Showing results: 976 - 990 of 1284 items found.
-
ABex TM-4070 DMM -
Konrad Technologies GmbH
The ABex TM-4070 is an ABex terminal module to interface with NI PXI-407x or PXIe-408x and gives the possibility to rout the DMM signals to the front connector and the Analog bus. The routing to the analog bus is software controlled and the signals are switched with reed relays.
-
CPCI-DA16-1 -
ALPHI Technology Corporation
The CPCI-DA16 is a slave Digital to Analog board that is managed by the host processor on the CPCI bus. The card contains a state machine that performs mostof the work of outputting data, in order to minimize the impact to the HOST system. The CPCI-DA16 is supported by ALPHI Technology under Windows NT by a Board Support Package which is supplied with the card. Other documentationsupplied with the card will describe this support in full detail.
-
CPCI-AD8 -
ALPHI Technology Corporation
The CPCI-AD8/16 module provides a 3U high performance data acquisition subsystem. There are (8) eight or (16) sixteen 100/200 KSPS ADC’s for maximum performance. The Local DSP can be used to simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digital filtering, etc. Software can be downloaded to the DSP via the CPCI interface.Instrumentation amplifiers provide over-voltage protection and gain on a per channel basis. The CPCI-AD8/16 can also accept external scan and trigger signals from a front panel connector.
-
CPCI-IPC -
ALPHI Technology Corporation
The CPCI-IPC module provides a 3U high performance flexible I/O scheme, that supports industry standard Industry Packs™. For application requiring low cost, high density I/O or unique combinations, the CPCI-IPC is the perfect solution. The Local DSP can be used to simply move data to and from the CPCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc. Custom application software can be downloaded to the DSP via the CompactPCI bus. A very low cost, non-intelligent version is also available, CPCI-SIP.
-
PCI-6713B-4IP -
ALPHI Technology Corporation
The PCI-6713B-4IP module provides a high performance flexible I/O scheme, thatsupports industry standard Industry Packs™. For application requiring low cost,high density I/O or unique combinations, the 6713B-4IP is the ideal solution. The local 6713B DSP can be used to simply move data to and from the PCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc. Custom application software can be downloaded to the DSP via the PCI bus. A very low cost, non-intelligent version is also available, PCI-SIP.
-
PCI-IPC -
ALPHI Technology Corporation
The PCI-IPC module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the PCI-IPC is the perfect solution.The Local DSP can be used to simply move data to and from the PCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc. Custom application software can be downloaded to the DSP via the PCI bus.
-
PCI-1553-B -
ALPHI Technology Corporation
The PCI-1553-LXE/DXE 1,2 uses UTMC’s Sµmmit LXE/DXE version, UT69151DXE-GPC 1553 communication device as its 1553 bus controller, or remote terminal, or monitor terminal. A single controller has two redundant channels. The 1553board can have 1 or 2 communication channels. The controller accesses 64Kx16 word of external memory and has internal transceivers for both channel A and B. The 3U PCI board has on-board transformers for both channels and both controllers.
-
PCI-1553-PLX -
ALPHI Technology Corporation
The PCI-1553-X uses a single UTMC’s Sµmmit or BCRTM communication device as its 1553 bus controller, or remote terminal, or monitor terminal. The single controller has two redundant channels. This controller accesses 64Kx16 word of external memory and has external for both channel A and B. The 3U PCI board has on-board transformers for both channels.
-
PCIe-Mini-ARINC429-4/8 -
ALPHI Technology Corporation
The PCIe-ARINC429-4/8 PCIexpress Mini board has an ARINC controller that supports the ARINC specifications. ARINC429 (Aeronautical Radio Incorporated) is a specification, which defines how avionics equipment and system should communicate with each other. ARINC 429 employs a unidirectional data bus standard known as Mark 33 Digital Information Transfer System (DITS). Messages are transmitted and received at a bit rate of either 12.5kbps or 100kbps.
-
MIC-3042 -
Advantech Co. Ltd.
The MIC-3042 is a 4U enclosure designed for standard cPCI power supplies. It is equipped with a cPCI 500 W redundant 2 1 power supply with hot-swap support. The system has 8 slots for CompactPCI boards and 6 slots for IEEE 1101.11 rear I/O transition boards. The MIC-3042 comes with a built-in high quality backplane that supports 64-bit / 66 MHz PCI cards.
-
Advantech Co. Ltd.
PCI/PCIe-bus non-isolated digital I/O cards for parallel data transfer, TTL DIO, and logic signal sensing.
-
Advantech Co. Ltd.
Counter cards series include pulse output cards, counter timer cards, and counter add-on cards for PCI bus and PWM measurement.
-
AmFax Ltd
PXI has become the de-facto standard for housing the high performance modular instrumentation required to meet the demands of testing today's high performance products. Based on the PCI bus, PXI (PCI Extensions for Instrumentation), this platform is used in most of our new ATE designs.
-
1000 X-Series -
Keysight Technologies
50 MHz to 100 MHz See more signal detail with 50,000 wfms/sec update rate Make professional measurements, including mask, math, FFT, analog bus, and protocol triggering/decode Quickly learn how to use; Oscilloscopes have built-in help and training signals Educators can easily set up teaching labs with the free Educator’s Resource Kit
-
U4322A -
Keysight Technologies
Keysight's PCIe 3.0 analyzer uses Keysight's unique ESP (Equalization Snoop Probe) technology, with the ability to tune the equalization algorithm used according to the type of channel the analyzer is monitoring. This ensures that the data captured in the analyzer is exactly what is on the wire. Without this capability, at 8GT/s, there is a high likelihood of misrepresentation of the data on the bus, which can lead to wasted hours, if not days in the validation cycle.