directly terminate with soldered connections to the 200 pin LFH connector.
-
Dx20-HiTemp -
Teledyne LeCroy
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Dx10-HiTemp -
Teledyne LeCroy
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
CB49 -
CAMI Research Inc. (CableEye®)
Populated with solder pads to accept a suite of TE-Connectivity Micro-MaTch connectors, this board addresses markets plagued by vibration and fretting corrosion, and requiring "miniaturized connectivity". Rated to 500Vdc/350Vac, the CB49 may be used on all CableEye models. The CB49, sold without connectors, contains nine sets of 20 solder pads accommodating numerous configurations of Micro-MaTch connectors. There are nine preset locations for automatic detection & display of 4, 6, 8, 10, 12, 14, 16, 18, and 20-pin connectors. Yet, any single set may be fitted with any combination of lower pin count connectors that total to 20 or less (e.g. a 14-pin with a 4-pin). Connectors soldered in non-preset positions will also appear graphically correct once they are mapped with PinMap (optional software). Sold as a set of two boards, each Micro-MaTch test board may be paired with other CableEye adapter boards to accommodate any combination of connectors.
-
10881D -
Keysight Technologies
Provide reliable power with this spade lug that connects the laser head to multiple laser boards.